REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1.
REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
 |
Remove the rear No. 1 seat assembly (Click here).
| 2.
REMOVE SEAT ADJUSTER BOLT COVER
|
 |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 3.
REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
|
 |
Remove the screw and release handle.
| 4.
REMOVE REAR NO. 1 SEAT RECLINING COVER RH
|
 |
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the cover.
| 5.
REMOVE REAR NO. 1 SEAT RECLINING COVER LH
|
 |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 6.
REMOVE UPPER SEAT TRACK RAIL COVER LH
|
 |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 7.
REMOVE UPPER SEAT TRACK RAIL COVER RH
|
 |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 8.
REMOVE REAR NO. 2 SEAT LEG SIDE COVER
|
 |
- Remove the 4 screws and detach the 3 claws.
- Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.
| 9.
REMOVE REAR NO. 2 SEAT PROTECTOR
|
 |
- w/ Rear Seat Side Airbag:
Detach the claw and remove the wire harness connector.
w/ Seat Heater System:
Detach the claw and remove the wire harness connector.
- Using a clip remover, remove the clip.
Detach the claw and remove the seat protector from the seat hinge.
Detach the 2 claws, open the protector and remove the wire harness.
| 10.
REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
|
 |
Remove the 2 nuts and hinge.
| 11.
REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
|
 |
w/ Rear Seat Side Airbag:
Detach the wire harness clamp.
w/ Seat Heater System:
Detach the wire harness clamp.
Remove the 2 nuts and hinge.
- Detach the cable clamp and disconnect the cable.
| 12.
REMOVE REAR SEAT COVER
|
 |
- Detach the 12 claws.
- Remove the 3 screws.
Detach the 2 claws and remove the cover.
| 13.
REMOVE REAR UNDER SIDE COVER LH
|
 |
Remove the 5 screws.
Detach the clip and 2 claws, and remove the cover.
| 14.
REMOVE REAR SEAT UNDER TRAY COVER RH
|
 |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 15.
REMOVE SEAT CUSHION COVER WITH PAD
|
 |
w/ Rear Seat Side Airbag:
Detach the side airbag wire harness clamps.
Remove the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
- Disconnect the 2 seat heater connectors.
- Remove the seatback heater wire harness through the hole in the seat cushion.
Remove the seat cushion cover with pad.
| 16.
REMOVE REAR SEPARATE TYPE SEAT CUSHION COVER
|
 |
- Detach the 3 pieces of fastening tape.
- Remove the hog rings and cover.
| 17.
REMOVE REAR SEAT CUSHION HEATER ASSEMBLY |
 |
Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.