2011-2013 Land Cruiser · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE

  1. F001237E12
    Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum Runout:
    Runout
    Specified Condition
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    If the runout is more than the maximum, replace the companion flange.


2. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

  1. C161834
    Using a dial indicator, measure the ring gear runout.

    Maximum runout:
    0.05 mm (0.00197 in.)

    If the runout is more than the maximum, replace the ring gear.


3. INSPECT DIFFERENTIAL RING GEAR BACKLASH

  1. C161835
    Using a dial indicator, measure the ring gear backlash.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    HINT:
    Measure at 3 or more positions around the circumference of the ring gear.

    If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


4. REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

  1. F044346E03
    Using SST and a hammer, unstake the nut.
    SST
    09930-00010  

  1. C161836E02
    Using SST to hold the companion flange, remove the nut.
    SST
    09330-00021   (09330-00030)


5. REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

  1. C161837E02
    Using SST, remove the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


6. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C162373E02
    Using SST, remove the oil seal from the differential carrier.
    SST
    09308-10010  


7. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

8. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C124133E03
    Using SST, remove the front bearing (inner race) from the drive pinion.
    SST
    09556-22010  
    If the front bearing is damaged or worn, replace the bearing.


9. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

  1. C161838
    Remove the 2 bolts and 2 adjusting nut locks.


10. REMOVE DIFFERENTIAL CASE ASSEMBLY

  1. C161903E02
    Place matchmarks on the bearing caps and differential carrier.

  1. Remove the 4 bolts, 2 bearing caps, 2 adjusting nuts and 2 bearings (outer race).

  1. C161275E01
    Remove the differential case from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races to show the location for reassembly.


11. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the differential drive pinion from the differential carrier.


12. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

13. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C116049E01
    Using SST and a press, press out the bearing (inner race).
    SST
    09950-00020  
    If either the drive pinion or ring gear is damaged, replace them as a set.


14. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

15. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C161839
    Using a brass bar and hammer, tap out the bearing (outer race).


16. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C162552
    Using a brass bar and hammer, tap out the bearing (outer race).


17. REMOVE DIFFERENTIAL RING GEAR

  1. C161840E02
    Place matchmarks on the ring gear and differential case.

  1. Remove the 12 ring gear set bolts.

  1. Using a plastic-faced hammer, tap on the ring gear to disconnect it from the differential case.


18. INSPECT RUNOUT OF DIFFERENTIAL CASE

HINT:
If the ring gear runout is at the maximum or less (refer to the "Inspect Runout of Differential Ring Gear" procedure), this inspection is not necessary.

  1. C161904
    Install the differential case to the differential carrier.

  1. Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.04 mm (0.00157 in.)

    If the runout is more than the maximum, replace the differential case and side bearings as a set.

  1. Remove the differential case from the differential carrier.


19. REMOVE REAR DIFFERENTIAL CASE BEARING

  1. C161842E02
    Using SST, remove the 2 side bearings (inner race) from the differential case.
    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00480)


20. DISASSEMBLE DIFFERENTIAL CASE

  1. C161843E05
    Place matchmarks on the differential case LH and RH.

  1. Remove the 8 bolts uniformly, a little at a time.

  1. Using a plastic-faced hammer, disconnect the differential case LH and RH.

  1. Remove the 2 side gear thrust washers, 2 side gears, spider, 4 pinion gears and 4 pinion gear thrust washers.

← REMOVAL (from Sep 2011)REASSEMBLY (from Sep 2011) →