INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- When installing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.
- Standard Heating Temperature:
Item
|
Temperature
|
Vehicle Body
|
40 to 60°C (104 to 140°F)
|
Window Frame Moulding
|
20 to 30°C (68 to 86°F)
|
- NOTICE:
- Do not heat the vehicle body and window frame moulding excessively.
| 1.
INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH |
 |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body surface.
Wipe off any tape adhesive residue with cleaner.
Install a new window frame moulding.
Using a heat light, heat a new window frame moulding and the vehicle body surface.
Remove the peeling paper from the face of the window frame moulding.
- HINT:
- After removing the peeling paper, keep the exposed adhesive free from foreign matter.
- Attach the clip and double-sided tape to install the window frame moulding.
- HINT:
- Press the window frame moulding firmly to install it.
| 2.
INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH
|
 |
Attach the claw to install the belt moulding.
| 3.
INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
|
 |
- Slide the rear door glass sub-assembly as shown in the illustration to install it.
| 4.
INSTALL REAR DOOR QUARTER WINDOW GLASS LH
|
 |
- Install the quarter glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
| 5.
INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
|
 |
- Install the rear door rear lower window frame with the 2 bolts and screw.
| 6.
INSTALL REAR DOOR GLASS RUN LH
|
 |
- Install the rear door glass run.
| 7.
INSTALL REAR DOOR SERVICE HOLE COVER LH
|
 |
Apply butyl tape to the door.
- Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.
- NOTICE:
- When installing the service hole cover, pull the links and connectors through the service hole cover.
- There should be no wrinkles or folds after attaching the service hole cover.
- After attaching the service hole cover, check the sealing quality.
- Connect the 2 connectors.
Attach the 6 clamps.
- Install the bolt as shown in the illustration.
-
Torque:
- 8.4 N*m{
86 kgf*cm
, 74 in.*lbf
}
| 8.
INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH
|
 |
- Install the rear inner door glass weatherstrip to the door panel.
| 9.
INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
|
 |
Connect the connector.
- Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.
- Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly.
Install the 3 screws.
| 10.
INSTALL ASSIST GRIP COVER LH
|
 |
- Attach the 9 claws to install the door assist grip cover to the door trim panel.
| 11.
INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH
|
 |
Connect the connector.
- Attach the 7 claws to install the armrest base panel.
| 12.
INSTALL REAR DOOR INSIDE HANDLE BEZEL LH
|
 |
- Attach the 4 claws to install the bezel.
| 13.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).