2011-2013 Land Cruiser · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. INSTALL FRONT SEAT WIRE LH
  1. Attach the claw to install the front seat wire.

  1. Attach the wire harness clamps.


2. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

CAUTION:
Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.

  1. B102199
    Install the front seat airbag assembly with 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Attach the 2 clamps to connect the wire harness.

  1. B102196
    Attach the 5 clamps to connect the wire harness.


3. INSTALL SEAT POSITION SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. C107067E04
    Using a 1.0 mm (0.0393 in.) feeler gauge, install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Using a T30 "TORX" socket wrench, install the seat position sensor with the screw.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.

  1. Install the seat slide position sensor protector to the seat position sensor.


4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

B180728
  1. Attach the claw to install the seat heater control.

  1. Attach the clamp and connect the seat heater control connector.


5. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

B180722
  1. Attach the hook to install the lower cushion shield.

  1. Install the screw.


6. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
  1. Attach the hook to install the lower cushion shield.

  1. Install the screw.


7. INSTALL UPPER ACTIVE HEADREST UNIT

B180727
  1. Install the upper active headrest unit to the lower active headrest unit with the cable clamp and nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


8. INSTALL LOWER ACTIVE HEADREST UNIT

B180726
  1. Install the lower active headrest unit together with the upper active headrest unit with the 6 nuts.

    Torque:
    Upper active headrest unit:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Lower active headrest unit:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


9. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)

  1. B180725
    Attach the 3 claws to install the bush to the seat frame.

  1. B180724
    Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.

  1. B293541E01
    Attach the 4 hooks to install the seatback spring.

  1. Connect the active headrest cable with the cable clamp.

  1. Install the 4 springs.


10. INSTALL OUTSIDE RECLINING ADJUSTER COVER RH

B180720
  1. Attach the claw to install the reclining adjuster cover.

  1. Install the screw.


11. INSTALL OUTSIDE RECLINING ADJUSTER COVER LH
  1. Attach the claw to install the reclining adjuster cover.

  1. Install the screw.


12. INSTALL INSIDE RECLINING ADJUSTER COVER RH

B180721
  1. Attach the claw to install the cover.

  1. Install the 2 screws.

  1. Attach the wire harness clamp.


13. INSTALL INSIDE RECLINING ADJUSTER COVER LH
  1. Attach the claw to install the cover.

  1. Install the 2 screws.

  1. Attach the wire harness clamp.


14. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new tack pins.

    B180729E01


15. INSTALL FRONT SEPARATE TYPE SEATBACK COVER

  1. B180730E01
    Attach the fastening tape to install the seatback cover.

  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B180731
    Connect the seatback cover bracket to the seatback pad.


16. INSTALL SEATBACK COVER WITH PAD
  1. Install the seatback cover with pad to the seatback frame.

  1. B180716
    Install the seatback cover bracket to the seat frame with the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    CAUTION:
    After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

  1. B180713E01
    Attach the 9 hooks.

  1. Using hog ring pliers, install new hog rings to the seat frame.


17. INSTALL FRONT SEAT HEADREST SUPPORT
  1. Attach the 4 claws to install the 2 headrest supports.


18. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

B182646
  1. Move the seatback board in the direction of the arrow to attach the 2 hooks and install the seatback board.

  1. Install the 2 screws.


19. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with new tack pins.

    B180732E01


20. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

B180733E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


21. INSTALL SEAT CUSHION COVER WITH PAD

  1. B180708
    Attach the hooks to install the seat cushion cover with pad.

  1. Bend the 2 seat frame claws downward.

  1. B180707
    Connect the seat heater control connector and attach the wire harness clamp.

  1. B180765
    for Front Passenger Side:
    Attach the 2 clamps to install connector holder.

  1. B180706
    Connect the seat heater connector and attach the 2 wire harness clamps.

  1. B180705
    Install the 2 clips.


22. INSTALL FRONT POWER SEAT SWITCH LH

B180704
  1. Install the switch with the 3 screws.

  1. w/ Seat Position Memory System:
    Connect the 2 connectors.

  1. w/o Seat Position Memory System:
    Connect the connector.


23. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

B180703
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.


24. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

B185875E01
  1. Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

  1. Connect the connectors and attach the clamps.


25. INSTALL LUMBAR SWITCH (for Driver Side)

B180702
  1. Install the lumbar switch with the 2 screws.


26. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

B180701
  1. Attach the claw to install the cushion shield.

  1. Install the screw.


27. INSTALL FRONT SEAT CUSHION SHIELD LH

  1. B180700
    for Driver Side:
    Connect the lumbar switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.

  1. B180699
    Install the 2 screws.

  1. Connect the 2 rubber bands to the 2 hooks.


28. INSTALL RECLINING POWER SEAT SWITCH KNOB

B180734
  1. Attach the 2 claws to install the knob.


29. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

B180735
  1. Attach the 2 claws to install the knob.

← DISASSEMBLY (from Jan 2012)REASSEMBLY (from Jan 2012) →