2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


2. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

  1. B181910
    Remove the clip.

  1. Remove the screw.

  1. Detach the 8 claws.

  1. Remove the panel pad and disconnect the connectors and 2 clamps.


5. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


7. REMOVE NO. 1 LOWER INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


8. REMOVE NO. 1 SWITCH HOLE BASE

B180298
  1. Detach the 4 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole cover.


9. REMOVE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

  1. E248902E01
    Detach the 2 claws and remove the back sonar or clearance sonar switch assembly.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (Sep 2011 – Dec 2011) →