2011-2013 Land Cruiser · Service Manual General

TORQUE SPECIFICATIONS

Specifications · Vehicles built from Sep 2011

Camshaft 
Part Tightened
N*m
kgf*cm
ft.*lbf
Camshaft housing LH x Cylinder head LH
for Bolt A
10
102
7
for Except bolt
30
306
22
Camshaft bearing cap LH x Camshaft housing LH
16
163
12
Camshaft housing RH x Cylinder head RH
for Bolt A
10
102
7
for Except bolt
30
306
22
Camshaft bearing cap RH x Camshaft housing RH
16
163
12
Cylinder Head Gasket 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder head LH x Cylinder block
1st
36
367
27
2nd
Turn 90°
3rd
Turn 90°
for 12 mm head
21
214
15
Cylinder head RH x Cylinder block
1st
36
367
27
2nd
Turn 90°
3rd
Turn 90°
for 12 mm head
21
214
15
Front Crankshaft Oil Seal 
Part Tightened
N*m
kgf*cm
ft.*lbf
No. 2 water by-pass pipe sub-assembly x Timing chain cover and front water by-pass pipe
10
102
7
Engine Assembly 
Part Tightened
N*m
kgf*cm
ft.*lbf
Engine hanger x Cylinder head
43
438
32
No. 2 front engine mounting bracket LH x Body
32
326
24
Front engine mounting insulator LH x Front No. 1 engine mounting bracket LH
72
734
53
Front engine mounting insulator RH x Front No. 1 engine mounting bracket RH
72
734
53
Engine mounting insulator x Body
79
806
58
No. 2 water by-pass pipe x Cylinder head cover RH
18
184
13
Oil cooler pipe x No. 1 oil pan and bracket
14
143
10
Drive plate and ring gear x Crankshaft
1st
30
301
22
2nd
Turn 90°
Rear No. 1 engine mounting insulator x Automatic transmission
59
602
44
Front engine mounting insulator RH x Rear No. 1 engine mounting insulator
12
122
9
Engine oil level dipstick guide x Cylinder head cover RH
10
102
7
Engine wire x Engine room junction block
10
102
7
Ground wire x bracket
8.0
82
71 in.*lbf
Ground wire x Body
8.4
86
74 in.*lbf
Engine wire x Battery positive (+) battery cable
5.4
55
48 in.*lbf
Ground wire x Cylinder head cover RH
8.0
82
71 in.*lbf
Air cleaner x Body
5.0
51
44 in.*lbf
No. 2 engine under cover x Body
29
296
21
No. 1 engine under cover sub-assembly x Body
29
296
21
Engine hood x Hinge
13
133
10
Engine hood x Hood support
18
184
13
Engine Unit 
Part Tightened
N*m
kgf*cm
ft.*lbf
Camshaft timing gear x Camshaft
100
1020
74
Camshaft timing exhaust gear x Camshaft
100
1020
74
Timing chain cover stud bolt
20
204
15
Oil pan stud bolt (E6 and E7 "TORX")
for stud bolt A
5.0
51
44 in.*lbf
for stud bolt B
9.0
92
80 in.*lbf
Oil drain pipe x Cylinder block
10
102
7
Rear engine oil seal retainer x Cylinder block
10
102
7
Oil strainer x Oil pan
12
122
9
No. 1 oil pan baffle plate x Oil pan
12
122
9
No. 1 oil pan x cylinder block
for bolt A
10
102
7
for bolt B
35
357
26
for Nut
35
357
26
No. 2 oil pan x No. 1 oil pan
10
102
7
No. 1 heat exchanger cover x Cylinder block
21
214
15
No. 2 chain tensioner x Cylinder head RH
10
102
7
No. 1 chain vibration damper RH x Cylinder head RH and cylinder block
21
214
15
No. 1 chain tensioner RH x Cylinder head RH
10
102
7
No. 3 chain tensioner x Cylinder head LH
10
102
7
No. 1 chain tensioner LH x Cylinder block
10
102
7
No. 1 chain vibration damper LH x Cylinder head LH and cylinder block
21
214
15
Cylinder head cover spacer x Cylinder head cover
10
102
7
Camshaft oil control valve x Cylinder head cover
10
102
7
Crankshaft position sensor x No. 1 oil pan
10
102
7
Crankshaft position sensor protector x No. 1 oil pan
10
102
7
Camshaft position sensor x Cylinder head cover
10
102
7
VVT sensor x Cylinder head cover
10
102
7
Spark plug x Cylinder head
21
214
15
Oil filler cap housing x Cylinder head cover LH
10
102
7
Noise filter x Cylinder head cover
7.0
71
62 in.*lbf
Ignition coil x Cylinder head cover
10
102
7
Front No. 1 engine mounting bracket LH x Cylinder block
35
357
26
Front No. 1 engine mounting bracket RH x Cylinder block
35
357
26
Cylinder block water drain cock x Cylinder block
30
306
22
Water drain cock plug x Water drain cock
13
133
10
Knock sensor x Cylinder block
20
204
15
Separator case x No. 1 heat exchanger cover
10
102
7
Water by-pass pipe sub-assembly x Cylinder head cover RH and cylinder head RH
10
102
7
No. 2 fuel tube x Cylinder head cover
10
102
7
Intake manifold x Cylinder head
21
214
15
Wire bracket x Intake manifold
8.0
82
71 in.*lbf
Engine wire x Cylinder head
8.5
87
75 in.*lbf
Ground wire x No. 1 oil pan
20
204
15
Cylinder Head 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder head stud bolt
E7 and E8 "TORX"
9.0
92
80 in.*lbf
No. 2 straight screw plug x Cylinder head
85
867
63
No. 1 straight screw plug x Cylinder head
44
449
32
Cylinder Block 
Part Tightened
N*m
kgf*cm
ft.*lbf
Connecting rod x Connecting rod cap
1st
40
408
30
2nd
Turn 90°
Crankshaft bearing cap x Cylinder block
for inside position
61
622
45
for outside position
27
275
20
2nd
Turn 90°
for cylinder block side position
45
459
33
Cylinder block stud bolt
for stud bolt A (E8 "TORX")
20
204
15
for stud bolt B (E8 "TORX")
9.0
92
80 in.*lbf
No. 1 oil nozzle x Cylinder block
10
102
7
← SERVICE DATA (from Sep 2011)SERVICE DATA (Sep 2011 – Dec 2011) →