DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body Electrical, Powertrain or Chassis / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
Combination Meter Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ODO/TRIP Change SW
Trip switch (ODO/TRIP switch) condition / ON or OFF
ON: Trip switch (ODO/TRIP switch) pushed
OFF: Trip switch (ODO/TRIP switch) not pushed
-
Tail Cancel SW
TAIL cancel switch condition / ON or OFF
ON: TAIL cancel switch on
OFF: TAIL cancel switch off
-
Washer Switch
Washer switch / ON or OFF
ON: Washer switch on
OFF: Washer switch off
-
P-Seatbelt Buckle SW
Front passenger side seat belt warning light request signal / ON or OFF
ON: Tongue plate (for front passenger side) inserted
OFF: Tongue plate (for front passenger side) not inserted
-
Oil Level SW
Oil level switch / ON or OFF
ON: Oil level switch on
OFF: Oil level switch off
-
Water Level SW
Water level switch / ON or OFF
ON: Water level switch on
OFF: Water level switch off
-
Multi Display Select Switch
Steering multi-display select switch / ON or OFF
ON: Steering multi-display select switch on
OFF: Steering multi-display select switch off
-
Vehicle Speed Meter
Vehicle speed / Min.: 0 (0), Max.: 255 (158)
Almost same as actual vehicle speed (when driving)
Unit: km/h (mph)
Engine Rpm
Engine speed / Min.: 0, Max.: 12750
Idling: 700 to 800
Unit: rpm
Coolant Temperature
Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284)
After warming up: 80 to 105 (176 to 221)
- Unit: °C (°F).
- If the value is -40 (-40): The sensor circuit is open.
- If the value is 140 (284): The sensor circuit is shorted.
Fuel Input
Fuel sender gauge input / Min.: 0, Max.: 127.5
Fuel sender input value
Unit: L
Rheostat value
Light control rheostat switch input / Min.: 0, Max.: 100
Light control rheostat switch is fully turned right (0) → fully turned left (100)
Unit: %
Communication ECM/Meter DTC 3
ECM communication stop history / Rec or Unrec
Rec: DTC is stored
Unrec: DTC is not stored
-
ECM ODO (History 3)
ECM odometer history / Min.: 0, Max.: 999999
With history: 0 to 999999
Without history: ffffffh
-
Communication ECM/Meter DTC 2
ECM communication stop history / Rec or Unrec
Rec: DTC is stored
Unrec: DTC is not stored
-
ECM ODO (History 2)
ECM odometer history / Min.: 0, Max.: 999999
With history: 0 to 999999
Without history: ffffffh
-
Communication ECM/Meter DTC 1
ECM communication stop history / Rec or Unrec
Rec: DTC is stored
Unrec: DTC is not stored
-
ECM ODO (History 1)
ECM odometer history / Min.: 0, Max.: 999999
With history: 0 to 999999
Without history: ffffffh
-
Communication ABS/Meter DTC 3
Skid control ECU communication stop history / Rec or Unrec
Rec: DTC is stored
Unrec: DTC is not stored
-
ABS/VSC ODO (History 3)
Skid control ECU odometer history / Min.: 0, Max.: 999999
With history: 0 to 999999
Without history: ffffffh
-
Communication ABS/Meter DTC 2
Skid control ECU communication stop history / Rec or Unrec
Rec: DTC is stored
Unrec: DTC is not stored
-
ABS/VSC ODO (History 2)
Skid control ECU odometer history / Min.: 0, Max.: 999999
With history: 0 to 999999
Without history: ffffffh
-
Communication ABS/Meter DTC 1
Skid control ECU communication stop history / Rec or Unrec
Rec: DTC is stored
Unrec: DTC is not stored
-
ABS/VSC ODO (History 1)
Skid control ECU odometer history / Min.: 0, Max.: 999999
With history: 0 to 999999
Without history: ffffffh
-
Units By Region
Unit of display setting / Km/l JP, Km/l, Mi/g US or Mi/g UK
Displays unit setting
-
Language
Language of display setting / English, Spanish, French*, German* or Italian*
Displays language setting
-
Driver Side Seatbelt Warning Buzzer
Driver side seat belt warning buzzer setting / ON or OFF
ON: Driver side seat belt warning buzzer on setting
OFF: Driver side seat belt warning buzzer off setting
-
P-Seatbelt Warning Buzzer
Front passenger side seat belt warning buzzer setting / ON or OFF
ON: Front passenger side seat belt warning buzzer on setting
OFF: Front passenger side seat belt warning buzzer off setting
-
Sub Fuel Input
Fuel sender gauge input / Min.: 0, Max.: 127.5
Fuel sender input value
Unit: L
Integrated value for Oil Maintenance
Oil maintenance warning integrated value / Min.: 0 (0), Max.: 25500 (41037)
0 (0) to 25500 (41037)
Unit: mile
Integrated value for Timing belt
T-belt indicator integrated value / Min.: 0, Max.: 6553500
0 to 6553500
Unit: km/h
+B Voltage Value
+B voltage / Min.: 0, Max.: 25.5
Below 1 to 14
Unit: V
Coolant Temperature
Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284)
After warming up: 80 to 105 (176 to 221)
- Unit: °C (°F)
- If the value is -40 (-40): The sensor circuit is open.
- If the value is 140 (284): The sensor circuit is shorted.
Engine Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Engine Rpm
Engine speed / Min.: 0, Max.: 16383.75
Idling: 700 to 800
Unit: rpm
Vehicle Speed Meter
Vehicle speed / Min.: 0 (0), Max.: 255 (158)
Actual vehicle speed
- Unit: km/h (mph)
- The speed is indicated on the speedometer.
Coolant Temperature*1
Engine coolant temperature:
Min.: -40°C, Max.: 140°C
80 to 100°C (176 to 212):
After warming up
- If the value is -40°C (-40°F), The sensor circuit is open.
- If the value is 140°C (284°F) or higher, The sensor circuit is shorted.
Coolant Temperature*2
Engine coolant temperature /
Min.: -40°C, Max.: 140°C
After warming up engine: 75 to 90°C (167 to 194°F)
- If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
- After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.
- HINT:
- *1: except 1VD-FTV
- *2: for 1VD-FTV
- Unit: °C (°F).
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body Electrical / (Combination Meter) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Speed Meter Operation*1
Speedometer
0, 40, 80, 120, 160, 200, 240 or 280
Perform the test with the vehicle stopped and engine idling.
Tachometer operation
Tachometer
0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000
Perform the test with the vehicle stopped and engine idling.
Fuel Meter Operation
Fuel receiver gauge
EMPTY, 1/4, FULL
Perform the test with the vehicle stopped and engine idling.
Volt Meter Operation
Voltmeter
0, 3, 6, 9, 12, 15 or 18
Perform the test with the vehicle stopped and engine idling.
Oil Pressure Meter Operation
Oil pressure receiver gauge
LOW, 1/4, 1/2, 3/4 or HIGH
Perform the test with the vehicle stopped and engine idling.
A/T Indicator operation (1)
A/T indicator (normal mode)
P, R, N, D, 4, 3, 2, L
Perform the test with the vehicle stopped and engine idling.
A/T Indicator operation (2)
A/T indicator (sequential mode)
Es, 5 or 6
Perform the test with the vehicle stopped and engine idling.
Meter Display 1*2
All dots in the multi-information display
ALL, 0, 1, 2, 3, 4, 5 or 6
Perform the test with the vehicle stopped and engine idling.
Meter Display 2*2
All dots in the multi-information display
7, 8 or 9
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Beam
BEAM indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Head
HEAD indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Tail
TAIL indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Fr FOG
FRONT FOG indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Airbag
SRS warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Precrash
PCS indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Driver Side Seat Belt
Driver side seat belt warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Front Passenger Side Seat Belt
Passenger side seat belt warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Doors All Open
All doors open light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Washer
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Fuel
Low fuel warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Charge
CHARGE warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp ABS
ABS warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Slip*6
SLIP indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Brake
Brake warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp oil Level
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp ECT PWR
ECT PWR indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
A/T Oil Temperature Operation
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Cruise*7
Cruise control indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. KEY
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Master Warning
Master warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Clearance Sonar LCD
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. INTUITIVE P/A LCD
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp VSC OFF*6
Multi-information display
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. 2nd START
2nd START indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Ctr DIFF LOCK
Center differential lock indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. 4LO
4LO indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. CRAWL*6
CRAWL indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. A/T P
A/T P indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Water Temperature Meter Operation
Engine coolant temperature receiver gauge
LOW, NORMAL or HIGH
Perform the test with the vehicle stopped and engine idling.
Indicat. GLOW*5
Glow indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Lamp Water Level
Fuel filter and sedimenter indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Over Speed
Speed limit indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
VSC TRC Indicator*6
TRC OFF indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
PPS Indicator
Power steering warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. ECONO
Eco driving indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. SET*7
SET indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Radar Cruise Indicator*3
Radar cruise control indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Rr Inner Wheel Control Indicator*6
Turn assist indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
OFF Road Guidance Indicator*8
Multi-terrain select indicator light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
Indicat. Headlamp Auto Leveling*4
Headlight beam level control system warning light
ON or OFF
Perform the test with the vehicle stopped and engine idling.
- HINT:
- *1:
- The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
- The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
- The needle position should be within the acceptable range.
- The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
- *2: If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.
- *3: w/ Dynamic Radar Cruise Control System
- *4: w/ Headlight Leveling
- *5: for 1VD-FTV
- *6: w/ VSC
- *7: w/ Cruise Control System
- *8: w/ Multi-terrain Select
| Tester Display |
Test Part |
Control Range |
Diagnostic Note |
| Dimmer Signal |
Illumination dimming operation |
ON or OFF |
- |