2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR DOOR INSIDE HANDLE BEZEL

  1. B180907E01
    Using a screwdriver, detach the 4 claws and remove the bezel.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


3. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY

  1. B180908
    Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the armrest base panel.


4. REMOVE ASSIST GRIP COVER

  1. B180910
    Using a moulding remover, detach the 9 claws and remove the door assist grip cover.


5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B180912
    Remove the 3 screws.

  1. Remove the 9 clips, 4 claws and trim board.

  1. Disconnect the connector and remove the trim board.

  1. B180913
    Disconnect the 2 cables from the inside handle.


6. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP

  1. B180917E01
    Remove the weatherstrip by pulling it upward in the direction indicated by the arrow.


7. REMOVE REAR SPEAKER SET (w/ Rear Speaker)

  1. B181520
    Disconnect the speaker connector.

  1. Remove the 3 screws.

  1. Detach the claw and remove the speaker.

    NOTICE:
    Do not touch the cone part of the speaker.


8. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B183933E01
    Using a clip remover, detach the 6 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the service hole cover.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE REAR DOOR GLASS RUN

  1. B180919
    Remove the rear door glass run from the window frame.


10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

  1. B180920
    Remove the 2 bolts.

  1. Remove the screw and window frame.


11. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B180923
    Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.


12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B180921
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


13. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B180924E05
    Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 3 bolts and regulator.

    NOTICE:
    Be careful when removing the bolts as the motor may fall and become damaged.

  1. Remove the temporary bolt from the rear door window regulator sub-assembly.


14. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B294158E01
    Using a T25 "TORX" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.

    Text in Illustration 
    *A
    for Models with Jam Protection Function on 4 Windows
    *B
    for Models with Jam Protection Function on Driver Door Window Only

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →