2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

OPERATION CHECK

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

E132044E04

INITIAL CHECK FUNCTION
  1. Turn the engine switch on (IG).

  2. After 2 seconds or more have passed, turn the clearance sonar main switch ON. Then check the buzzer sounding condition.

    Buzzer sounding:
    1 +/-0.3 seconds

    HINT:
    1. If a malfunction is detected in the ultrasonic sensor circuits, the location of the malfunctioning sensor blinks on the display's vehicle graphic. However, after the sensor returns to normal, the display also returns to normal.
    2. When the engine switch is turned on (IG) while the clearance sonar main switch is ON, the buzzer will not sound.


MALFUNCTION OF MULTI-INFORMATION DISPLAY

  1. Ultrasonic sensor open circuit

    1. If there is an open circuit between the ultrasonic sensor and the ECU or a sensor is malfunctioning, the malfunction is displayed as shown in the illustration.
      B183988E01

      HINT:
      1. The example shows an open circuit in the No. 1 ultrasonic sensor (front left sensor).
      2. If a sensor has an open circuit, "Check Sonar" is displayed. Refer to "open circuit in front sensor is displayed as a result or self-check" in the problem symptoms table to inspect it.

  2. Ultrasonic sensor frozen

    1. If a sensor is covered with foreign matter, such as mud or snow, the affected sensor is displayed as shown in the illustration.
      B183990E01

      HINT:
      1. The example shows that the No. 1 ultrasonic sensor (front left sensor) is covered with foreign matter.
      2. If "Clean Sonar" is displayed, cleaning the foreign matter from the sensor will return the sensor to normal.


MALFUNCTION OF MULTI-DISPLAY

  1. Ultrasonic sensor open circuit

    1. If there is an open circuit between the ultrasonic sensor and the ECU or a sensor is malfunctioning, the malfunction is displayed as shown in the illustration.
      E161731E01

      HINT:
      1. This example shows an open circuit in the No. 2 ultrasonic sensor (rear right sensor).
      2. If a sensor has an open circuit, refer to "open circuit in rear sensor is displayed as a result of self-check" in the problem symptoms table to inspect it.

  2. Ultrasonic sensor frozen

    1. If a sensor is covered with foreign matter, such as mud or snow, the affected sensor is displayed as shown in the illustration.
      E161732E01

      HINT:
      1. The example shows that the No. 1 ultrasonic sensor (front left sensor) is covered with foreign matter.
      2. If "Clean sonar" is displayed, cleaning the foreign matter from the sensor will return the sensor to normal.


DETECTION RANGE MEASUREMENT AND DISPLAY CHECK

NOTICE:
Apply the parking brake securely so that the vehicle does not move.

  1. Turn the engine switch on (IG).

  2. Move the shift lever to R to check the No. 1 ultrasonic sensors, No. 2 ultrasonic sensors and No. 3 ultrasonic sensors.

  3. Move the shift lever to D and N to check the No. 1 ultrasonic sensors.

  4. Turn the clearance sonar main switch on.

  5. Move the φ60 mm (2.36 in.) pole around the sensor to measure the detection range of the sensor.

    NOTICE:
    1. These detection ranges are applicable when positioning the φ60 mm (2.36 in.) pole parallel or perpendicular to the ground.
    2. The ranges vary depending on the measuring method and type of obstacle (such as walls).
    3. For close-range and medium-range detection, the values shown are for when using a pole with a diameter of 60 mm (2.36 in.). For long-range detection, the values shown are for when using walls.
    4. The detection range of the resin bumper and steel bumper are not the same, as their installation positions are slightly different.


    1. No. 1 ultrasonic sensors detection range
      E162046E02

    2. No. 2 ultrasonic sensor detection range
      E162047E03

    3. No. 3 ultrasonic sensor detection range
      E160164E01

  6. When the ultrasonic sensors have detected an obstacle, check the multi-display, multi-information display and that the No. 1 clearance warning buzzer sounds with the clearance sonar main switch on.

    Operation Condition 
    Shift Lever Position
    Vehicle Speed
    Multi-display Detection, Multi-information Display Detection, Buzzer Detection
    No. 1 Ultrasonic Sensor
    No. 2 Ultrasonic Sensor
    No. 3 Ultrasonic Sensor
    P
    -
    Only perform check operation
    D, S, (N)
    9 km/h (5.6 mph) or less
    ○
    X
    X
    R
    No limit
    ○
    ○
    ○

    1. Check that the buzzer sounds with the clearance sonar main switch on as shown in the illustration.
      E132045E05

      No. 1 Ultrasonic Sensor Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 350 +/-40 mm (13.8 +/-1.57 in.)
      2. Medium-range detection
      350 +/-40 to 475 +/-50 mm (13.8 +/-1.57 to 18.7 +/-1.96 in.)
      3. Long-range detection
      475 +/-50 to 600 +/-60 mm (18.7 +/-1.96 to 23.6 +/- 2.36 in.)
      No. 2 Ultrasonic Sensor Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 300 +/-30 mm (11.8 +/-1.18 in.)
      2. Medium-range detection
      300 +/-30 to 375 +/-40 mm (11.8 +/-1.18 to 14.8 +/-1.57 in.)
      3. Long-range detection
      375 +/-40 to 600 +/-60 mm (14.8 +/-1.57 to 23.6 +/-2.36 in.)
      No. 3 Ultrasonic Sensor Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 350 +/-40 mm (13.8 +/-1.57 in.)
      2. Medium-range detection
      350 +/-40 to 450 +/-50 mm (13.8 +/-1.57 to 17.7 +/-1.96 in.)
      3. Long-range detection
      450 +/-50 to 600 +/-60 mm (17.7 +/-1.96 to 23.6 +/-2.36 in.)
      4. Maximum long-range detection
      600 +/-60 to 1500 +/-150 mm (23.6 +/-2.36 to 59.1 +/-5.91 in.)

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.

    2. Check the multi-information display and buzzer when the No. 1 ultrasonic sensors have detected an obstacle.

      Operation Condition 
      Engine Switch
      Clearance Sonar Main Switch
      Shift Lever Position
      Vehicle Speed
      on (IG)
      On
      D, N
      9 km/h (5.6 mph) or less
      B183992E01
      Multi-information Display 
      Detection Range
      Buzzer
      Number of Bars Displayed
      1. Close-range detection
      Sounds continuously
      1 (blinking)
      2. Medium-range detection
      Sounds intermittently
      (ON: 75 msec. / OFF: 75 msec.)
      2 (illuminated)
      3. Long-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 150 msec.)
      3 (illuminated)
      B181087E01
      Multi-display 
      Detection Range
      Buzzer
      Number of Bars Displayed
      1. Close-range detection
      Sounds continuously
      1 (red illumination)
      2. Medium-range detection
      Sounds intermittently
      (ON: 75 msec. / OFF: 75 msec.)
      2 (yellow illumination)
      3. Long-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 150 msec.)
      3 (yellow illumination)

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.

    3. Check the multi-information display and buzzer when the No. 2 ultrasonic sensors and No. 3 ultrasonic sensors have detected an obstacle.

      Operation Condition 
      Engine Switch
      Clearance Sonar Main Switch
      Shift Lever Position
      on (IG)
      On
      R
      B183993E01
      Multi-information Display 
      Detection Range
      Buzzer
      Number of Bars Displayed
      1. Close-range detection
      Sounds continuously
      1 (blinking)
      2. Medium-range detection
      Sounds intermittently
      (ON: 75 msec. / OFF: 75 msec.)
      2 (illuminated)
      3. Long-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 150 msec.)
      3 (illuminated)
      4. Maximum long-range detection
      (for rear center sensors)
      Sounds intermittently
      (ON: 150 msec. / OFF: 650 msec.)
      4 (illuminated)
      E144964E02
      Multi-display 
      Detection Range
      Buzzer
      Number of Bars Displayed
      1. Close-range detection
      Sounds continuously
      1 (red illumination)
      *: Illumination (red)
      2. Medium-range detection
      Sounds intermittently
      (ON: 75 msec. / OFF: 75 msec.)
      2 (yellow illumination)
      *: Blinking (yellow)
      3. Long-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 150 msec.)
      3 (yellow illumination)
      *: Blinking (yellow)
      4. Maximum long-range detection
      (for rear center sensors)
      Sounds intermittently
      (ON: 150 msec. / OFF: 650 msec.)
      4 (yellow illumination)
      *: Blinking (yellow)

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Jan 2012)OPERATION CHECK (from Jan 2012) →