INSTALLATION
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH |
 |
- Install the lumbar support adjuster assembly LH with the 2 screws.
Connect the connector.
- Attach the 4 hooks to install the seatback spring.
Text in Illustration
*1
|
Cable Clamp
|
*2
|
Hook
|
Install the 4 springs.
Connect the active headrest cable to the seatback spring with the cable clamp.
| 2.
INSTALL FRONT SEATBACK PROTECTOR
|
 |
Apply double-sided tape as shown in the illustration.
Text in Illustration
*1
|
Double-sided tape
|
Install the front seatback protector.
| 3.
INSTALL SEATBACK COVER WITH PAD |
 |
Attach the hooks to install the seatback cover with pad.
Text in Illustration
*1
|
Hog Ring
|
*2
|
Hog Ring Pliers
|
- Attach the seatback cover bracket with the nut.
Text in Illustration
*1
|
Seatback Cover Bracket
|
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
Using hog ring pliers, install new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- w/o Climate Control Seat System:
Connect the connector and attach the 2 wire harness clamps.
- w/ Climate Control Seat System:
Connect the 2 connectors and attach the 4 wire harness clamps.
| 4.
INSTALL FRONT SEAT HEADREST SUPPORT
|
 |
Attach the 4 claws to install the 2 front seat headrest supports.
| 5.
INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)
|
 |
Attach the 4 hooks to install the seat climate control controller LH.
Attach the 2 claws to connect the seat climate control blower LH.
| 6.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH
|
 |
Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
Install the 2 screws.
| 7.
INSTALL FRONT INNER SEAT CUSHION SHIELD LH
|
 |
Attach the 2 claws and clip to install the front inner seat cushion shield LH.
Install the screw.
| 8.
INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
|
 |
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.
Connect the connectors and attach the clamps.
| 9.
INSTALL FRONT SEAT CUSHION SHIELD LH
|
 |
for Driver Side:
Connect the connector.
- Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.
Install the 3 screws.
- Connect the 2 rubber bands.
Install the 2 screws.
| 10.
INSTALL RECLINING POWER SEAT SWITCH KNOB
|
 |
Attach the 2 claws to install the reclining power seat switch knob.
| 11.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
|
 |
Attach the 2 claws to install the slide and vertical power seat switch knob.
| 12.
INSTALL FRONT SEAT ASSEMBLY LH |
 |
(Click here)