2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE NO. 2 FRAME WIRE

  1. w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:

    1. Disconnect the 4 connectors.

    2. Detach the 12 clamps and remove the No. 2 frame wire.

      B302192

  1. w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:

    1. Disconnect the 6 connectors.

    2. Detach the 14 clamps and remove the No. 2 frame wire.

      B302172

  1. w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:

    1. Disconnect the 2 connectors.

    2. Detach the 13 clamps and remove the No. 2 frame wire.

      B302193


2. REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

  1. E244161
    Detach the 2 claws and remove the No. 1 ultrasonic sensor.

    HINT:
    1. Use the same procedure for all No. 1 ultrasonic sensors.
    2. The illustration shows the No. 1 ultrasonic sensor for the RH corner and back sensor LH and RH. The installation position of the No. 1 ultrasonic sensor for the LH corner is on the opposite side.


3. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

  1. E244162
    Detach the 2 claws and remove the No. 1 ultrasonic sensor retainer from the rear bumper cover.

    HINT:
    1. Use the same procedure to remove the No. 1 ultrasonic sensor retainer on the other side.
    2. The illustration shows the No. 1 ultrasonic sensor retainer for the RH corner. The vertical orientation of the No. 1 ultrasonic sensor retainers for the LH corner is opposite that of the image shown in the illustration.


4. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

  1. E244159
    Detach the 2 claws and remove the No. 2 ultrasonic sensor retainer from the rear bumper cover.

    HINT:
    Use the same procedure to remove the No. 2 ultrasonic sensor retainer on the other side.


5. REMOVE REAR BUMPER ENERGY ABSORBER

  1. B302173
    Detach the 8 claws and remove the rear bumper energy absorber.


6. REMOVE REFLEX REFLECTOR ASSEMBLY LH (w/o Rear Fog Light)

  1. B302187
    Remove the 2 nuts.

  1. Detach the claw and remove the reflex reflector assembly LH.


7. REMOVE REFLEX REFLECTOR ASSEMBLY RH (w/o Rear Fog Light)

HINT:
Use the same procedure described for the LH side.


8. REMOVE REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light)

  1. E155858
    Remove the 2 nuts.

  1. Disconnect the connectors.

  1. Detach the claw and remove the fog light.


9. REMOVE REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light)

HINT:
Use the same procedure described for the LH side.


10. REMOVE REAR NO. 2 STEP COVER

  1. B185558
    Detach the 10 claws and remove the rear No. 2 step cover.


11. REMOVE REAR NO. 2 BUMPER SIDE BRACKET (w/ Tire Carrier)

  1. B185559E02
    Remove the 2 screws.
    Text in Illustration 
    *1
    Rear No. 2 Bumper Side Bracket
    *2
    Rear No. 3 Bumper Side Bracket

  1. Detach the 3 claws and 2 clips, and remove the rear No. 2 bumper side bracket and rear No. 3 bumper side bracket.

← DISASSEMBLY (Sep 2011 – Dec 2011)REASSEMBLY (Sep 2011 – Dec 2011) →