2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1662/45 Indicator Light Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The indicator light circuit consists of the center airbag sensor and the combination meter.
When the center airbag sensor detects a malfunction in the SRS airbag system, the SRS warning light comes on to inform the driver. It also comes on when the source voltage drops, and automatically goes off in approximately 10 seconds after the source voltage returns to normal (DTC is not stored).
The SRS warning light comes on for 6 seconds after the ignition switch is turned to ON and goes off if the system is normal.
When an open circuit is detected, such as when the connector between the combination meter and the center airbag sensor is disconnected, the SRS warning light remains on even when approximately 6 seconds elapsed after the ignition switch is turned to ON.
DTC B1662/45 is stored when a malfunction is detected in the indicator light circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1662/45
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal, a short to ground signal or a short circuit to ground signal or a short circuit to B+ signal in the indicator light circuit for 2 seconds.
  2. A combination meter malfunction.
  3. A center airbag sensor malfunction.
  1. Combination meter assembly (SRS warning light)
  2. Center airbag sensor assembly
  3. Instrument panel wire

WIRING DIAGRAM

C159525E06

INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2. CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard Voltage:
    11 to 14 V



NG
CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK


3. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and combination meter.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

  1. C148471E09
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E47-21 (IG2) - E47-25 (E1)
    Ignition switch ON
    11 to 14 V
    E47-21 (IG2) - E47-26 (E2)
    Ignition switch ON
    11 to 14 V



NG
REPLACE HARNESS AND CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

  1. C173438E08
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the E7 connector from the combination meter.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-18 (IG+) - E7-15 (ET)
    Ignition switch ON
    11 to 14 V



NG
REPLACE HARNESS AND CONNECTOR
OK


6. CHECK SRS WARNING LIGHT (SHORT TO GROUND)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connector to the combination meter.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, SRS warning light goes off for approximately 10 seconds and then remains on.

    HINT:
    The primary check period is approximately 6 seconds after the ignition switch is turned ON.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← B1661/44 Roll Over Cut Off Indicator Malfunction (from Jan 2012)B1662/45 Indicator Light Circuit Malfunction (from Jan 2012) →