FAIL-SAFE CHART
System information · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| FAIL-SAFE FUNCTION |
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
System
Function
Control Description
- Control Master
- System Related
- Control Actuator
Fail-safe Function System Behavior
Indicator and Buzzer Behavior or User Notification
Airbag (ABG)
TC DTC/output service
When TC is on, DTCs (warning light turn on/turn off request signals) are output.
- Center Airbag Sensor
- -
- Combination Meter
-
-
Event recorder (EDR)
Records the vehicle information during a collision (the vehicle speed, accelerator pedal opening angle, shift position, etc.).
- Center Airbag Sensor
- Combination Meter, ECM
- -
-
-
SRS warning light control
Turns the SRS warning light on/off.
- Combination Meter
- Center Airbag Sensor
- -
The SRS warning light turns on.
-
Information output function (Refer to related system for control description details)
The collision detection signal stops the fuel pump during a collision.
- ECM
- Center Airbag Sensor
- -
-
-
The driver/passenger seat buckle switch stops PSB control when the seat belt is not fastened.
- Seat Belt Control ECU
- Center Airbag Sensor
- -
-
-
The passenger seat occupant detection signal turns on the seat belt warning light when the seat belt is not fastened.
- Combination Meter
- Center Airbag Sensor
- -
-
-
Brake (VSC or ABS)
Warning light control
BRL, ABS, VSC-OFF, SLIP and CRAWL light control (turn on/off, blink, DTC output).
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
- -
- Combination Meter
-
-
ABS control
ABS control according to the G sensor signal.
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
- Yaw Rate Sensor
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
The ABS does not operate.
ABS and VSC warning light turns on.
TRC control
Brake control and engine torque control during acceleration slip.
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
- ECM, 4WD Control ECU
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
TRC does not operate.
VSC control
VSC control according to the yaw rate and steering angle sensor signal.
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
- ECM, 4WD Control ECU, Steering Angle Sensor, Yaw Rate Sensor, Steering Control ECU
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
VSC does not operate.
Tilt and Telescopic (TAT)
Microcomputer preset steering
Automatically begins the steering auto away/auto return when the ignition switch is turned ON or OFF.
- Multiplex Tilt and Telescopic ECU
- Position Control ECU and Switch, Main Body ECU (Cowl Side Junction Block LH) (V Bus), Combination Meter
- Multiplex Tilt and Telescopic ECU, Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
The power tilt and power telescopic steering column system does not operate.
-
Memory restore control does not operate.
-
Auto return/auto away control does not operate.
-
Mechanical 4WD (FWM)
Switching control between high and low
Switching between high and low is prohibited during the following conditions: 1) When there is a vehicle speed violation, engine speed violation, or large difference in wheel speeds, 2) when the shift lever is not in N, or 3) when the clutch is not on.
- 4WD Control ECU
- -
- -
-
-
- -
- ECM, Master Cylinder Solenoid (Skid Control ECU)
- -
Switching between high and low is prohibited. - HINT:
- When there is a wheel speed malfunction, function No. 7 is controlled to determine if switching between high and low can be performed.
DL indicator light blinks (at 0.2 sec. intervals) or 4LO indicator light blinks (at 0.2 sec. intervals) or DL and 4LO indicator lights blink (at 0.2 sec. intervals).
Neutral switching control
Switching to neutral is prohibited during the following conditions: 1) When there is a vehicle speed violation or engine speed violation, or 2) when the shift lever is not in N or the clutch is not on.
- 4WD Control ECU
- -
- -
-
-
- -
- ECM, Master Cylinder Solenoid (Skid Control ECU)
- -
Switching to neutral is prohibited.
4LO indicator light blinks (at 0.2 sec. intervals) or DL and 4LO indicator lights blink (at 0.2 sec. intervals).
Center differential lock switching control (between Free and Lock)
Center differential lock switching is prohibited when there is a vehicle speed violation or large difference in wheel speeds.
- 4WD Control ECU
- -
- -
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Center differential lock switching is prohibited. - HINT:
- When there is a wheel speed malfunction, function No. 7 is controlled to determine if center differential lock switching can be performed.
DL indicator light blinks (at 0.2 sec. intervals) or DL and 4LO indicator lights blink (at 0.2 sec. intervals).
Mechanical 4WD (FWM)
Rear differential lock switching control (between RrFree and RrLock)
Rear differential lock switching is prohibited when there is a vehicle speed violation.
- 4WD Control ECU
- -
- -
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Rear differential lock switching is prohibited. - HINT:
- When there is a wheel speed malfunction, function No. 7 is controlled to determine if rear differential lock switching can be performed.
DL indicator light blinks (at 0.2 sec. intervals) or DL and 4LO indicator lights blink (at 0.2 sec. intervals).
L4F switching control
Switching to L4F is prohibited and the operation is performed with L4L when VSC is malfunctioning.
- 4WD Control ECU
- -
- -
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
L4F switching is prohibited and the operation is performed with L4L.
No user notification.
Specialized control when temperature is low
Changes the ACT conductive current value according to the temperature (low temperature use or normal temperature use).
- 4WD Control ECU
- -
- -
-
-
- -
- Air Conditioning Amplifier, ECM
- -
Changes the temperature used for the calculation of ACT temperature adjustment control.
No user notification.
Mechanical 4WD (FWM)
Specialized control during wheel speed failure
When there is a wheel speed failure, switching is permitted only when specified conditions are met (the wheel speed malfunction is 1 wheel or more and 3 wheels or less, the brake is applied, the engine speed is low, and all normal wheel speeds are low).
- 4WD Control ECU
- -
- -
-
-
- -
- ECM, Master Cylinder Solenoid (Skid Control ECU)
- -
If the wheel speed malfunction is 1 wheel or more and 3 wheels or less, only when the wheel speed failure specified conditions are met, switching is permitted. When 4 wheels are malfunctioning, switching is prohibited (the wheel speed failure specialized control does not operate).
DL indicator light blinks (at 0.2 sec. intervals) or DL and 4LO indicator lights blink (at 0.2 sec. intervals).
Switching vehicle speed specialized control according to gear shift judgment when M/T vehicle is changed from low to high
Determines the gear for an M/T vehicle, and changes the possible low to high switching vehicle speed.
- 4WD Control ECU
- -
- -
-
-
- -
- ECM, Master Cylinder Solenoid (Skid Control ECU)
- -
Switching between high and low is prohibited. - HINT:
- When there is a wheel speed malfunction, function No. 7 is controlled to determine if switching between high and low can be performed.
DL indicator light blinks (at 0.2 sec. intervals) or 4LO indicator light blinks (at 0.2 sec. intervals) or DL and 4LO indicator lights blink (at 0.2 sec. intervals).
Mechanical 4WD (FWM)
Indicator and buzzer signal output
Signal output of the indicator and buzzer condition that indicates the actuator position and switching status.
- 4WD Control ECU
- -
- -
-
-
High-Low actuator failure signal output
When the High-Low actuator limit switch is malfunctioning, a signal is output.
- 4WD Control ECU
- -
- -
-
-
C/C cancel signal output
Outputs a cruise control cancel signal when center differential switching is not completed even though 5 sec. or more have elapsed from the start of switching.
- 4WD Control ECU
- -
- -
-
-
L4 status signal condition output
A signal is output when switching between the L4F and L4L position is completed.
- 4WD Control ECU
- -
- -
-
-
C/D lock condition signal output
CDL switch condition is output.
- 4WD Control ECU
- -
- -
-
-
R/D lock condition signal output
R switch condition is output.
- 4WD Control ECU
- -
- -
-
-
T/F N condition signal output
NP switch condition is output.
- 4WD Control ECU
- -
- -
-
-
Gasoline (Diesel) Engine
Engine control system
Adjusts the fuel injection volume according to each sensor value and controls the engine.
- ECM
- -
- -
-
-
ECT system
Changes the ECT shift position based on the vehicle speed and torque.
- ECM
- -
- -
-
-
Cruise control system
Maintains a constant vehicle speed and drives the vehicle.
- ECM
- -
- -
-
-
Active Height Control Suspension (4-WHEEL AHC)
Damping force control
Based on the information from the ECM, master cylinder solenoid (skid control ECU), steering control ECU, and steering angle sensor, detects the driving conditions, road surface conditions, etc. and changes the damping force of shock absorbers.
- Suspension Control ECU
- -
- Suspension Control ECU
-
-
- -
- ECM
- -
Damping force control is prohibited.
-
- -
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
- -
-
- -
- Steering Angle Sensor
- -
-
- -
- Steering Control ECU
- -
-
Spring switching control is prohibited
Based on the information from the master cylinder solenoid (skid control ECU), steering control ECU, yaw rate sensor and steering angle sensor, detects the driving conditions, road surface conditions, etc. and changes front spring constant value (ON/OFF).
- Suspension Control ECU
- -
- Suspension Control ECU
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Spring switching control is prohibited.
"Check 4-WHEEL AHC System" illuminates.
- -
- Steering Angle Sensor
- -
- -
- Steering Control ECU
- -
- -
- Yaw Rate Sensor
- -
Active Height Control Suspension (4-WHEEL AHC)
Vehicle height control
Based on the information from the ECM, master cylinder solenoid (skid control ECU), steering control ECU, 4WD, main body ECU (cowl side junction block LH), yaw rate sensor and steering angle sensor, detects the driving conditions, road surface conditions, etc. and restricts vehicle height changes.
- Suspension Control ECU
- -
- Suspension Control ECU
-
-
- Suspension Control ECU
- ECM
- Suspension Control ECU
Vehicle height control is prohibited.
-
- -
- ECM
- -
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
Vehicle height control is prohibited.
-
- -
- 4WD Control ECU
- -
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Vehicle height control is prohibited.
"Check 4-WHEEL AHC System" illuminates.
- -
- Steering Angle Sensor
- -
- -
- Steering Control ECU
- -
- -
- Yaw Rate Sensor
- -
Air Conditioner (ACN)
Air conditioning system
- Air conditioning vent temperature control according to the engine coolant temperature information.
- Air conditioning vent switching control according to the engine coolant temperature information.
- Air conditioning vent airflow amount control according to the engine coolant temperature information.
- Compensation of the engine coolant temperature information according to the engine type.
- Compressor lock judgment value switching according to the engine type.
- Air Conditioning Amplifier
- ECM
- -
Coolant information: Control is performed by using the default value (80°C (176°F).
Engine type: The condition is maintained (when unconfirmed, control is performed by using the default (507F)).
-
Compressor lock judgment by NE.
- Air Conditioning Amplifier
- ECM
- -
NE: Control is performed by using the default value (0 km/h (0 mph)).
-
Air Conditioner (ACN)
Air conditioning system
The electric load control condition is limited according to the load control level.
- Air Conditioning Amplifier
- ECM
- -
Load control: No load control (normal control).
-
- Activation control according to the viscous heater activation permission information.
- Activation control according to the PTC heater activation permission information.
- Air Conditioning Amplifier
- ECM
- -
Permission information: Control is performed according to the operation prohibition state.
-
- Air conditioning system operation status control and panel switch IND output control according to panel switch operation information.
- Exhaust gas automatic air presence judgment and circulation control switching according to exhaust gas automatic air presence information.
- Air Conditioning Amplifier
- Display and navigation module display
- -
None (Air conditioning system operation condition switching is not possible).
-
Air Conditioner (ACN)
Air conditioning system
Dimmer information output to the LIN panel according to the display dimmer information.
- Air Conditioning Amplifier
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
Condition is maintained (after the reset, the dimmer condition is fixed).
-
PTC control switching based on the headlight illumination information.
- Air Conditioning Amplifier
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
PTC control (the headlight flickering countermeasure) is not performed.
-
A/C control pattern switching based on the country specific information.
- Air Conditioning Amplifier
- Accessory Bus Buffer
- -
Condition is maintained (when unconfirmed, control is performed according to the default value).
-
Air conditioning system operation condition switching and the outside temperature display output adjustment according to the vehicle speed information.
- Air Conditioning Amplifier
- Combination Meter
- -
- Decrease in reliability and consistency of the exterior temperature value of the outside temperature display.
- Decrease in the optimum level of A/C vent airflow amount adjustment.
-
Steering Sensor (STR)
Steering angle detection function
The steering angle change information is output to the CAN according to the steering wheel operation.
- Steering Angle Sensor
- Master Cylinder Solenoid (Master Cylinder Solenoid (Skid Control ECU))
- -
- Initialization condition: Data output response request (STS=0).
- When the trigger frame VSC 1S01 is not received from the master cylinder solenoid (skid control ECU), the data output response of the output response request changes from STS=0 to STS=1.
-
- Communication is stopped after transmission is sent 4 times at 12 msec. intervals as the data output response non-request STS=0.
- When the above conditions are met, the sensor internal zero point memory invalid SAZS=1 and SFRZ=previous value + 1 during the next transmission.
-
Depends on the partner ECU specification.
Seat (DST)
Seat system
Memory restore function
- Position Control ECU and Switch
- -
- Position Control ECU and Switch
-
-
- -
- ECM
- -
The memory restore function does not operate.
-
- -
- ECM
- -
The memory restore function does not operate.
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
The memory restore function does not operate.
-
- -
- Outer Mirror Control ECU
- -
The memory restore function does not operate.
-
Memory call function
- Position Control ECU and Switch
- -
- Position Control ECU and Switch
-
-
- -
- Certification ECU (Smart Key ECU)
- -
The memory call does not operate.
-
Tilt and telescopic operation permission function
- Position Control ECU and Switch
- -
- -
-
-
- -
- Multiplex Tilt and Telescopic ECU
- Multiplex Tilt and Telescopic ECU
The tilt and telescopic operation does not operate.
-
M/T recovery operation
- Position Control ECU and Switch
- -
- Position Control ECU and Switch
-
-
- -
- Combination Meter
- -
The recovery does not operate with a manual transmission.
-
Mirror (DRD)
Mirror surface manual control
Function that adjusts the mirror surface with the manual switch.
- Outer Mirror Control ECU
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
The mirror surface manual adjustment function does not operate (stops if there is a disruption during the operation).
-
Mirror surface memory control
Function that records the mirror surface position.
- Outer Mirror Control ECU
- Position Control ECU and Switch, Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
The mirror surface recording function does not operate
-
Mirror surface recovery control
Function that moves the mirror surface to the recorded mirror surface position.
- Outer Mirror Control ECU
- Position Control ECU and Switch
- -
The mirror surface recovery function does not operate (if disrupted during the operation, the function does not operate from the next trigger condition).
-
Mirror surface reverse control
Function that tilts the mirror surface downward when the vehicle is moving in reverse.
- Outer Mirror Control ECU
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus), ECM
- -
The reverse shift-linked function does not operate (if disrupted during the operation, the function does not operate from the next trigger condition).
-
Electric retract/return control
Function that retracts/returns the mirror housing.
- Outer Mirror Control ECU
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus), ECM
- -
The mirror housing retract/return function does not operate (if disrupted during the operation, the function does not operate from the next trigger condition).
-
Foot light illumination control
Function that turns on/off the foot light illumination that is on the bottom of the mirror housing.
- Outer Mirror Control ECU
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
The foot light illumination does not turn on (if illuminated, turns off).
-
Wiper (FRN)
Front wiper control
System that operates the wiper HI and LO operation, vehicle speed sensing intermittent wiper function, vehicle speed switching function, washer linked function, and auto wiper.
- Windshield Wiper ECU
- -
- -
-
-
- -
- ECM
- -
With the ignition switch is ON and the wipers operating with the LO switch on, the intermittent wiper function does not operate while the vehicle is stopped due to vehicle speed switching control not operating.
-
- -
- Main Body ECU (Cowl Side Junction Block LH)
- -
-
- -
- Combination Meter
- -
- With the ignition switch is ON and the wipers operating with the LO switch on, the intermittent wiper function does not operate while the vehicle is stopped due to vehicle speed switching control not operating.
- With the ignition switch is ON, the washer fluid delay timing becomes fixed.
- With the ignition switch is ON, the intervals do not change according to the vehicle speed while the intermittent wiper function is operating.
-
LIN communication control
System that assists the auto wiper function by communication with the rain sensor ECU.
- Windshield Wiper ECU
- -
- -
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH), Accessory Bus Buffer
- -
With the ignition switch is ON, disruption value data is routed to the rain sensor. Otherwise, rain sensor operation depends on specifications.
-
- -
- Combination Meter
- -
-
Navigation (EMVN)
Air Conditioner Control
Controls all Air Conditioner functions
- Display and Navigation Module Display (w/ Navigation System)
- Air Conditioning Amplifier
- -
Clears display screens that do not respond to SW
Displayed on-screen
Clearance Sonar Settings / Communication
Displays Sonar Status, and issues audible warnings
- Display and Navigation Module Display (w/ Navigation System)
- ECM, Parking Assist ECU
- -
Clears display screens that do not respond to SW
Icon disappears
Destination ID
Determines the vehicle destination, and decides the display language, time zones, etc
- Display and Navigation Module Display (w/ Navigation System)
- Main Body ECU (Cowl Side Junction Block LH)
- -
Destination data saved prior to system stoppage is used
Cannot detect
Variable Gear Ratio Steering (VGR)
VGRS system
System that changes the steering gear ratio based on the vehicle speed information and steering angle.
- Steering Control ECU
- -
- Steering Control ECU
-
-
- -
- Steering Angle Sensor
- -
VGRS system does not operate.
Master warning light illuminates and display is shown on multi-information display (meter display).
- -
- ECM
- -
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Clearance Sonar (CSR)
TOYOTA parking assist-sensor system
System that activates the supersonic sensor, measures the distance from obstacles, and notifies the user by using the display and buzzer.
- Clearance Warning ECU
- -
- -
-
-
- -
- Air Conditioning Amplifier
- -
The sonar system functions normally. Maintains distance by maintaining the outside temperature at 25°C (77°F).
-
- -
- Windshield Wiper ECU
- -
The sonar system functions normally. Operates the obstacle judgments with wiper off (except in rain).
-
- -
- ECM
- -
If data received from the ECM is lost, the system is inoperable as control is performed with the shift position data set to P.
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
Does not dim the clearance main switch indicator.
-
The sonar system functions normally. Control is maintained with the country specification information as the previous value (with or without a warning sound).
-
- -
- Combination Meter
- -
If data received from the meter ECU is lost, the system is inoperable as the clearance sonar is controlled at 20 km/h (12.5 mph) or more.
-
Clearance Sonar (CSR)
TOYOTA parking assist-sensor system
System that activates the supersonic sensor, measures the distance from obstacles, and notifies the user by using the display and buzzer.
- -
- Display and navigation module display (w/ Navigation System)
- -
The sonar system functions normally. The clearance sonar customize information is maintained.
-
The sonar system functions normally. Information on the camera presence is maintained.
-
The sonar system functions normally. Notification on the screen that the clearance sonar is off is disabled.
-
Back Guide Monitor
Back guide monitor system
System that displays the expected course lines in the back camera image of the display that links to the steering angle to assist in parking (garage parking, parallel parking, etc.).
- Parking Assist ECU
- -
- -
-
-
- -
- ECM
- -
Back guide monitor system does not operate.
Nothing (informed to user by not displaying image).
- -
- Steering Angle Sensor, Steering Control ECU
- -
Does not display expected course lines on display. Displays "Guidance unavailable" on navigation screen.
Pre-crash Seat Belt (PSB)
PCS (brake linked)
When the VSC system suddenly brakes and/or the vehicle is unable to be controlled (while spinning or drifting), the seat belt control ECU operates the pre-crash seat belts (PSB) that are fastened (receives the buckle switch information from the center airbag sensor) by tightening the seat belts to increase the occupant restraint.
- Seat Belt Control ECU
- -
- Seat Belt Control ECU
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- Combination Meter
Detects that communication with the seat belt control ECU is lost. Control is stopped.
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Detects that communication with the seat belt control ECU is lost. Control is stopped (brake linked).
-
- -
- Center Airbag Sensor
- -
Detects that communication with the seat belt control ECU is lost. Control is stopped.
-
Pre-crash Seat Belt (PSB)
Meter display request
Receives the seat belt control ECU malfunction information or ACC malfunction information, and requests the display of the indicator to the meter ("PCS" indicator turn off/turn on request). - HINT:
- As long as there is a signal in the ACC frame, the blinking request outputs an illumination request to the combination meter. When communication with the ACC frame is lost, there is determined to be a malfunction and an illumination request is output along with the malfunction.
- The priority order is determined by the combination meter. The illumination is the first priority.
- Seat Belt Control ECU
- -
- -
-
-
- -
- -
- -
-
Exclusive indicator "PCS" turns on.
2 digit DTC output
When terminal TC of the DLC3 is connected to terminal GND, a 2 digit DTC (BCD) is displayed by the blinking of "PCS".
- Seat Belt Control ECU
- -
- -
-
-
- -
- ECM
- -
-
-
Meter (MET)
Speedometer
Indicates the vehicle speed according to the vehicle speed signal.
- Combination Meter
- -
- Combination Meter
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
The speedometer indicates 0 km/h (0 mph).
Tachometer
Indicates the engine speed according to the engine speed signal.
- Combination Meter
- -
- Combination Meter
-
- -
- ECM
- -
The tachometer indicates 0 rpm.
ODO/TRIP meter
Calculates and displays the driven distance according to the vehicle speed pulse signal calculated value.
- Combination Meter
- -
- Combination Meter
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
- The ODO/TRIP meter stops calculating and the last displayed value continues to be displayed.
- Optitron meter: In multi-display.
- Regular analog meter: Independent LCD.
-
Engine coolant temperature gauge
Indicates the coolant temperature according to the engine coolant temperature signal.
- Combination Meter
- -
- Combination Meter
-
-
- -
- ECM
- -
The coolant temperature gauge displays less than the C mark.
-
Meter (MET)
Fuel gauge
Indicates the remaining fuel according to the fuel sender (direct line) input (uses the CAN communication (the vehicle speed signal) to determine if the vehicle is being driven or not).
- Combination Meter
- -
- Combination Meter
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Control is performed with the speed input as 0 km/h (0 mph).
-
Oil pressure gauge
Indicates the engine oil pressure according to the oil pressure sender (direct line) input (uses the CAN communication to determine if the engine is on or off by the engine speed signal).
- Combination Meter
- -
- Combination Meter
-
-
- -
- ECM
- -
The oil pressure gauge displays less than the L mark.
-
Shift lever indicator
The shift information is displayed according to the shift position signal.
- Combination Meter
- -
- Combination Meter
-
-
- -
- ECM
- -
The shift lever indicator and shift position display turns off.
Optitron meter: In multi-display.
Regular analog meter: Independent LED, LCD.
-
Meter (MET)
Buzzer
Controls the buzzer to sound and not sound according to the various signals that are input.
- Combination Meter
- -
- Combination Meter
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
The speed warning buzzer does not sound (for Middle East).
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus), Master Cylinder Solenoid (Skid Control ECU)
- -
Conditions for the seat belt buzzer not sounding:
When VSC1S03 is lost: Does not sound.
When BDB1S01 is lost: Does not sound.
When ECT1S90 is lost: Control is performed with B_R=0b.
-
Conditions for the seat belt buzzer sounding:
When VSC1S03 is lost: Control is performed with the vehicle speed as 0 km/h (0 mph).
When VSC1S95 is lost: Control is performed with B_CPKB=0b.
When BDB1S01 is lost: Control is performed with PKB_BDB=0b.
-
The door ajar driving warning buzzer does not sound.
-
Meter (MET)
Buzzer
Controls the buzzer to sound and not sound according to the various signals that are input.
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
The light reminder buzzer does not sound.
-
The sliding roof buzzer condition is maintained (until bus sleep).
-
- -
- ECM
- -
The A/T reverse buzzer does not sound.
-
The sports shift reject buzzer condition is maintained.
-
- -
- 4WD Control ECU
- -
The last state of the 4WD buzzer is maintained.
-
- -
- Certification ECU (Smart Key ECU)
- -
The door control transmitter buzzer (single push, continuous push, and intermittent push) does not sound. The immobiliser verification completion notification buzzer does not sound.
-
Meter (MET)
Telltale
Turns on/blinks/turns off indicators based on the various signals.
- Combination Meter
- -
- Combination Meter
-
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
The ABS indicator turns on.
The ABS indicator turns on.
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus), Master Cylinder Solenoid (Skid Control ECU)
- -
Brake warning light - When VSC1S95 is lost: Illuminates.
- When BDB1S01 is lost: Control is performed with PKB_BDB=0b.
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
The SLIP indicator condition is maintained.
The VSC OFF indicator condition is maintained.
The downhill assist control indicator condition is maintained.
The slight low speed TRC indicator condition is maintained.
-
120 km/h (75 mph) speed warning turns off (for Middle East).
-
Control is performed with the speed condition as 0 km/h (0 mph) for the following display: FUEL FILTER clog indicator.
The odometer calculation is stopped for the following display conditions: T-BELT indicator.
-
Meter (MET)
Telltale
Turns on/blinks/turns off indicators based on the various signals.
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
When there is determined to be a disruption, the following indicators operate as follows:
While the ignition switch is ON: Condition is maintained.
When the ignition switch is OFF: Turns off.- Door indicator
- Driver side seat belt indicator
-
When there is determined to be a disruption, the following indicators operate as follows:
While the ignition switch is ON: Condition is maintained.
When the ignition switch is OFF: Turns off.- Front FOG indicator
- Rear FOG indicator
- TAIL indicator
- HEAD indicator
- BEAM indicator
-
- -
- Parking Assist ECU
- -
The clearance sonar indicator turns off.
-
- -
- ECM
- -
The A/T OIL TEMP indicator condition is maintained.
The ECT POWER indicator condition is maintained.
The 2nd STRT indicator condition is maintained.
The CHARGE indicator condition is maintained.
The CRUISE indicator condition is maintained.
The GLOW indicator condition is maintained.
-
Meter (MET)
Telltale
Turns on/blinks/turns off indicators based on the various signals.
- -
- ECM, 4WD Control ECU
- -
The A/T P indicator light conditions are maintained.
-
- -
- 4WD Control ECU
- -
The CTR DIFF indicator turns off.
The Rear DIFF indicator turns off.
The 4LO indicator turns off.
-
- -
- Seat Belt Control ECU
- -
The PCS indicator condition is maintained.
-
- -
- Center Airbag Sensor
- -
The SRS warning indicator turns on.
The SRS warning indicator turns on.
Meter (MET)
Multi-display
Displays information about the drive monitor, warning, radar cruise, clearance sonar, door, A/T shift position, 4-WHEEL AHC, odometer, etc. based on the various signals.
- Combination Meter
- -
- Combination Meter
-
-
- -
- ECM, Master Cylinder Solenoid (Skid Control ECU)
- -
Displays a blank screen and drive monitor operation and calculation of the following values stops: instant fuel economy, average fuel economy after refueling, distance to empty, average vehicle speed after engine start, driving distance after engine start.
-
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Parking brake drag warning display conditions:
When VSC1S03 is lost: Control is performed with the vehicle speed as 0 km/h (0 mph).
When VSC1S95 is lost: Control is performed with B_CPKB=0b.
When BDB1S01 is lost: Control is performed with PKB_BDB=0b.
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus), Master Cylinder Solenoid (Skid Control ECU)
- -
The TRC system display is maintained.
The VSC display is maintained.
-
Meter (MET)
Multi-display
Displays information about the drive monitor, tire pressure, warning, clearance sonar, door, A/T shift position, 4-WHEEL AHC, odometer, etc. based on the various signals.
- -
- Master Cylinder Solenoid (Skid Control ECU)
- -
Control is performed with the speed condition as 0 km/h (0 mph) for the following displays: Door open while driving display, FUEL FILTER clog display.
ODO calculation stops for the following display conditions: Oil maintenance display, T-BELT display.
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus), Master Cylinder Solenoid (Skid Control ECU)
- -
Conditions for the door open display and door open while driving display:
VSC1S03: Control is performed with the vehicle speed as 0 km/h (0 mph).
BSB1S01: Display state is maintained.
BDB1S08: No display.
-
- -
- Air Conditioning Amplifier
- -
The outside temperature display is "E".
The outside temperature display is "E" (in the meter).
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
The shift position display turns off.
-
The door control transmitter display condition is as follows:
While the ignition switch is ON: Condition is maintained.
When the ignition switch is OFF: Turns off.
-
The sliding roof open display condition is as follows:
While the ignition switch is ON: Condition is maintained.
When the ignition switch is OFF: Turns off.
-
Meter (MET)
Multi-display
Displays information about the drive monitor, tire pressure, warning, clearance sonar, door, A/T shift position, 4-WHEEL AHC, odometer, etc. based on the various signals.
- -
- Parking Assist ECU
- -
The clearance sonar display state is maintained.
-
- -
- ECM
- -
The A/T shift position display turns off.
-
The A/T OIL TEMP display state is maintained.
-
- -
- Seat Belt Control ECU
- -
The PCS display condition is maintained.
-
- -
- Certification ECU (Smart Key ECU)
- -
The door control transmitter display condition is maintained.
The security display condition is maintained.
The door control transmitter unlock mode display condition is maintained.
-
- -
- Suspension Control ECU
- -
4-WHEEL AHC vehicle height display turns off and "Check 4-WHEEL AHC System" is displayed.
4-WHEEL AHC vehicle height display turns off and "Check 4-WHEEL AHC System" is displayed (in the meter).
- -
- Steering Control ECU
- -
"Check VGRS System" is displayed
"Check VGRS System" is displayed (in the meter).
Illumination function
Controls dimming and meter illumination on/off according to the CAN signals.
- Combination Meter
- -
- Combination Meter
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
Optitron meter: Daytime brightness.
Analog meter: The illumination turns on.
-
- -
- ECM
- -
-
-
Meter (MET)
Passenger seat belt warning indicator
Blinks the passenger seat belt warning indicator according to the CAN signals.
- Combination Meter
- -
- -
-
-
- -
- Center Airbag Sensor
- -
The passenger seat belt warning indicator condition is maintained.
-
- -
- -
- Display and navigation module display (w/ Navigation System)
-
-
Body (BDB)
Power supply switching control
The system that switches the power supply between +B, ACC, and IG.
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- Combination Meter, ECM, Accessory Bus Buffer
- -
The forced ignition switch OFF function does not operate.
-
When the power supply switching conditions are met, power supply switching control is permitted.
When the power supply condition IG2 start/stop switch turns from off to on, the power supply condition is changed to IG1, and the IG relay output stops.
-
Body (BDB)
Security
The system that operates the warning when a theft is detected.
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- Certification ECU (Smart Key ECU)
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
The security control does not operate
(The headlight/taillight warning output, horn warning light output, and hazard warning light output do not operate).
The forced door lock function lock output does not operate.
The dome light warning control does not operate.
The lighting system answer back control does not operate.
(The taillight warning output and hazard warning light output do not operate).
-
When the security warning is operating, warning output stops during hazard warning light output.
-
When the security warning is operating, the dome light turns off during dome light illumination.
-
Entry and start/Wireless
The system that operates the lock/unlock, ignition switch, back door opener, warning, etc. by pressing the switch when the door control transmitter is within the vehicle detection area.
The system that operates the vehicle lock/unlock, panic, back door opener, etc. by remote control.
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- Certification ECU (Smart Key ECU)
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
Entry and start/wireless control does not operate.
The door lock/unlock control and entry back door opener control do not operate.
-
Body (BDB)
Vehicle speed linked auto lock
The system that locks the doors when the vehicle speed is 26 km/h (16 mph) or more.
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- Combination Meter, ECM
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
When the vehicle speed linked auto lock signal is lost, operation is permitted.
-
The vehicle speed linked auto lock does not operate.
-
Shift linked auto lock/unlock
The system that unlocks all the doors when the shift lever is moved to P while the vehicle speed is 16 km/h (10 mph) or less, and locks all the doors when the shift lever is moved from P to another position while the engine is running.
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- Combination Meter, ECM
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
The shift linked auto lock/unlock function does not operate.
-
When the shift linked auto lock/unlock signal is lost, operation is permitted.
-
DRL
The system that illuminates lights when driving the vehicle to improve the visibility of pedestrians and other vehicles in the daytime.
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- ECM
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
DRL control does not operate. - HINT:
- If operated once, the operation continues until the ignition switch is turned OFF, even if the signal is lost.
-
Body (BDB)
Back door opener
The system that releases the door latch (turns opener motor on) by turning on the switch built into the outside door handle.
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- Combination Meter
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
Prohibits the back door opener control.
-
Accessory Control
The system that controls accessories including wireless door lock, lighting system answer back, and engine starter.
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- Accessory Bus Buffer
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- Wireless door lock accessory control does not operate:
- Wireless door lock/unlock accessory control does not operate.
- Smart unlock accessory control does not operate.
- Auto lock/unlock accessory control does not operate.
- Lighting system answer back accessory control does not operate:
- Hazard light blink request does not operate.
- While hazard light blink request is being sent, hazard lamps turn off.
- Engine starter accessory control does not operate.
-
Power window
The system that operates the power window control based on the request from wireless/entry and start control.
- Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- Certification ECU (Smart Key ECU)
- -
Power window control does not operate.
Power window control stops during wireless/entry power window control operation.
-
Accessory Remote Starter
Engine Start 1
Sends immobilizer release requests using bidirectional communication with the Certification ECU (Smart Key ECU)
- -
- Certification ECU (Smart Key ECU)
- -
Unable to perform engine start control.
-
Engine Start 2
Sends power supply (IG, ACC) ON/OFF requests.
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
The engine turns off.
-
Door Lock/Unlock
Sends door lock/unlock requests
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
Sending of door lock/unlock requests is prohibited.
-
Car Finder
Sends hazard flasher requests
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
Sending of hazard flasher requests is prohibited.
-
Vehicle Registration
Performs remote start registration using bidirectional communication with the Certification ECU (Smart Key ECU)
- -
- Certification ECU (Smart Key ECU)
- -
Performing remote start vehicle registration is prohibited.
-
Air Conditioning Control
Sends automatic air conditioning/defogger control requests.
- -
- Air Conditioning Amplifier
- -
Auto air conditioner/defogger control is prohibited.
-
Verification (IDT)
Entry function
Entry and start/lock/back door/warning, etc.
- Certification ECU (Smart Key ECU)
- -
- -
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus), Main Body ECU (Cowl Side Junction Block LH) (V Bus)
- -
- The entry lock/unlock does not operate.
- The entry back door does not operate.
- The entry and start warning message does not operate.
- The key lock-in prevention function does not operate.
- The entry illumination does not operate.
-
Package default setting.
-
- -
- Combination Meter
- -
The vehicle speed is determined to be 0 km/h (0 mph).
-
-
-
Wireless buzzer function
The wireless buzzer sounding control.
- Certification ECU (Smart Key ECU)
- -
- -
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
Does not sound even though there is a wireless buzzer request.
-
Package default settings.
-
Immobiliser function
The immobiliser control by the warning and remote engine start.
- Certification ECU (Smart Key ECU)
- -
- -
-
-
- -
- Accessory Bus Buffer
- -
Accessory remote starter does not operate.
-
- -
- ECM
- -
The ignition switch is forcibly turned off.
-
Wireless function
Wireless electric wave information transmission.
- Certification ECU (Smart Key ECU)
- -
- -
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
-
-
Verification (IDT)
Security function
Security alarm control.
- Certification ECU (Smart Key ECU)
- -
- -
-
-
- -
- Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
- -
The alarm is not unset.
The alarm is not set.
-
- -
- ECM
- -
The alarm is not unset by the engine start.
-
Movement Control Bus (CGW)
Movement control bus monitor function
Monitoring of communication stop.
- Network Gateway ECU (Movement Control Bus)
- Seat Belt Control ECU
- -
The reception interval counter (RAM and CAN controller initialization).
-
- Network Gateway ECU (Movement Control Bus)
- Clearance Warning ECU
- -
- Network Gateway ECU (Movement Control Bus)
- Parking Assist ECU
- -
- Network Gateway ECU (Movement Control Bus)
- Steering Angle Sensor
- -
- Network Gateway ECU (Movement Control Bus)
- Suspension Control ECU
- -
- Network Gateway ECU (Movement Control Bus)
- Master Cylinder Solenoid (Skid Control ECU)
- -
- Network Gateway ECU (Movement Control Bus)
- Yaw Rate Sensor
- -
- Network Gateway ECU (Movement Control Bus)
- Steering Control ECU
- -
- Network Gateway ECU (Movement Control Bus)
- 4WD Control ECU
- -
- Network Gateway ECU (Movement Control Bus)
- Clearance Warning ECU, Master Cylinder Solenoid (Skid Control ECU), 4WD Control ECU, Steering Angle Sensor, Yaw Rate Sensor, Steering Control ECU, Seat Belt Control ECU, Parking Assist ECU, Suspension Control ECU
- -
- Control Master