2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A174194
    Remove the 2 bolts and No. 2 engine under cover seal.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174123E02
    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Tighten the radiator drain cock plug by hand.


6. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A174196E03
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


7. REMOVE FAN AND GENERATOR V BELT

  1. A163770E03
    While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
    Text in Illustration 
    *1
    Bar

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.


8. REMOVE OIL FILTER ELEMENT

  1. A094910E10
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A207196
    Remove the oil filter drain plug.

  1. A237032E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A207198
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A207199E02
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A209947E02
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


9. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A163657
    Disconnect the sender gauge connector.

  1. A162467
    Remove the oil pressure sender gauge.


10. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A178491
    Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


11. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A162468
    Remove the 3 bolts.

  1. Disconnect the 4 hoses and remove the water by-pass pipe.


12. REMOVE NO. 1 OIL COOLER BRACKET

  1. A163672
    Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.


13. REMOVE OIL FILTER BRACKET

  1. A162469
    Remove the 2 bolts, 2 nuts and filter bracket.

  1. A162470
    Remove the 2 O-rings.


14. REMOVE OIL COOLER ASSEMBLY

  1. A162471
    Remove the 5 nuts and oil cooler from the oil filter bracket.

  1. A162475
    Remove the 2 O-rings.


15. REMOVE OIL COOLER SPACER

  1. A162472
    Remove the bolt and oil cooler spacer from the oil filter bracket.

  1. A162474E04
    Remove the gasket.
    Text in Illustration 
    *1
    Gasket

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →