2011-2013 Land Cruiser · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

B180697E01
  1. Apply protective tape around the cushion shield.

  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.


2. REMOVE RECLINING POWER SEAT SWITCH KNOB

B180698E01
  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE FRONT SEAT CUSHION SHIELD LH

B180699
  1. Disconnect the 2 rubber bands from the 2 hooks.

  1. Remove the 2 screws.

  1. B180700
    Remove the 3 screws.

  1. Detach the 2 claws and remove the cushion shield.

  1. for Driver Side:
    Disconnect the lumbar switch connector.


4. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

B180701
  1. Remove the screw.

  1. Detach the claw and remove the cushion shield.


5. REMOVE LUMBAR SWITCH (for Driver Side)

B180702
  1. Remove the 2 screws and switch.


6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Disconnect the connectors and detach the clamps.

  1. B185874
    Remove the nut and front seat inner belt assembly.


7. REMOVE FRONT INNER SEAT CUSHION SHIELD LH

B180703
  1. Remove the screw.

  1. Detach the 2 claws and clip, and then remove the cushion shield.


8. REMOVE FRONT POWER SEAT SWITCH LH

B180704
  1. w/ Seat Position Memory System:
    Disconnect the 2 connectors.

  1. w/o Seat Position Memory System:
    Disconnect the connector.

  1. Remove the 3 screws and switch.


9. REMOVE SEAT CUSHION COVER WITH PAD

  1. B180705
    Using a clip remover, remove the 2 clips.

  1. B180706
    Disconnect the seat heater connector and detach the 2 wire harness clamps.

  1. B180707
    Disconnect the seat heater control connector and detach the wire harness clamp.

  1. B180765
    for Front Passenger Side:
    Detach the 2 clamps and remove the connector holder.

  1. B180708
    Bend the 2 seat frame claws upward.

  1. Detach the hooks and remove the seat cushion cover with pad.


10. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER

  1. B180709
    Remove the hog rings and front seat cushion cover.


11. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

  1. B180710
    Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.


12. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH

B180711
  1. Remove the 2 screws.

  1. Move the seatback board in the direction of the arrow to detach the 2 hooks and remove the seatback board.


13. REMOVE FRONT SEAT HEADREST SUPPORT

B180712
  1. Using a screwdriver, detach the 4 claws and remove the 2 headrest supports.


14. REMOVE SEATBACK COVER WITH PAD

  1. B180713E01
    Remove the hog rings and detach the 9 hooks.

  1. B180716
    Remove the nut and seatback cover bracket from the seat frame.

  1. Remove the seatback cover with pad.


15. REMOVE FRONT SEPARATE TYPE SEATBACK COVER

  1. B180717
    Disconnect the seatback cover bracket from the seatback pad.

  1. B180718E01
    Remove the hog rings.

  1. Detach the fastening tape and remove the seatback cover.


16. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

  1. B180719
    Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.


17. REMOVE INSIDE RECLINING ADJUSTER COVER LH

B180721
  1. Detach the wire harness clamp.

  1. Remove the 2 screws.

  1. Detach the claw and remove the cover.


18. REMOVE INSIDE RECLINING ADJUSTER COVER RH
  1. Detach the wire harness clamp.

  1. Remove the 2 screws.

  1. Detach the claw and remove the cover.


19. REMOVE OUTSIDE RECLINING ADJUSTER COVER LH

B180720
  1. Remove the screw and detach the claw, and then remove the reclining adjuster cover.


20. REMOVE OUTSIDE RECLINING ADJUSTER COVER RH
  1. Remove the screw and detach the claw, and then remove the reclining adjuster cover.


21. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)

  1. B293541E01
    Remove the 4 springs.

  1. Remove the cable clamp and disconnect the active headrest cable from the seatback spring.

  1. Detach the 4 hooks and remove the seatback spring.

  1. B180724
    Disconnect the lumbar support adjuster connector.

  1. Remove the 2 screws and lumbar support adjuster.

  1. B180725
    Detach the 3 claws and remove the bush from the seat frame.


22. REMOVE LOWER ACTIVE HEADREST UNIT

B180726
  1. Remove the 6 nuts, and then remove the lower active headrest unit together with the upper active headrest unit.


23. REMOVE UPPER ACTIVE HEADREST UNIT

B180727
  1. Remove the nut and cable clamp to remove the upper active headrest unit from the lower active headrest unit.


24. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH

B180722
  1. Remove the screw.

  1. Detach the hook and remove the lower cushion shield.


25. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH
  1. Remove the screw.

  1. Detach the hook and remove the lower cushion shield.


26. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

B180728
  1. Disconnect the seat heater control connector and detach the clamp.

  1. Using a screwdriver, detach the claw and remove the seat heater control.


27. REMOVE SEAT POSITION SENSOR

  1. B181656
    Using a T30 "TORX" socket wrench, remove the screw and seat position sensor with sensor protector.

  1. Disconnect the connector.

  1. C108775E04
    Remove the seat slide position sensor protector from the seat position sensor.


28. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH

  1. B102196
    Detach the 5 clamps and disconnect the wire harness.

  1. B102199
    Detach the 2 clamps and disconnect the wire harness.

  1. Remove the 2 nuts and front seat airbag assembly LH.

    CAUTION:
    Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.


29. REMOVE FRONT SEAT WIRE LH
  1. Detach the wire harness clamps.

  1. Detach the claw and remove the front seat wire.

← REMOVAL (from Jan 2012)DISASSEMBLY (from Jan 2012) →