2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Driver Side Knee Airbag)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B292994E01
  1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.


3. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

B292995
  1. Remove the clip and screw.

  1. Detach the 8 claws.

  1. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.


4. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


5. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


7. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


8. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Detach the 2 claws and disconnect the DLC3.

  1. Remove the 5 bolts and lower instrument panel.


9. REMOVE NO. 1 SWITCH HOLE BASE

B180298
  1. Detach the 4 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole cover.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


11. REMOVE SEAT BELT CONTROL ECU

E155216
  1. Disconnect the 2 connectors.

  1. Remove the 2 nuts and remove the seat belt control ECU together with the certification ECU.

  1. E155217
    Remove the bolt and seat belt control ECU from the certification ECU.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →