2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. When removing window frame moulding, heat the vehicle body and window frame moulding using a heat light.

Standard Heating Temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Window Frame Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and window frame moulding excessively.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH

  1. B180820
    Detach the clip and claw, remove the front lower door frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B180816
    Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH

B180817
  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.


5. REMOVE DOOR ASSIST GRIP COVER LH

  1. B180819
    Using a moulding remover, detach the 8 claws and remove the door assist grip cover.


6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B180821
    Remove the 3 screws.

  1. Remove the 13 clips, 4 claws and trim board.

  1. Disconnect the connector.

  1. B180822
    Disconnect the 2 cables from the inside handle.


7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B180573E01
  1. w/ Power Mirror Control System:

    1. Disconnect the connector labeled A.

    2. Detach the clamp.

  1. Remove the 3 nuts and claw.

  1. Remove the outer rear view mirror.


8. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B182874
    Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the service hole cover.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH

  1. B180828
    Detach the 4 claws by pulling the weatherstrip upward to remove the weatherstrip.


10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Driver Side:
    Temporarily install the multiplex network master switch.

  1. Passenger Side:
    Temporarily install the power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the door glass until the bolts appear in the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B180832
    Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.

  1. B180833
    Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. Driver Side:
    Remove the multiplex network master switch.

  1. Passenger Side:
    Remove the power window regulator switch assembly.


11. REMOVE FRONT DOOR GLASS RUN LH

  1. B180838
    Remove the front door glass run.


12. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

B182606E01
  1. Put protective tape around the belt moulding.

  1. B182604
    Detach the claw and remove the belt moulding.


13. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

B182608E01
  1. Put protective tape around the window frame moulding.

  1. Detach the clip and remove the double-sided tape to remove the window frame moulding.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →