2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174123E02
    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Tighten the radiator drain cock plug by hand.


7. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A174196E03
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


8. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A243375
    Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.


9. REMOVE INTAKE MANIFOLD

  1. A162091E01
    Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.

  1. A162087
    Disconnect the 2 water by-pass hoses.

  1. Disconnect the throttle body connector.

  1. A184056
    Disconnect the No. 1 ventilation hose.

  1. A162082
    Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Disconnect the vacuum switching valve connector (for ACIS).

  1. A162089
    Remove the No. 1 engine cover sub-assembly.

  1. A238871
    Remove the No. 3 engine cover.

  1. A238834
    Disconnect the 3 wire clamps from the 3 wire brackets.

  1. A238832
    Remove the bolt and wire bracket from the intake manifold.

  1. A184053
    Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.


10. REMOVE VENTILATION HOSE ASSEMBLY

  1. A163820E02
    Remove the 2 bolts and ventilation hose from the intake manifold.


11. REMOVE NO. 1 V-BANK COVER BRACKET

  1. A177622
    Remove the 2 bolts and bracket.


12. REMOVE V-BANK COVER BOLT

  1. A177623
    Remove the cover bolt from the intake manifold.


13. REMOVE NO. 2 V-BANK COVER BRACKET SUB-ASSEMBLY

  1. A177624
    Remove the bolt and bracket.


14. REMOVE THROTTLE BODY ASSEMBLY

  1. A162080E01
    Remove the 4 bolts, throttle body and gasket.


15. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

  1. A184054
    Disconnect the 2 vacuum hoses from the vacuum switching valve.

  1. Remove the bolt and vacuum switching valve.


16. REMOVE PURGE VSV

  1. A168583
    Disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.


17. REMOVE WIRE HARNESS CLAMP BRACKET

  1. A177625
    Remove the 2 bolts and 2 wire harness clamp brackets.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →