2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Sep 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedures for LHD and RHD vehicles.
  2. The procedures listed below are for LHD vehicles.


1. REMOVE FRONT SEAT ASSEMBLY LH
  1. Remove the front seat assembly LH (Click here).


2. REMOVE VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)

B180752
  1. Using a screwdriver, detach the 2 claws and remove the vertical adjuster cover LH.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)

B180753
  1. Remove the 2 screws and vertical adjusting handle LH.


4. REMOVE VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)

B180754
  1. Remove the snap ring and vertical seat adjuster knob.


5. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B180755E01
  1. Lift the reclining adjuster release handle LH.

  1. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

    HINT:
    Tape the screwdriver tip before use.


6. REMOVE FRONT SEAT CUSHION SHIELD LH

  1. B180757
    w/ Seatback Board:
    Disconnect the 2 rubber bands from the 2 hooks.

  1. B180756
    w/o Seatback Board:
    Disconnect the rubber band from the 2 hooks.

  1. B180758E02
    for 4 Way Seat Type:

    1. Remove the 2 screws.

    2. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.

  1. B180759E01
    for 8 Way Seat Type:

    1. Remove the 3 screws.

    2. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.

  1. w/ Lumbar Support:
    Disconnect the lumbar switch connector.


7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Disconnect the connectors and detach the clamps.

  1. B189677
    Remove the nut and front seat inner belt assembly.


8. REMOVE FRONT INNER SEAT CUSHION SHIELD LH

B180761
  1. Remove the screw.

  1. Detach the claw and clip, and then remove the front inner seat cushion shield LH.


9. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

B180711
  1. Remove the 2 screws.

  1. Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.


10. REMOVE FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)

B180712
  1. Detach the 4 claws and remove the 2 front seat headrest supports.


11. REMOVE SEATBACK COVER WITH PAD

  1. w/ Seatback Board:

    1. B191295E01
      Remove the 3 hog rings and detach the 9 hooks.

    2. B180716
      w/ Front Seat Side Airbag:
      Remove the nut and seatback cover bracket from the seat frame.

  1. w/o Seatback Board:

    1. B180766
      Remove the 3 hog rings.

    2. B180767
      Open the 2 fasteners, and then open the front separate type seatback cover.

    3. B180716
      w/ Front Seat Side Airbag:
      Remove the nut and seatback cover bracket from the seat frame.

    4. B180768
      Detach the 4 claws and remove the 2 front seat headrest supports.

  1. Remove the seatback cover with pad from the seatback frame.


12. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH

  1. B102194
    Detach the 5 clamps and disconnect the wire harness.

  1. B102198
    Detach the 2 clamps and disconnect the wire harness.

  1. Remove the 2 nuts and front seat airbag assembly LH.

    CAUTION:
    Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.

← ON-VEHICLE INSPECTION (from Jan 2012)INSTALLATION (from Sep 2011) →