INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1.
INSTALL FUEL TANK TO FILLER PIPE HOSE |
 |
- Install the hose to the fuel sub tank as shown in the illustration.
- HINT:
- Align the fuel sub tank side mark with the hose side mark when installing the hose.
-
Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.
| 2.
INSTALL NO. 3 FUEL HOSE |
 |
- Install the fuel hose to the fuel sub tank as shown in the illustration.
- HINT:
- Align the fuel sub tank side mark with the hose side mark when installing the hose.
-
Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.
| 3.
INSTALL FUEL TANK BREATHER HOSE |
 |
- Install the breather hose to the fuel sub tank.
| 4.
INSTALL FUEL AND EVAPORATION VENT TUBE SUB-ASSEMBLY |
 |
- Install a new gasket to the fuel and evaporation vent tube.
Install the fuel and evaporation vent tube with the 6 bolts.
-
Torque:
- 3.5 N*m{
36 kgf*cm
, 31 in.*lbf
}
| 5.
INSTALL FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY |
 |
- Install the 2 fuel tank evaporation vent tubes.
| 6.
INSTALL FUEL HOSE |
 |
| 7.
INSTALL FUEL SENDER GAUGE ASSEMBLY |
 |
- Install a new gasket to the sender gauge.
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge.
Install the sender gauge with the 5 screws.
-
Torque:
- 1.5 N*m{
15 kgf*cm
, 13 in.*lbf
}
| 8.
INSTALL FLOOR NO. 3 WIRE |
 |
- Attach the wire harness clamp to the fuel sub tank.
Connect the sender gauge connector.
| 9.
INSTALL FUEL SUB TANK SUB-ASSEMBLY |
 |
Set the fuel sub tank on a transmission jack and raise the fuel sub tank.
- Connect the 2 fuel tank bands with the 2 bolts.
-
Torque:
- 40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
- Connect the floor No. 3 wire connector.
Attach the 3 wire harness clamps.
| 10.
CONNECT FUEL TANK TO FILLER PIPE HOSE |
 |
- Connect the hose to the filler pipe.
| 11.
CONNECT NO. 3 FUEL HOSE |
 |
- Connect the fuel hose to the filler pipe.
| 12.
CONNECT FUEL TANK BREATHER HOSE |
 |
- Connect the breather hose to the filler pipe.
| 13.
CONNECT FUEL HOSE |
 |
| 14.
CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY |
 |
- Connect the 2 fuel tank evaporation vent tubes.
| 15.
INSTALL FUEL TANK CAP ASSEMBLY |
|
| 16.
INSTALL NO. 1 SPARE WHEEL STOPPER |
 |
- Install the spare wheel stopper with the 2 bolts.
-
Torque:
- 32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
| 17.
INSTALL SPARE WHEEL CARRIER CROSSMEMBER AND SPARE WHEEL CARRIER BRACKET |
 |
Install the spare wheel carrier crossmember and 2 brackets to the vehicle with the 6 bolts labeled C.
-
Torque:
- for bolt C:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}


Temporarily install the bolt labeled A, and then tighten the bolt labeled A and bolts labeled B.
-
Torque:
- for bolt A:
- 29 N*m{
296 kgf*cm
, 21 ft.*lbf
}
- for bolt B:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
| 18.
INSTALL TAILPIPE ASSEMBLY
|
 |
Install the tailpipe to the 2 exhaust pipe supports.
Set a new gasket to the center exhaust pipe.
- Connect the tailpipe to the center pipe with a new clamp.
-
Torque:
- 32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
- HINT:
- Install the clamp within the angle range shown in the illustration.
| 19.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 20.
INSPECT FOR FUEL LEAK
|
 |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and intelligent tester on.
- NOTICE:
- Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
| 21.
INSPECT FOR EXHAUST GAS LEAK
|
 |
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.