2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH

  1. B180820
    Detach the clip and claw, remove the front lower door frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B180816
    Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH

B180817
  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.


5. REMOVE DOOR ASSIST GRIP COVER LH

  1. B180819
    Using a moulding remover, detach the 8 claws and remove the door assist grip cover.


6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155940
    Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.


7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B180821
    Remove the 3 screws.

  1. Remove the 13 clips, 4 claws and trim board.

  1. Disconnect the connector.

  1. B180822
    Disconnect the 2 cables from the inside handle.


8. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B182874
    Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the service hole cover.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION

  1. B183088
    Remove the 2 bolts.

  1. Detach the 2 clamps and door stiffener cushion.


10. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  1. B180840
    Remove the bolt and rear lower frame.


11. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

  1. B180841
    Remove the hole plug.

  1. Using a T30 "TORX" wrench, loosen the screw and remove the cover with the door lock cylinder installed.

  1. B180845
    Detach the 2 claws and remove the front door outside handle cover.


12. REMOVE FRONT DOOR LOCK ASSEMBLY LH

  1. B180842
    Using a T30 "TORX" wrench, remove the 3 screws.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


13. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180843
    Remove the front door lock remote control cable assembly.


14. REMOVE FRONT DOOR INSIDE LOCKING LH CABLE ASSEMBLY

  1. B180846
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B180847
    Remove the front door inside locking cable assembly.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →