2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE PINTLE HOOK ASSEMBLY

  1. B185550E02
    For vehicles with a spare tire installed to the underbody, remove the spare tire.
    Text in Illustration 
    *1
    Eyelet Pintle Hook
    *2
    Pintle Hook Bracket

  1. Remove the 4 nuts.

  1. Remove the 2 bolts, 2 eyelet pintle hooks, pintle hook assembly and pintle hook bracket.


2. REMOVE SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

B186194
  1. Detach the 2 claws and remove the bracket.


3. REMOVE SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

B186195
  1. Remove the 2 nuts.

  1. Detach the clip and remove the cover.


4. REMOVE SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)
  1. Remove the spare tire.

  1. Remove the 6 bolts and spare wheel carrier.

    B186196


5. REMOVE REAR QUARTER PANEL MUDGUARD LH

B180882
  1. Remove the clip.

  1. Using a T30 "TORX" socket, remove the 6 screws and mudguard.


6. REMOVE REAR QUARTER PANEL MUDGUARD RH

B180883
  1. Remove the clip.

  1. Using a T30 "TORX" socket, remove the 7 screws and mudguard.


7. REMOVE REAR NO. 1 BUMPER PLATE
  1. Put protective tape around the rear No. 1 bumper plate.

  1. Detach the 20 claws and remove the rear No. 1 bumper plate.

    B184213E02

    Text in Illustration 
    *1
    Protective Tape
    -
    -


8. REMOVE REAR BUMPER COVER

HINT:
For the rear bumper cover with tire carrier, use the procedures described below.

  1. Put protective tape around the rear bumper cover.

    B302240E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Open the tail gate and remove the 4 clips.

    B302241

  1. Close the tail gate.

  1. Remove the 7 bolts, 6 screws and 2 clips.

  1. Detach the 14 claws and remove the rear bumper cover.

    B302242

  1. w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:
    Disconnect the No. 2 frame wire connector.


9. REMOVE REAR COMBINATION LIGHT ASSEMBLY LH

  1. E244781E01
    Using a screwdriver wrapped with protective tape, detach the 6 claws and remove the 2 cover.
    Text in Illustration 
    *1
    Protective Tape

  1. E244782E01
    Put protective tape around the rear combination light assembly LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 2 bolts.

  1. Detach the 2 clips and remove the rear combination light assembly LH.

  1. Disconnect the connector.


10. REMOVE REAR COMBINATION LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


11. REMOVE REAR UPPER BUMPER RETAINER LH

  1. B181015
    Detach the 2 clips and remove the rear upper bumper retainer LH.


12. REMOVE REAR UPPER BUMPER RETAINER RH

HINT:
Use the same procedure described for the LH side.


13. REMOVE REAR BUMPER SIDE SUPPORT LH

  1. B181014
    Remove the 3 screws.

  1. Detach the 6 claws and remove the rear bumper side support LH.


14. REMOVE REAR BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure described for the LH side.


15. REMOVE REAR NO. 2 BUMPER REINFORCEMENT

  1. B185555
    Remove the 2 bolts and rear No. 2 bumper reinforcement.


16. REMOVE REAR BUMPER ARM BRACKET

  1. B181012
    Remove the bolt and rear bumper arm bracket.

    HINT:
    Use the same procedure to remove the rear bumper arm bracket on the other side.


17. REMOVE REAR BUMPER ARM BRACKET LH

  1. B181013
    Disconnect the connector.

  1. Remove the 2 bolts and rear bumper arm bracket LH.


18. REMOVE NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

  1. B190217
    Remove the 2 screws, 2 grommets and No. 2 luggage compartment side cover protector.


19. REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

HINT:
Use the same procedure described for the LH side.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (Sep 2011 – Dec 2011) →