INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.
| 1.
INSTALL FRONT DOOR INSIDE LOCKING LH CABLE ASSEMBLY
|
 |
- Install the front door inside locking cable.
- Attach the 3 claws.
| 2.
INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
|
 |
- Install the front door lock remote control cable.
| 3.
INSTALL FRONT DOOR LOCK ASSEMBLY LH |
 |
Apply MP grease to the sliding parts of the front door lock assembly.
Insert the front door lock open rod to the front door lock assembly.
Make sure that the front door lock open rod is securely connected to the front door lock assembly.
Using a T30 "TORX" wrench, install the door lock with the 3 screws.
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
| 4.
INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH
|
 |
- Attach the 2 claws to install the front door outside handle cover to the front door lock cylinder.
- Using a T30 ''TORX'' socket, install the cover (with the door lock cylinder) with the screw.
-
Torque:
- 4.0 N*m{
41 kgf*cm
, 35 in.*lbf
}
Install the hole plug.
| 5.
INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
|
 |
- Install the frame with the bolt.
| 6.
INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION
|
 |
Clean the installation surface.
Using a heat light, heat the installation surface.
- HINT:
- When installing the door stiffener cushion, heat the vehicle body and door stiffener cushion using a heat light.
- Standard Heating Temperature:
Item
|
Temperature
|
Door Stiffener Cushion
|
20 to 30°C (68 to 86°F)
|
Vehicle Body
|
40 to 60°C (104 to 140°F)
|
- NOTICE:
- Do not heat the back door garnish and vehicle body excessively.
Remove the double-sided tape from the installation surface.
Wipe off any tape adhesive residue with cleaner.
Install a new door stiffener cushion.
Using a heat light, heat a new door stiffener cushion and the installation surface.
- HINT:
- When installing the door stiffener cushion, heat the vehicle body and door stiffener cushion using a heat light.
- Standard Heating Temperature:
Item
|
Temperature
|
Door Stiffener Cushion
|
20 to 30°C (68 to 86°F)
|
Vehicle Body
|
40 to 60°C (104 to 140°F)
|
- NOTICE:
- Do not heat the back door garnish and vehicle body excessively.
Remove the peeling paper from the face of the door stiffener cushion.
- HINT:
- After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Attach the 2 clamps and double-sided tape to install the door stiffener cushion.
- HINT:
- Press the door stiffener firmly to install it.
- Install the 2 bolts.
| 7.
INSTALL FRONT DOOR SERVICE HOLE COVER LH
|
 |
- Apply butyl tape to the door.
Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.
- NOTICE:
- When installing the service hole cover, pull the links and connectors through the service hole cover.
- There should be no wrinkles or folds after attaching the service hole cover.
- After attaching the service hole cover, check the sealing quality.
- Connect the 2 connectors.
Attach the 9 clamps.
Install the bolt as shown in the illustration.
-
Torque:
- 8.4 N*m{
86 kgf*cm
, 74 in.*lbf
}
| 8.
INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
|
 |
Connect the connector.
- Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.
- Attach the 4 claws and 13 clips to install the front door trim board sub-assembly.
Install the 3 screws.
| 9.
INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
|
 |
- Connect the connector.
Attach the claw of the courtesy light to the front door trim.
| 10.
INSTALL DOOR ASSIST GRIP COVER LH
|
 |
- Attach the 8 claws to install the door assist grip cover to the door trim panel.
| 11.
INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
|
 |
- Attach the 4 claws to install the bezel.
| 12.
INSTALL FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH
|
 |
Connect the connector.
- Attach the 5 claws to install the armrest base panel.
| 13.
INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH
|
 |
- Attach the clip and claw, and install the front door lower frame bracket garnish.
| 14.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 15.
CHECK SRS WARNING LIGHT |
 |
Check the SRS warning light (Click here).