2011-2013 Land Cruiser · Service Manual Steering

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


REMOVE LOWER STEERING COLUMN COVER

  1. C172704
    Remove the 3 screws.

    HINT:
    Turn the steering wheel to the right and left as necessary to remove the 2 screws.

  1. C172708
    Detach the 2 claws to remove the lower steering column cover.


REMOVE UPPER STEERING COLUMN COVER
  1. Detach the 4 clips.

  1. C172706
    Detach the claw to remove the upper steering column cover.


REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Remove the driver side knee airbag assembly (Click here).


INSPECT TILT MOTOR

  1. Inspect the tilt motor.

    1. Disconnect connector A from the multiplex tilt and telescopic ECU.

    2. C172660E03
      Apply battery voltage to the tilt motor connector, and check the steering wheel tilt operation.
      OK 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (TIM+)
      Battery negative (-) → Terminal 1(TIM-)
      Steering wheel tilts up

    3. C172660E04
      Apply battery voltage to the tilt motor connector, and check the steering wheel tilt operation.
      OK 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (TIM-)
      Battery negative (-) → Terminal 10 (TIM+)
      Steering wheel tilts down
      If the steering wheel does not tilt down, replace the steering column assembly.


INSPECT TELESCOPIC MOTOR

  1. Inspect the telescopic motor.

    1. Disconnect connector B from the multiplex tilt and telescopic ECU.

    2. C172661E01
      Apply battery voltage to the telescopic motor connector, and check the steering column operation.
      OK 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2 (TEM+)
      Battery negative (-)→ Terminal 6 (TEM-)
      Steering column contracts

    3. C172661E03
      Apply battery voltage to the telescopic motor connector, and check the steering column operation.
      OK 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (TEM-)
      Battery negative (-) → Terminal 2 (TEM+)
      Steering column extends
      If the steering column operation does not match the specified condition, replace the steering column.


INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Install driver side knee airbag assembly (Click here).


INSTALL LOWER STEERING COLUMN COVER

  1. C172708
    Attach the 2 claws to install the lower steering column cover.


INSTALL UPPER STEERING COLUMN COVER

  1. C172706
    Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips to install the upper steering cover onto the instrument panel cluster finish panel.

  1. C172704
    Install the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

    HINT:
    Turn the steering wheel to the right and left as necessary to install the 2 screws.


INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).


CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← COMPONENTS (from Sep 2011)ON-VEHICLE INSPECTION (from Jan 2012) →