INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
![]() ![]() |
Install the protector with 2 new grommets.
Install the 2 screws.
| 2. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR |
- HINT:
- Use the same procedures described for the LH side.
| 3. INSTALL REAR BUMPER ARM BRACKET LH |
![]() ![]() |
Install the bumper arm bracket with the 2 bolts.
Connect the connector.
| 4. INSTALL REAR BUMPER ARM BRACKET |
![]() ![]() |
- HINT:
- Use the same procedure to install the bumper arm bracket on the other side.
Install the bumper arm bracket with the bolt.
| 5. INSTALL REAR NO. 2 BUMPER REINFORCEMENT |
![]() ![]() |
Install the bumper reinforcement with the 2 bolts.
| 6. INSTALL REAR BUMPER SIDE SUPPORT LH |
![]() ![]() |
Attach the 6 claws to install the bumper side support.
Install the 3 screws.
| 7. INSTALL REAR BUMPER SIDE SUPPORT RH |
- HINT:
- Use the same procedures described for the LH side.
| 8. INSTALL UPPER REAR BUMPER RETAINER LH |
![]() ![]() |
Attach the 2 clips to install the bumper retainer.
| 9. INSTALL UPPER REAR BUMPER RETAINER RH |
- HINT:
- Use the same procedures described for the LH side.
| 10. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH |
Connect the connector.

Attach the 2 clips to install the rear combination light.
Install the 2 bolts.
| 11. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH |
- HINT:
- Use the same procedures described for the LH side.
| 12. INSTALL REAR BUMPER COVER |
- HINT:
- For the rear bumper cover with tire carrier, use the procedures described below.
w/o TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:
Attach the 14 claws to install the bumper cover.
w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:
Connect the No. 2 frame wire connector and attach the 14 claws to install the bumper cover.
Install the 7 bolts, 6 screws and 2 clips.


Open the tail gate and install the 4 clips.


Close the tail gate.
| 13. INSTALL REAR NO. 1 BUMPER PLATE |
Attach the 20 claws to install the bumper plate.


| 14. INSTALL REAR QUARTER PANEL MUDGUARD LH |
![]() ![]() |
Install the mudguard with the clip.
Using a T30 "TORX" socket, install the 6 screws.
| 15. INSTALL REAR QUARTER PANEL MUDGUARD RH |
![]() ![]() |
Install the mudguard with the clip.
Using a T30 "TORX" socket, install the 7 screws.
| 16. INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier) |
Clean the threaded surfaces on the vehicle body with a non-residue solvent.
Apply adhesive to the threads of the 6 bolts.
- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the spare wheel carrier with the 6 bolts.
- Torque:
- 28.4 N*m{ 290 kgf*cm , 21 ft.*lbf }


Install the spare tire.
- Torque:
- 90 N*m{ 918 kgf*cm , 66 ft.*lbf }
| 17. INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier) |
![]() ![]() |
Attach the clip to install the cover.
Install the 2 nuts.
| 18. INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier) |
![]() ![]() |
Attach the 2 claws to install the bracket.










