TERMINALS OF ECU
System information · Vehicles built from Sep 2011
| CHECK TRANSPONDER KEY AMPLIFIER |


Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
E95-7 (AGND) - Body ground
-
SB - Body ground
Ground
Always
Below 1 Ω
-
E95-1 (VC5) - E95-7 (AGND)
Input
P - SB
Transponder key amplifier power supply
No key in ignition key cylinder
Below 1 V
-
E95-4 (CODE) - E95-7 (AGND)
Output
V - SB
Demodulated signal of key code data
No key in ignition key cylinder
Below 1 V
-
E95-5 (TXCT) - E95-7 (AGND)
Input
LG - SB
Key code output signal
No key in ignition key cylinder
Below 1 V
-
Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
E95-1 (VC5) - E95-7 (AGND)
Input
P - SB
Transponder key amplifier power supply
Key inserted in ignition key cylinder
Pulse generation
(See waveform 1)
- BCC Malfunction
- Abnormal Status
- Different Encrypt Code
- Different Serial Number
E95-4 (CODE) - E95-7 (AGND)
Output
V - SB
Demodulated signal of key code data
Key inserted in ignition key cylinder
Pulse generation
(See waveform 2)
E95-5 (TXCT) - E95-7 (AGND)
Input
LG - SB
Key code output signal
Key inserted in ignition key cylinder
Pulse generation
(See waveform 3)
- BCC Malfunction
Inspect using an oscilloscope.
- NOTICE:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
E95-1 (VC5) - E95-7 (AGND)
Tool Setting
1 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
E95-4 (CODE) - E95-7 (AGND)
Tool Setting
1 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 3 (Reference)

Measurement Condition Item
Content
Tester Connection
E95-5 (TXCT) - E95-7 (AGND)
Tool Setting
1 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
| CHECK TRANSPONDER KEY ECU ASSEMBLY |


Disconnect the E96 transponder key ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
E96-16 (GND) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
E96-1 (+B) - E96-16 (GND)
Input
B - W-B
Battery
Always
11 to 14 V
+B
E96-2 (IG) - E96-16 (GND)
Input
B - W-B
Ignition switch
Ignition switch off
Below 1 V
IG SW
Ignition switch ON
11 to 14 V
E96-3 (KSW) - E96-16 (GND)
Input
G - W-B
Unlock warning switch
No key in ignition key cylinder
10 kΩ or higher
Key SW/B2780
Key inserted in ignition key cylinder
Below 1 Ω
Reconnect the E96 transponder key ECU connector.
Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
E96-14 (VC5) - E96-16 (GND)
Input
P - W-B
Transponder key amplifier power supply
No key in ignition key cylinder
Below 1 V
- BCC Malfunction
- Abnormal Status
- Different Encrypt Code
- Different Serial Number
Key inserted in ignition key cylinder
Pulse generation
(See waveform 1)
E96-4 (TXCT) - E96-16 (GND)
Input
LG - W-B
Key code output signal
No key in ignition key cylinder
Below 1 V
Key inserted in ignition key cylinder
Pulse generation
(See waveform 2)
E96-15 (CODE) - E96-16 (GND)
Output
V - W-B
Demodulated signal of key code data
No key in ignition key cylinder
Below 1 V
Key inserted in ignition key cylinder
Pulse generation
(See waveform 3)
E96-13 (EFIO) - E96-16 (GND)
Input
R - W-B
ECM output signal
Ignition switch off
Below 1 V
E/G Start Permission
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
Pulse generation
(See waveform 4)
E96-12 (EFII) - E96-16 (GND)
Output
W - W-B
ECM input signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
Pulse generation
(See waveform 5)
E/G Start Permission
E96-9 (D) - E96-16 (GND)
Input/Output
R - W-B
Diagnosis tester communication
Always
Pulse generation
-
E96-5 (AGND) - Body ground
-
SB - Body ground
Transponder key amplifier ground
Always
Below 1 Ω
-
E96-8 (IND) - Body ground
Output
V - Body ground
Security indicator signal
No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to ACC or off (engine immobiliser system set)
Pulse generation
-
Key in ignition key cylinder (engine immobiliser system unset)
Below 1 V
- BCC Malfunction
Inspect using an oscilloscope.
- NOTICE:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
E96-14 (VC5) - E96-16 (GND)
Tool Setting
1 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
E96-4 (TXCT) - E96-16 (GND)
Tool Setting
1 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 3 (Reference)

Measurement Condition Item
Content
Tester Connection
E96-15 (CODE) - E96-16 (GND)
Tool Setting
1 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 4 (Reference)


Text in Illustration *a
Waveform A
*b
Waveform B
*c
Approximately 160 ms
*d
Approximately 510 ms
*e
Approximately 270 ms
-
-
Measurement Condition Item
Content
Tester Connection
E96-13 (EFIO) - E96-16 (GND)
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
Waveform 5 (Reference)


Text in Illustration *a
Waveform A
*b
Waveform B
*c
Approximately 160 ms
*d
Approximately 510 ms
*e
Approximately 270 ms
-
-
Measurement Condition Item
Content
Tester Connection
E96-12 (EFII) - E96-16 (GND)
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
| CHECK ECM (for 1GR-FE) |


for LHD:
Measure the voltage and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
C45-81 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A38-20 (BATT) - C45-81 (E1)
Input
L - BR
+B power supply
Always
11 to 14 V
-
A38-1 (+B2) - C45-81 (E1)
Input
B - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A38-2 (+B) - C45-81 (E1)
Input
B - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A38-10 (IMO) - C45-81 (E1)
Input
W-R - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication input
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 1)
-
A38-11 (IMI) - C45-81 (E1)
Output
R-G - BR
Transponder key ECU assembly communication output
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication output
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 2)
-
for RHD:
Measure the voltage and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
C46-81 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A52-20 (BATT) - C46-81 (E1)
Input
L - BR
+B power supply
Always
11 to 14 V
-
A52-1 (+B2) - C46-81 (E1)
Input
B - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A52-2 (+B) - C46-81 (E1)
Input
B - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A52-10 (IMO) - C46-81 (E1)
Input
W-R - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication input
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 1)
-
A52-11 (IMI) - C46-81 (E1)
Output
R-G - BR
Transponder key ECU assembly communication output
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication output
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 2)
-
Inspect using an oscilloscope.
Waveform 1 (Reference)


Text in Illustration *a
Waveform A
*b
Waveform B
*c
Approximately 160 ms
*d
Approximately 510 ms
*e
Approximately 270 ms
-
-
Measurement Condition Item
Content
Tester Connection
A38-10 (IMO) - C45-81 (E1)*1
A52-10 (IMO) - C46-81 (E1)*2
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
- *1: for LHD
- *2: for RHD
- *1: for LHD
Waveform 2 (Reference)


Text in Illustration *a
Waveform A
*b
Waveform B
*c
Approximately 160 ms
*d
Approximately 510 ms
*e
Approximately 270 ms
-
-
Measurement Condition Item
Content
Tester Connection
A38-11 (IMI) - C45-81 (E1)*1
A52-11 (IMI) - C46-81 (E1)*2
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
- *1: for LHD
- *2: for RHD
- *1: for LHD
| CHECK ECM (for 1VD-FTV) |


for LHD:
Measure the voltage and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
C45-81 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A38-20 (BATT) - C45-81 (E1)
Input
L - BR
+B power supply
Always
11 to 14 V
-
A38-2 (+B) - C45-81 (E1)
Input
B - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A38-10 (IMO) - C45-81 (E1)
Input
W-R - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication input
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 1)
-
A38-11 (IMI) - C45-81 (E1)
Output
R-G - BR
Transponder key ECU assembly communication output
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication output
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 2)
-
for RHD:
Measure the voltage and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
C46-81 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A52-20 (BATT) - C46-81 (E1)
Input
L - BR
+B power supply
Always
11 to 14 V
-
A52-2 (+B) - C46-81 (E1)
Input
B - BR
+B power supply
Ignition switch ON
11 to 14 V
-
A52-10 (IMO) - C46-81 (E1)
Input
W-R - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication input
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 1)
-
A52-11 (IMI) - C46-81 (E1)
Output
R-G - BR
Transponder key ECU assembly communication output
Ignition switch off
11 to 14 V
-
Transponder key ECU assembly communication output
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected.
Pulse generation
(See waveform 2)
-
Inspect using an oscilloscope.
Waveform 1 (Reference)


Text in Illustration *a
Waveform A
*b
Waveform B
*c
Approximately 160 ms
*d
Approximately 510 ms
*e
Approximately 270 ms
-
-
Measurement Condition Item
Content
Tester Connection
A38-10 (IMO) - C45-81 (E1)*1
A52-10 (IMO) - C46-81 (E1)*2
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
- *1: for LHD
- *2: for RHD
- *1: for LHD
Waveform 2 (Reference)


Text in Illustration *a
Waveform A
*b
Waveform B
*c
Approximately 160 ms
*d
Approximately 510 ms
*e
Approximately 270 ms
-
-
Measurement Condition Item
Content
Tester Connection
A38-11 (IMI) - C45-81 (E1)*1
A52-11 (IMI) - C46-81 (E1)*2
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
- *1: for LHD
- *2: for RHD
- *1: for LHD