REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Disconnect the cables from the negative (-) main battery and sub-battery terminals.
| 3.
REMOVE TAILPIPE ASSEMBLY
|
 |
Remove the bolt, clamp and gasket.
Disconnect the tailpipe from the 2 exhaust pipe supports.
| 4.
REMOVE SPARE WHEEL CARRIER CROSSMEMBER AND SPARE WHEEL CARRIER BRACKET |
 |
Remove the bolt labeled A, and then loosen the 4 bolts labeled B.


Slightly raise the spare wheel carrier crossmember, and then remove the 6 bolts labeled C, spare wheel carrier crossmember and 2 brackets.
| 5.
REMOVE NO. 1 SPARE WHEEL STOPPER |
 |
- Remove the 2 bolts and spare wheel stopper.
| 6.
REMOVE FUEL TANK CAP ASSEMBLY |
|
| 7.
DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY |
 |
- Disconnect the 2 fuel tank evaporation vent tubes.
| 8.
DISCONNECT FUEL HOSE |
 |
- Disconnect the 3 fuel hoses.
| 9.
DISCONNECT FUEL TANK BREATHER HOSE |
 |
- Disconnect the breather hose from the filler pipe.
| 10.
DISCONNECT NO. 3 FUEL HOSE |
 |
- Disconnect the fuel hose from the filler pipe.
| 11.
DISCONNECT FUEL TANK TO FILLER PIPE HOSE |
 |
- Disconnect the hose from the filler pipe.
| 12.
REMOVE FUEL SUB TANK SUB-ASSEMBLY |
 |
Disconnect the floor No. 3 wire connector.
Using a clip remover, detach the 3 wire harness clamps.
Place a transmission jack under the fuel sub tank.
- Remove the 2 bolts and disconnect the 2 fuel tank bands.
Lower the transmission jack to remove the fuel sub tank from the vehicle.
- NOTICE:
- Do not allow the fuel sub tank to contact the vehicle, especially the differential.
- HINT:
- Lower the transmission jack slowly.
| 13.
REMOVE FLOOR NO. 3 WIRE |
 |
- Disconnect the sender gauge connector.
Using a clip remover, detach the wire harness clamp.
| 14.
REMOVE FUEL SENDER GAUGE ASSEMBLY |
 |
- Remove the 5 screws and sender gauge.
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge.
Remove the gasket from the sender gauge.
| 15.
REMOVE FUEL HOSE |
 |
- Remove the 3 fuel hoses.
| 16.
REMOVE FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY |
 |
- Remove the 2 fuel tank evaporation vent tubes.
| 17.
REMOVE FUEL AND EVAPORATION VENT TUBE SUB-ASSEMBLY |
 |
- Remove the 6 bolts and fuel and evaporation vent tube.
Remove the gasket from the fuel and evaporation vent tube.
| 18.
REMOVE FUEL TANK BREATHER HOSE |
 |
- Remove the breather hose from the fuel sub tank.
| 19.
REMOVE NO. 3 FUEL HOSE |
 |
- Remove the fuel hose from the fuel sub tank.
| 20.
REMOVE FUEL TANK TO FILLER PIPE HOSE |
 |
- Remove the hose from the fuel sub tank.