2011-2013 Land Cruiser · Service Manual Drivetrain

REPLACEMENT

Removal / installation · Vehicles built from Sep 2011


1. DRAIN DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. C174596
    for Front Differential:

    1. Remove the engine under cover.

    2. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    3. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    4. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. for Rear Differential:

    1. Remove the filler plug and gasket.

    2. Remove the drain plug and gasket, and drain the oil.

    3. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }


2. DISCONNECT PROPELLER SHAFT ASSEMBLY

  1. C172482E01
    Place matchmarks on the rear propeller shaft and companion flange.

  1. Remove the 4 nuts, 4 washers and 4 bolts, and disconnect the propeller shaft from the differential side.

  1. Support the propeller shaft securely.


3. REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

  1. C089309E04
    Using SST and a hammer, loosen the staked part of the nut.
    SST
    09930-00010  

  1. B087842E05
    Using SST to hold the companion flange, remove the nut.
    SST
    09330-00021   (09330-00030)


4. REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

  1. C161823E03
    Using SST, remove the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C161824E02
    Using SST, remove the oil seal.
    SST
    09308-10010  


6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C161825E02
    Using SST, remove the front bearing (inner race) from the drive pinion.
    SST
    09556-22010  

  1. C161826E02
    Using SST, remove the front bearing (outer race) from the drive pinion.
    SST
    09308-00010  


8. REPLACE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C163578
    Replace the bearing spacer with a new one.


9. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C161827E02
    Using SST and a hammer, tap in the bearing (outer race).
    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the bearing (inner race).


10. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

11. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C161828E02
    Using SST and a hammer, tap in a new oil seal.
    SST
    09214-76011  

    Standard oil seal depth:
    0.05 to 0.95 mm (0.00197 to 0.0374 in.)

  1. Coat the lip of the oil seal with MP grease.


12. INSTALL REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

  1. C161829E02
    Using SST, install the companion flange to the drive pinion.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


13. ADJUST DRIVE PINION PRELOAD
  1. Coat the threads of a new nut with hypoid gear oil.

  1. C088916E05
    Using SST to hold the companion flange, install the nut by tightening it until the standard preload is reached.
    SST
    09330-00021   (09330-00030)

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less

  1. C124126
    Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Bearing
    Specified Condition
    New
    1.0 to 1.7 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.9 to 1.4 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)

    If the preload is not within the specification, adjust the preload.


14. STAKE DRIVE PINION COMPANION FLANGE REAR NUT

  1. C089310
    Using a chisel and hammer, stake the nut.


15. CONNECT PROPELLER SHAFT ASSEMBLY

  1. C172481E01
    Align the matchmarks on the propeller shaft flange and transfer.

  1. Connect the propeller shaft with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 900 kgf*cm , 65 ft.*lbf }

  1. C178527E01
    Align the matchmarks on the propeller shaft flange and rear differential.

  1. Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    88 N*m{ 900 kgf*cm , 65 ft.*lbf }


16. ADD DIFFERENTIAL OIL

  1. D025304E27
    Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Front differential oil type and viscosity:
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent

    Rear Differential Oil Type and Viscosity:
    Item
    Oil Type and Viscosity
    w/o LSD
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    w/ LSD
    Toyota Genuine Differential gear oil LX 75W-85 GL-5 or equivalent

    Front differential capacity:
    1.85 to 1.95 liters (1.96 to 2.06 US qts., 1.63 to 1.71 Imp. qts.)

    Rear Differential Capacity:
    Item
    Specified Condition
    Standard
    4.15 to 4.25 liters (4.39 to 4.49 US qts., 3.66 to 3.74 Imp. qts.)
    w/ LSD
    4.10 to 4.20 liters (4.34 to 4.43 US qts., 3.60 to 3.69 Imp. qts.)
    w/ Differential lock

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    2. Install the engine under cover.

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

← COMPONENTS (from Sep 2011)COMPONENTS (from Sep 2011) →