2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REPLACEMENT

Removal / installation · Vehicles built Sep 2011 – Dec 2011

CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A208611
    Remove the 5 bolts and No. 1 engine under cover sub-assembly LH.

    HINT:
    A208795E01
    If the No. 1 cooler packing is not divided, remove both sides of the No. 1 engine under cover and cut the packing at the perforation indicated in the illustration.


4. REMOVE REAR ENGINE UNDER COVER SEAL

  1. A178890
    Remove the 2 bolts and cover seal.


5. DRAIN ENGINE OIL

  1. A178891
    Remove the oil drain plug and gasket, and drain the engine oil into a container.


6. REMOVE OIL FILTER ASSEMBLY

  1. A150109E01
    Using SST, remove the oil filter.
    SST
    09228-07501  


7. INSTALL OIL FILTER ASSEMBLY

  1. A150110
    Clean and check the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. A150111E02
    Using SST, tighten the oil filter. Choose from the following to tighten the oil filter.
    SST
    09228-07501  

    1. Using a torque wrench, tighten the oil filter.

      Torque:
      17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    2. Tighten the oil filter a 3/4 turn by hand or with a common wrench.


8. ADD ENGINE OIL
  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Add new engine oil.

    Standard Engine Oil:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil
    10W-30
    (10W-30 is best choice for fuel economy and good starting in cold weather).
    API grade SL or SM multigrade engine oil
    10W-30

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)


9. INSTALL OIL FILLER CAP SUB-ASSEMBLY

10. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


11. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


12. INSTALL REAR ENGINE UNDER COVER SEAL

  1. A178890
    Install the cover seal with the 2 bolts.


13. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A208611
    Install the No. 1 engine under cover with the 5 bolts.

    HINT:
    A209602E01
    Make sure there is no gap between the ends of the No. 1 cooler packing.


14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.

← COMPONENTS (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →