2011-2013 Land Cruiser · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built from Sep 2011


1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY

  1. C161833
    Install a new gasket.

  1. Install the differential carrier with the 10 washers and 10 nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }

  1. C180071
    Connect the differential lock shift actuator and No. 4 transfer indicator switch clamps.

  1. Connect the breather hose.


2. CONNECT PROPELLER SHAFT ASSEMBLY

  1. C178527E01
    Align the matchmarks on the yoke and differential flange.

  1. Connect the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    88 N*m{ 900 kgf*cm , 65 ft.*lbf }


3. INSTALL REAR DIFFERENTIAL LOCK ACTUATOR PROTECTOR

  1. C174229
    Install the protector with the 2 nuts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }


4. INSTALL DIFFERENTIAL PROTECTOR ASSEMBLY

  1. C174228
    Attach the protector with the bolt and nut.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

  1. Connect the 2 connector clamps and wire harness clamp.

    NOTICE:
    Make sure the wire harness of the No. 4 transfer indicator switch fits inside the protector.


5. INSTALL REAR AXLE SHAFT
  1. Install the rear axle shaft (Click here).


6. ADD DIFFERENTIAL OIL

  1. D025304E27
    Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Front differential oil type and viscosity:
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent

    Rear Differential Oil Type and Viscosity:
    Item
    Oil Type and Viscosity
    w/o LSD
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    w/ LSD
    Toyota Genuine Differential gear oil LX 75W-85 GL-5 or equivalent

    Front differential capacity:
    1.85 to 1.95 liters (1.96 to 2.06 US qts., 1.63 to 1.71 Imp. qts.)

    Rear Differential Capacity:
    Item
    Specified Condition
    Standard
    4.15 to 4.25 liters (4.39 to 4.49 US qts., 3.66 to 3.74 Imp. qts.)
    w/ LSD
    4.10 to 4.20 liters (4.34 to 4.43 US qts., 3.60 to 3.69 Imp. qts.)
    w/ Differential lock

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    2. Install the engine under cover.

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

← REASSEMBLY (from Sep 2011)COMPONENTS (from Sep 2011) →