2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
  1. Remove the rear No. 1 seat assembly (Click here).


2. REMOVE SEAT ADJUSTER BOLT COVER

B181163
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

B181164
  1. Remove the screw and release handle.


4. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B181165E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cover.


5. REMOVE REAR NO. 1 SEAT RECLINING COVER LH

B181166
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


6. REMOVE UPPER SEAT TRACK RAIL COVER LH

B181168
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


7. REMOVE UPPER SEAT TRACK RAIL COVER RH

B181169
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER

  1. B181170
    Remove the 4 screws and detach the 3 claws.

  1. B181171
    Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.


9. REMOVE REAR NO. 2 SEAT PROTECTOR

  1. B182658
    w/ Rear Seat Side Airbag:
    Detach the claw and remove the wire harness connector.

  1. w/ Seat Heater System:
    Detach the claw and remove the wire harness connector.

  1. B184060
    Using a clip remover, remove the clip.

  1. Detach the claw and remove the seat protector from the seat hinge.

  1. Detach the 2 claws, open the protector and remove the wire harness.


10. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

B181174
  1. Remove the 2 nuts and hinge.


11. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B181175
  1. w/ Rear Seat Side Airbag:
    Detach the wire harness clamp.

  1. w/ Seat Heater System:
    Detach the wire harness clamp.

  1. Remove the 2 nuts and hinge.

  1. B181176
    Detach the cable clamp and disconnect the cable.


12. REMOVE REAR SEAT COVER

  1. B181177
    Detach the 12 claws.

  1. B181179
    Remove the 3 screws.

  1. Detach the 2 claws and remove the cover.


13. REMOVE REAR UNDER SIDE COVER LH

B181178
  1. Remove the 5 screws.

  1. Detach the clip and 2 claws, and remove the cover.


14. REMOVE REAR SEAT UNDER TRAY COVER RH

B181181
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


15. REMOVE SEAT CUSHION COVER WITH PAD
  1. w/ Rear Seat Side Airbag:

    1. Detach the side airbag wire harness clamps.

    2. Remove the side airbag wire harness through the hole in the seat cushion.

  1. w/ Seat Heater System:

    1. B184061
      Disconnect the 2 seat heater connectors.

    2. B184058
      Remove the seatback heater wire harness through the hole in the seat cushion.

  1. Remove the seat cushion cover with pad.


16. REMOVE REAR SEATBACK COVER

B181188E01
  1. Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


17. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH

B181189
  1. Detach the 2 claws on the top of the board.

  1. Pull up the board to detach the 2 claws on the bottom of the board and remove it.


18. REMOVE REAR SEAT HEADREST ASSEMBLY

19. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B181190
  1. Detach the 4 claws and remove the 2 supports.


20. REMOVE SEATBACK COVER WITH PAD

  1. B181191
    Remove the hog rings.

  1. B181192
    w/ Rear Seat Side Airbag:

    1. Remove the cap nut and seatback cover bracket from the seat frame.

    2. Remove the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:

    1. B184853E01
      Cut the cable tie and disconnect the seatback heater wire harness.

    2. B184854
      Remove the seatback heater wire harness through the hole in the seatback.

  1. Remove the seatback cover with pad.


21. REMOVE REAR SEPARATE TYPE SEATBACK COVER

  1. B181193
    w/ Rear Seat Side Airbag:
    Disconnect the seatback cover bracket from the seatback pad.

  1. B181194
    Remove the hog rings and rear seatback cover.


22. REMOVE REAR SEATBACK HEATER ASSEMBLY

B181195
  1. Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →