2011-2013 Land Cruiser · Service Manual Power Source / Network

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR

  1. NO. 1 JUNCTION CONNECTOR
    C225721E01

    Text in Illustration 
    *1
    to Center Airbag Sensor (w/ Airbag System)
    *2
    to ECM
    *3
    to No. 2 Junction Connector
    *4
    to 4WD Control ECU (w/o Network Gateway ECU)
    No. 1 Junction Connector
    Wiring Color
    Connect to
    E72-1 (CANH)
    Y
    No. 2 junction connector
    E72-12 (CANL)
    B
    E72-2 (CANH)
    P
    ECM
    E72-13 (CANL)
    B
    E72-4 (CANH)*1
    GR
    Center airbag sensor*1
    E72-15 (CANL)*1
    B
    E72-5 (CANH)*2
    P
    4WD control ECU*2
    E72-16 (CANL)*2
    L
    1. *1: w/ Airbag System
    2. *2: w/o Network Gateway ECU

  2. NO. 2 JUNCTION CONNECTOR
    C172982E85

    Text in Illustration 
    *1
    to Air Conditioning Amplifier
    *2
    1. to No. 3 Junction Connector (w/ Network Gateway ECU)
    2. to No. 6 Junction Connector (w/o Network Gateway ECU)
    *3
    to Network Gateway ECU: V Bus (w/ Network Gateway ECU)
    *4
    to Display and Navigation Module Display (w/ Navigation System)
    *5
    to No. 1 Junction Connector
    -
    -
    No. 2 Junction Connector
    Wiring Color
    Connect to
    E69-1 (CANH)
    Y
    No. 1 junction connector
    E69-12 (CANL)
    B
    E69-2 (CANH)*1
    P
    Display and navigation module display*1
    E69-13 (CANL)*1
    B
    E69-3 (CANH)*2
    BR
    Network gateway ECU (V bus)*2
    E69-14 (CANL)*2
    B
    E69-4 (CANH)
    W*2
    Y*3
    1. No. 3 junction connector*2
    2. No. 6 junction connector*3
    E69-15 (CANL)
    B*2
    L*3
    E69-5 (CANH)
    G
    Air conditioning amplifier
    E69-16 (CANL)
    B
    1. *1: w/ Navigation System
    2. *2: w/ Network Gateway ECU
    3. *3: w/o Network Gateway ECU

  3. NO. 3 JUNCTION CONNECTOR
    C225721E02

    Text in Illustration 
    *1
    to Main Body ECU (Cowl Side Junction Block LH): V Bus
    *2
    to Combination Meter: V Bus
    *3
    to DLC3
    *4
    1. to No. 2 Junction Connector (w/ Network Gateway ECU)
    2. to No. 6 Junction Connector (w/o Network Gateway ECU)
    *5
    to Master Cylinder Solenoid (Skid Control ECU)
    (w/o Network Gateway ECU)
    -
    -
    No. 3 Junction Connector
    Wiring Color
    Connect to
    E75-1 (CANH)
    W*1
    Y*2
    1. No. 2 junction connector*1
    2. No. 6 junction connector*2
    E75-12 (CANL)
    B*1
    L*2
    E75-2 (CANH)
    G
    DLC3
    E75-13 (CANL)
    B
    E75-3 (CANH)
    V
    Combination meter (V bus)
    E75-14 (CANL)
    B
    E75-4 (CANH)
    SB
    Main body ECU (cowl side junction block LH) (V bus)
    E75-15 (CANL)
    B
    E75-5 (CANH)*2
    V
    Master cylinder solenoid (skid control ECU)*2
    E75-16 (CANL)*2
    L
    1. *1: w/ Network Gateway ECU
    2. *2: w/o Network Gateway ECU

  4. NO. 4 JUNCTION CONNECTOR (w/ Network Gateway ECU)
    C172982E88

    Text in Illustration 
    *1
    to 4WD Control ECU
    *2
    to Network Gateway ECU: Movement Control Bus
    *3
    to No. 5 Junction Connector
    -
    -
    No. 4 Junction Connector
    Wiring Color
    Connect to
    E71-1 (CANH)
    W
    No. 5 junction connector
    E71-12 (CANL)
    L
    E71-2 (CANH)
    SB
    Network gateway ECU (Movement control bus)
    E71-13 (CANL)
    L
    E71-3 (CANH)
    P
    4WD control ECU
    E71-14 (CANL)
    L

  5. NO. 5 JUNCTION CONNECTOR (w/ Network Gateway ECU)
    C172982E89

    Text in Illustration 
    *1
    to Seat Belt Control ECU (w/ Pre-crash Safety System)
    *2
    to Yaw Rate Sensor (w/ Vehicle Stability Control System)
    *3
    to No. 6 Junction Connector
    *4
    to No. 4 Junction Connector
    No. 5 Junction Connector
    Wiring Color
    Connect to
    E68-1 (CANH)
    W
    No. 4 junction connector
    E68-12 (CANL)
    L
    E68-2 (CANH)
    Y
    No. 6 junction connector
    E68-13 (CANL)
    L
    E68-3 (CANH)*1
    BR
    Yaw rate sensor*1
    E68-14 (CANL)*1
    L
    E68-5 (CANH)*2
    G
    Seat belt control ECU*2
    E68-16 (CANL)*2
    L
    1. *1: w/ Vehicle Stability Control System
    2. *2: w/ Pre-crash Safety System

  6. NO. 6 JUNCTION CONNECTOR (except Double Swing Out Type)
    C172982E90

    Text in Illustration 
    *1
    1. to No. 5 Junction Connector (w/ Network Gateway ECU)
    2. to No. 2 Junction Connector (w/o Network Gateway ECU)
    *2
    1. to No. 7 Junction Connector (w/ Network Gateway ECU)
    2. to No. 3 Junction Connector (w/o Network Gateway ECU)
    *3
    1. to Clearance Warning ECU (w/ TOYOTA Parking Assist-sensor System)
    2. to Parking Assist ECU (w/ Parking Monitor System)
    -
    -
    No. 6 Junction Connector
    Wiring Color
    Connect to
    F21-1 (CANH)
    V
    1. Clearance warning ECU*1
    2. Parking assist ECU*2
    F21-12 (CANL)
    L
    F21-2 (CANH)
    Y
    1. No. 7 junction connector*3
    2. No. 3 junction connector*4
    F21-13 (CANL)
    L
    F21-3 (CANH)
    Y
    1. No. 5 junction connector*3
    2. No. 2 junction connector*4
    F21-14 (CANL)
    L
    1. *1: w/ TOYOTA Parking Assist-sensor System
    2. *2: w/ Parking Assist Monitor System
    3. *3: w/ Network Gateway ECU
    4. *4: w/o Network Gateway ECU

  7. NO. 6 JUNCTION CONNECTOR (for Double Swing Out Type)
    C246722E01

    Text in Illustration 
    *1
    1. to No. 7 Junction Connector (w/ Network Gateway ECU)
    2. to No. 3 Junction Connector (w/o Network Gateway ECU)
    *2
    1. to No. 5 Junction Connector (w/ Network Gateway ECU)
    2. to No. 2 Junction Connector (w/o Network Gateway ECU)
    No. 6 Junction Connector
    Wiring Color
    Connect to
    F73-6 (CANH)
    Y
    1. No. 7 junction connector*1
    2. No. 3 junction connector*2
    F73-17 (CANL)
    L
    F73-7 (CANH)
    Y
    1. No. 5 junction connector*1
    2. No. 2 junction connector*2
    F73-18 (CANL)
    L
    1. *1: w/ Network Gateway ECU
    2. *2: w/o Network Gateway ECU

  8. NO. 7 JUNCTION CONNECTOR (w/ Network Gateway ECU)
    E194837E02

    Text in Illustration 
    *1
    to Master Cylinder Solenoid (Skid Control ECU)
    *2
    to Steering Angle Sensor (w/ Vehicle Stability Control System or Parking Assist Monitor System)
    *3
    to Steering Control ECU (w/ Variable Gear Ratio Steering System)
    *4
    to No. 6 Junction Connector
    *5
    to No. 1 CAN Junction Connector
    -
    -
    No. 7 Junction Connector
    Wiring Color
    Connect to
    E74-1 (CANH)
    W
    No. 1 CAN junction connector
    E74-12 (CANL)
    L
    E74-2 (CANH)
    Y
    No. 6 junction connector
    E74-13 (CANL)
    L
    E74-3 (CANH)*1
    LG
    Steering control ECU*1
    E74-14 (CANL)*1
    L
    E74-4 (CANH)*2
    GR
    Steering angle sensor*2
    E74-15 (CANL)*2
    L
    E74-5 (CANH)
    V
    Master cylinder solenoid (skid control ECU)
    E74-16 (CANL)
    L
    1. *1: w/ Variable Gear Ratio Steering System
    2. *2: w/ Vehicle Stability Control System or Parking Assist Monitor System

  9. NO. 8 JUNCTION CONNECTOR
    E194837E03

    Text in Illustration 
    *1
    to Main Body ECU (Cowl Side Junction Block LH): MS Bus
    *2
    to Outer Mirror Control ECU (w/ Seat Memory)
    *3
    to Position Control ECU and Switch (w/ Seat Memory)
    *4
    to Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System)
    *5
    to Certification ECU (Smart Key ECU Assembly)
    *6
    to No. 2 CAN Junction Connector
    No. 8 Junction Connector
    Wiring Color
    Connect to
    E76-1 (CANH)
    W
    No. 2 CAN junction connector
    E76-12 (CANL)
    R
    E76-2 (CANH)
    LG
    Certification ECU (smart key ECU assembly)
    E76-13 (CANL)
    R
    E76-3 (CANH)*2
    P
    Multiplex tilt and telescopic ECU*2
    E76-14 (CANL)*2
    R
    E76-4 (CANH)*1
    V
    Position control ECU and switch*1
    E76-15 (CANL)*1
    R
    E76-5 (CANH)*1
    BR
    Outer mirror control ECU*1
    E76-16 (CANL)*1
    R
    E76-6 (CANH)
    GR
    Main body ECU (cowl side junction block LH) (MS bus)
    E76-17 (CANL)
    R
    1. *1: w/ Seat Memory
    2. *2: w/ Power Tilt and Power Telescopic Steering Column System

  10. NO. 9 JUNCTION CONNECTOR
    E194837E19

    Text in Illustration 
    *1
    to Windshield Wiper ECU (w/ Rain Sensor)
    *2
    to No. 2 CAN Junction Connector
    *3
    to No. 10 Junction Connector
    *4
    to Accessory Bus Buffer
    No. 9 Junction Connector
    Wiring Color
    Connect to
    E73-1 (CANH)
    W
    No. 10 junction connector
    E73-12 (CANL)
    R
    E73-2 (CANH)
    Y
    No. 2 CAN junction connector
    E73-13 (CANL)
    R
    E73-3 (CANH)
    V
    Accessory bus buffer
    E73-14 (CANL)
    R
    E73-4 (CANH)*
    LG
    Windshield wiper ECU*
    E73-15 (CANL)*
    R
    1. *: w/ Rain Sensor

  11. NO. 10 JUNCTION CONNECTOR
    E194837E05

    Text in Illustration 
    *1
    to Combination Meter: MS Bus
    *2
    to No. 9 Junction Connector
    No. 10 Junction Connector
    Wiring Color
    Connect to
    E70-1 (CANH)
    W
    No. 9 junction connector
    E70-12 (CANL)
    R
    E70-3 (CANH)
    LG
    Combination meter (MS bus)
    E70-14 (CANL)
    R

  12. NO. 1 CAN JUNCTION CONNECTOR (w/ Network Gateway ECU)
    E211948E01

    Junction Connector A Side
    Wiring Color (CANH Side)
    Wiring Color (CANL Side)
    Ground terminal (K28)
    -
    W-B
    No. 7 junction connector (K29)
    W
    L
    Suspension control ECU (K39)*
    V
    L
    1. *: w/ Active Height Control Suspension

  13. NO. 2 CAN JUNCTION CONNECTOR
    E211949E01

    Junction Connector B Side
    Wiring Color (CANH Side)
    Wiring Color (CANL Side)
    No. 8 junction connector (L29)
    W
    R
    No. 9 junction connector (L30)
    Y
    R


TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (CAN JUNCTION CONNECTOR)
C135249
Terminal No.
Symbol
1
CANH
2
CANL

CHECK DLC3
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. H102621E08
    Measure the resistance according to the value(s) in the table below.
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    G - B
    Ignition switch off
    54 to 69 Ω
    E22-6 (CANH) - E22-4 (CG)
    G - W-B
    Ignition switch off
    200 Ω or higher
    E22-14 (CANL) - E22-4 (CG)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E22-6 (CANH) - E22-16 (BAT)
    G - BE
    Ignition switch off
    6 kΩ or higher
    E22-14 (CANL) - E22-16 (BAT)
    B - BE
    Ignition switch off
    6 kΩ or higher


CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)
C172598E01
  1. Disconnect the A24 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A24-11 (CANH) - A24-25 (CANL)
    V - L
    Ignition switch off
    54 to 69 Ω
    A24-11 (CANH) - A24-1 (GND1)
    V - W-B
    Ignition switch off
    200 Ω or higher
    A24-25 (CANL) - A24-1 (GND1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    A24-11 (CANH) - A24-2 (+BM1)
    V - B
    Ignition switch off
    6 kΩ or higher
    A24-25 (CANL) - A24-2 (+BM1)
    L - B
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER (w/ REAR AIR CONDITIONING AMPLIFIER)
C148519E06
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E35-3 (CANH) - E35-4 (CANL)
    G - B
    Ignition switch off
    54 to 69 Ω
    E35-3 (CANH) - E36-1 (GND)
    G - W-B
    Ignition switch off
    200 Ω or higher
    E35-4 (CANL) - E36-1 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E35-3 (CANH) - E36-6 (+B1)
    G - R
    Ignition switch off
    6 kΩ or higher
    E35-4 (CANL) - E36-6 (+B1)
    B - R
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER (w/o REAR CONDITIONING AMPLIFIER)
C159478E02
  1. Disconnect the E81 amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E81-11 (CANH) - E81-12 (CANL)
    G - B
    Ignition switch off
    54 to 69 Ω
    E81-11 (CANH) - E81-14 (GND)
    G - W-B
    Ignition switch off
    200 Ω or higher
    E81-12 (CANL) - E81-14 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E81-11 (CANH) - E81-21 (+B1)
    G - R
    Ignition switch off
    6 kΩ or higher
    E81-12 (CANL) - E81-21 (+B1)
    B - R
    Ignition switch off
    6 kΩ or higher


CHECK ECM
C159489E24
Text in Illustration 
*A
for 2UZ-FE
*B
for 1GR-FE
*C
for 1VD-FTV
*D
for 3UR-FE
  1. Disconnect the A38 and C45 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A38-10 (CANH) - A38-11 (CANL)*1
    P - B
    Ignition switch off
    108 to 132 Ω
    A38-10 (CANH) - C45-81 (E1)*1
    P - BR
    Ignition switch off
    200 Ω or higher
    A38-11 (CANL) - C45-81 (E1)*1
    B - BR
    Ignition switch off
    200 Ω or higher
    A38-10 (CANH) - A38-1 (BATT)*1
    P - L
    Ignition switch off
    6 kΩ or higher
    A38-11 (CANL) - A38-1 (BATT)*1
    B - L
    Ignition switch off
    6 kΩ or higher
    A38-41 (CANH) - A38-49 (CANL)*2
    P - B
    Ignition switch off
    108 to 132 Ω
    A38-41 (CANH) - C45-81 (E1)*2
    P - BR
    Ignition switch off
    200 Ω or higher
    A38-49 (CANL) - C45-81 (E1)*2
    B - BR
    Ignition switch off
    200 Ω or higher
    A38-41 (CANH) - A38-20 (BATT)*2
    P - L
    Ignition switch off
    6 kΩ or higher
    A38-49 (CANL) - A38-20 (BATT)*2
    B - L
    Ignition switch off
    6 kΩ or higher
    A38-41 (CANH) - A38-49 (CANL)*3
    P - B
    Ignition switch off
    108 to 132 Ω
    A38-41 (CANH) - C45-81 (E1)*3
    P - BR
    Ignition switch off
    200 Ω or higher
    A38-49 (CANL) - C45-81 (E1)*3
    B - BR
    Ignition switch off
    200 Ω or higher
    A38-41 (CANH) - A38-20 (BATT)*3
    P - L
    Ignition switch off
    6 kΩ or higher
    A38-49 (CANL) - A38-20 (BATT)*3
    B - L
    Ignition switch off
    6 kΩ or higher
    A38-10 (CANH) - A38-11 (CANL)*4
    P - B
    Ignition switch off
    108 to 132 Ω
    A38-10 (CANH) - C45-81 (E1)*4
    P - W-B
    Ignition switch off
    200 Ω or higher
    A38-11 (CANL) - C45-81 (E1)*4
    B - W-B
    Ignition switch off
    200 Ω or higher
    A38-10 (CANH) - A38-1 (BATT)*4
    P - L
    Ignition switch off
    6 kΩ or higher
    A38-11 (CANL) - A38-1 (BATT)*4
    B - L
    Ignition switch off
    6 kΩ or higher
    1. *1: for 2UZ-FE
    2. *2: for 1GR-FE
    3. *3: for 1VD-FTV
    4. *4: for 3UR-FE


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E01
  1. Disconnect the E3 ECU connector.

  2. Disconnect the 2A and 2D junction connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E3-5 (CANH) - E3-6 (CANL)*1
    SB - B
    Ignition switch off
    54 to 69 Ω
    E3-5 (CANH) - 2D-62 (GND2)*1
    SB - W-B
    Ignition switch off
    200 Ω or higher
    E3-6 (CANL) - 2D-62 (GND2)*1
    B - W-B
    Ignition switch off
    200 Ω or higher
    E3-5 (CANH) - 2A-1 (ALTB)*1
    SB - B
    Ignition switch off
    6 kΩ or higher
    E3-6 (CANL) - 2A-1 (ALTB)*1
    B - B
    Ignition switch off
    6 kΩ or higher
    E3-16 (CANP) - E3-15 (CANN)*2
    GR - R
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - 2D-62 (GND2)*2
    GR - W-B
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - 2D-62 (GND2)*2
    R - W-B
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - 2A-1 (ALTB)*2
    GR - B
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - 2A-1 (ALTB)*2
    R - B
    Ignition switch off
    6 kΩ or higher
    1. *1: for V bus
    2. *2: for MS bus


CHECK COMBINATION METER
E154040E02
  1. Disconnect the E7 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E7-25 (CANH) - E7-26 (CANL)*1
    V - B
    Ignition switch off
    108 to 132 Ω
    E7-25 (CANH) - E7-14 (EP)*1
    V - W-B
    Ignition switch off
    200 Ω or higher
    E7-26 (CANL) - E7-14 (EP)*1
    B - W-B
    Ignition switch off
    200 Ω or higher
    E7-25 (CANH) - E7-17 (B)*1
    V - R
    Ignition switch off
    6 kΩ or higher
    E7-26 (CANL) - E7-17 (B)*1
    B - R
    Ignition switch off
    6 kΩ or higher
    E7-1 (MPX+) - E7-2 (MPX-)*2
    LG - R
    Ignition switch off
    108 to 132 Ω
    E7-1 (MPX+) - E7-14 (EP)*2
    LG - W-B
    Ignition switch off
    200 Ω or higher
    E7-2 (MPX-) - E7-14 (EP)*2
    R - W-B
    Ignition switch off
    200 Ω or higher
    E7-1 (MPX+) - E7-17 (B)*2
    LG - R
    Ignition switch off
    6 kΩ or higher
    E7-2 (MPX-) - E7-17 (B)*2
    R - R
    Ignition switch off
    6 kΩ or higher
    1. *1: for V bus
    2. *2: for MS bus


CHECK CENTER AIRBAG SENSOR (w/ Airbag System)
C149302E02
  1. Disconnect the E47 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E47-13 (CANH) - E47-22 (CANL)
    GR - B
    Ignition switch off
    54 to 69 Ω
    E47-13 (CANH) - E47-25 (E1)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    E47-22 (CANL) - E47-25 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E47-13 (CANH) - E22-16 (BAT)
    GR - BE
    Ignition switch off
    6 kΩ or higher
    E47-22 (CANL) - E22-16 (BAT)
    B - BE
    Ignition switch off
    6 kΩ or higher


CHECK DISPLAY AND NAVIGATION MODULE DISPLAY

HINT:
For vehicles with the navigation system only.

E189961E06
  1. Disconnect the F64 display connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F64-21 (CANH) - F64-22 (CANL)
    P - B
    Ignition switch off
    54 to 69 Ω
    F64-21 (CANH) - F64-10 (GND1)
    P - W-B
    Ignition switch off
    200 Ω or higher
    F64-22 (CANL) - F64-10 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    F64-21 (CANH) - F64-1 (+B1)
    P - R
    Ignition switch off
    6 kΩ or higher
    F64-22 (CANL) - F64-1 (+B1)
    B - R
    Ignition switch off
    6 kΩ or higher


CHECK STEERING ANGLE SENSOR

HINT:
Vehicle with the vehicle stability control system or the parking assist monitor system only.

C164885E03
  1. Disconnect the E11 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E11-10 (CANH) - E11-9 (CANL)
    GR - L
    Ignition switch off
    54 to 69 Ω
    E11-10 (CANH) - E11-2 (ESS)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    E11-9 (CANL) - E11-2 (ESS)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E11-10 (CANH) - E22-16 (BAT)
    GR - BE
    Ignition switch off
    6 kΩ or higher
    E11-9 (CANL) - E22-16 (BAT)
    L - BE
    Ignition switch off
    6 kΩ or higher


CHECK YAW RATE SENSOR

HINT:
Vehicle with the vehicle stability control system only.

C149304E02
  1. Disconnect the E50 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E50-3 (CANH) - E50-2 (CANL)
    BR - L
    Ignition switch off
    54 to 69 Ω
    E50-3 (CANH) - E50-1 (GND)
    BR - W-B
    Ignition switch off
    200 Ω or higher
    E50-2 (CANL) - E50-1 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E50-3 (CANH) - E22-16 (BAT)
    BR - BE
    Ignition switch off
    6 kΩ or higher
    E50-2 (CANL) - E22-16 (BAT)
    L - BE
    Ignition switch off
    6 kΩ or higher


CHECK SEAT BELT CONTROL ECU

HINT:
For vehicles with the pre-crash safety system only.

C148536E03
  1. Disconnect the E41 and E42 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E42-1 (CANH) - E42-2 (CANL)
    G - L
    Ignition switch off
    54 to 69 Ω
    E42-1 (CANH) - E41-8 (PGND)
    G - W-B
    Ignition switch off
    200 Ω or higher
    E42-2 (CANL) - E41-8 (PGND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E42-1 (CANH) - E41-7 (+B)
    G - R
    Ignition switch off
    6 kΩ or higher
    E42-2 (CANL) - E41-7 (+B)
    L - R
    Ignition switch off
    6 kΩ or higher


CHECK CLEARANCE WARNING ECU

HINT:
For vehicles with the TOYOTA parking assist-sensor system only.

C149307E02
  1. Disconnect the F12 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F12-3 (CANH) - F12-5 (CANL)
    V - L
    Ignition switch off
    54 to 69 Ω
    F12-3 (CANH) - F12-17 (GND1)
    V - W-B
    Ignition switch off
    200 Ω or higher
    F12-5 (CANL) - F12-17 (GND1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    F12-3 (CANH) - E22-16 (BAT)
    V - BE
    Ignition switch off
    6 kΩ or higher
    F12-5 (CANL) - E22-16 (BAT)
    L - BE
    Ignition switch off
    6 kΩ or higher


CHECK OUTER MIRROR CONTROL ECU

HINT:
For vehicles with the seat memory only.

B166573E04
  1. Disconnect the I17 and I18 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    I18-1 (CANH) - I18-21 (CANL)
    BR - R
    Ignition switch off
    54 to 69 Ω
    I18-1 (CANH) - I17-9 (GND)
    BR - W-B
    Ignition switch off
    200 Ω or higher
    I18-21 (CANL) - I17-9 (GND)
    R - W-B
    Ignition switch off
    200 Ω or higher
    I18-1 (CANH) - I17-3 (B)
    BR - R
    Ignition switch off
    6 kΩ or higher
    I18-21 (CANL) - I17-3 (B)
    R - R
    Ignition switch off
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU

HINT:
For vehicles with the power tilt and power telescopic steering column system only.

C149308E03
  1. Disconnect the E27 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E27-5 (CANP) - E27-14 (CANN)
    P - R
    Ignition switch off
    54 to 69 Ω
    E27-5 (CANP) - E27-11 (GND)
    P - W-B
    Ignition switch off
    200 Ω or higher
    E27-14 (CANN) - E27-11 (GND)
    R - W-B
    Ignition switch off
    200 Ω or higher
    E27-5 (CANP) - E27-2 (+B)
    P - L
    Ignition switch off
    6 kΩ or higher
    E27-14 (CANN) - E27-2 (+B)
    R - L
    Ignition switch off
    6 kΩ or higher


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
C149309E04
  1. Disconnect the E29 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E29-27 (CANH) - E29-28 (CANL)
    LG - R
    Ignition switch off
    54 to 69 Ω
    E29-27 (CANH) - E29-17 (E)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    E29-28 (CANL) - E29-17 (E)
    R - W-B
    Ignition switch off
    200 Ω or higher
    E29-27 (CANH) - E29-1 (+B)
    LG - B
    Ignition switch off
    6 kΩ or higher
    E29-28 (CANL) - E29-1 (+B)
    R - B
    Ignition switch off
    6 kΩ or higher


CHECK POSITION CONTROL ECU AND SWITCH

HINT:
For vehicles with the seat memory only.

C159480E02
  1. Disconnect the c14 and c15 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    c15-5 (MPX1) - c15-1 (MPX2)
    V - R
    Ignition switch off
    54 to 69 Ω
    c15-5 (MPX1) - c14-1 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    c15-1 (MPX2) - c14-1 (GND)
    R - W-B
    Ignition switch off
    200 Ω or higher
    c15-5 (MPX1) - c14-5 (+B)
    V - L
    Ignition switch off
    6 kΩ or higher
    c15-1 (MPX2) - c14-5 (+B)
    R - L
    Ignition switch off
    6 kΩ or higher


CHECK 4WD CONTROL ECU
C159479E03
  1. Disconnect the A27 and A28 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A27-19 (CAN+) - A27-20 (CAN-)
    P - L
    Ignition switch off
    54 to 69 Ω
    A27-19 (CAN+) - A28-4 (GND)
    P - W
    Ignition switch off
    200 Ω or higher
    A27-20 (CAN-) - A28-4 (GND)
    L - W
    Ignition switch off
    200 Ω or higher
    A27-19 (CAN+) - E22-16 (BAT)
    P - BE
    Ignition switch off
    6 kΩ or higher
    A27-20 (CAN-) - E22-16 (BAT)
    L - BE
    Ignition switch off
    6 kΩ or higher


CHECK NETWORK GATEWAY ECU

HINT:
For vehicles with the network gateway ECU only.

C172506E01
  1. Disconnect the E31 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E31-16 (CA1H) - E31-15 (CA1L)*1
    BR - B
    Ignition switch off
    54 to 69 Ω
    E31-16 (CA1H) - E31-4 (GND)*1
    BR - W-B
    Ignition switch off
    200 Ω or higher
    E31-15 (CA1L) - E31-4 (GND)*1
    B - W-B
    Ignition switch off
    200 Ω or higher
    E31-16 (CA1H) - E31-2 (BATT)*1
    BR - R
    Ignition switch off
    6 kΩ or higher
    E31-15 (CA1L) - E31-2 (BATT)*1
    B - R
    Ignition switch off
    6 kΩ or higher
    E31-13 (CA2H) - E31-12 (CA2L)*2
    SB - L
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E31-4 (GND)*2
    SB - W-B
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E31-4 (GND)*2
    L - W-B
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E31-2 (BATT)*2
    SB - R
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E31-2 (BATT)*2
    L - R
    Ignition switch off
    6 kΩ or higher
    1. *1: for V bus
    2. *2: for Movement control bus


CHECK STEERING CONTROL ECU

HINT:
For vehicles with the variable gear ratio steering system only.

C107444E06
  1. Disconnect the E77 and E79 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E79-9 (CANH) - E79-20 (CANL)
    LG - L
    Ignition switch off
    54 to 69 Ω
    E79-9 (CANH) - E77-7 (PGND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    E79-20 (CANL) - E77-7 (PGND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E79-9 (CANH) - E77-10 (+B1)
    LG - R
    Ignition switch off
    6 kΩ or higher
    E79-20 (CANL) - E77-10 (+B1)
    L - R
    Ignition switch off
    6 kΩ or higher


CHECK SUSPENSION CONTROL ECU

HINT:
For vehicles with the active height control suspension only.

C150345E04
  1. Disconnect the K34 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    K34-7 (CANH) - K34-8 (CANL)
    V - L
    Ignition switch off
    54 to 69 Ω
    K34-7 (CANH) - K34-1 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    K34-8 (CANL) - K34-1 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    K34-7 (CANH) - K34-3 (BAT2)
    V - R
    Ignition switch off
    6 kΩ or higher
    K34-8 (CANL) - K34-3 (BAT2)
    L - R
    Ignition switch off
    6 kΩ or higher


CHECK WINDSHIELD WIPER ECU

HINT:
For vehicles with the rain sensor only.

C177370E01
  1. Disconnect the E85 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E85-6 (CANH) - E85-5 (CANL)
    LG - R
    Ignition switch off
    54 to 69 Ω
    E85-6 (CANH) - E85-10 (E)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    E85-5 (CANL) - E85-10 (E)
    R - W-B
    Ignition switch off
    200 Ω or higher
    E85-6 (CANH) - E22-16 (BAT)
    LG - BE
    Ignition switch off
    6 kΩ or higher
    E85-5 (CANL) - E22-16 (BAT)
    R - BE
    Ignition switch off
    6 kΩ or higher


CHECK PARKING ASSIST ECU

HINT:
For vehicles with the parking assist monitor system only.

E132051E07
  1. Disconnect the F43 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    F43-9 (CANH) - F43-10 (CANL)
    V - L
    Ignition switch off
    54 to 69 Ω
    F43-9 (CANH) - F43-4 (GND1)
    V - W-B
    Ignition switch off
    200 Ω or higher
    F43-10 (CANL) - F43-4 (GND1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    F43-9 (CANH) - F43-6 (+B)
    V - L
    Ignition switch off
    6 kΩ or higher
    F43-10 (CANL) - F43-6 (+B)
    L - L
    Ignition switch off
    6 kΩ or higher


CHECK ACCESSORY BUS BUFFER
E211925E01
  1. Disconnect the E6 buffer connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E6-1 (CAN+) - E6-2 (CAN-)
    V - R
    Ignition switch off
    54 to 69 Ω
    E6-1 (CAN+) - E22-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    E6-2 (CAN-) - E22-4 (CG)
    R - W-B
    Ignition switch off
    200 Ω or higher
    E6-1 (CAN+) - E22-16 (BAT)
    V - BE
    Ignition switch off
    6 kΩ or higher
    E6-2 (CAN-) - E22-16 (BAT)
    R - BE
    Ignition switch off
    6 kΩ or higher

← PROBLEM SYMPTOMS TABLE (from Jan 2012)TERMINALS OF ECU (from Jan 2012) →