2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL REAR SEATBACK HEATER ASSEMBLY
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new tack pins.

    B181208E01


2. INSTALL REAR SEPARATE TYPE SEATBACK COVER

  1. B184037E01
    w/ Center Armrest:
    Using hog ring pliers, install the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B189167E01
    w/o Center Armrest:
    Using hog ring pliers, install the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B184024
    w/ Rear Seat Side Airbag:
    Connect the seatback cover bracket to the seatback pad.


3. INSTALL SEATBACK COVER WITH PAD
  1. Install the seatback cover with pad.

  1. B184030
    w/ Center Armrest:
    Pull out the seat belt.

  1. B189169
    w/o Center Armrest:
    Pull out the seat belt.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:
    Pass the seatback heater wire harness through the hole in the seatback.

    1. B184057

    2. B182598E01
      Connect the seatback heater wire harness and install a new cable tie.

  1. B184020
    w/ Rear Seat Side Airbag:
    Install the seatback cover bracket to the seat frame with the cap nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

  1. B262669E01
    w/ Center Armrest:
    Using hog ring pliers, install new hog rings to the seatback frame.

  1. B262670E01
    w/o Center Armrest:
    Using hog ring pliers, install new hog rings to the seatback frame.


4. INSTALL REAR SEAT BELT HOLE COVER LH

B181239
  1. Attach the 4 claws to install the cover.

  1. Install the screw.


5. INSTALL SHOULDER BELT ANCHOR COVER

B184040
  1. Attach the 2 claws to install the cover.


6. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

  1. B181190
    w/ Center Armrest:
    Attach the 4 claws to install the 2 supports.

  1. B181243
    w/o Center Armrest:
    Attach the 8 claws to install the 4 supports.


7. INSTALL REAR SEAT HEADREST ASSEMBLY

8. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

  1. B184026
    w/ Center Armrest:

    1. Push the board down to attach the 2 claws on the bottom.

    2. Attach the 2 claws on the top of the board to install it.

  1. B189166
    w/o Center Armrest:

    1. Push the board down to attach the 3 claws on the bottom.

    2. Attach the 3 claws on the top of the board to install it.


9. INSTALL REAR SEATBACK COVER

B182667
  1. Attach the 4 claws to install the cover.


10. INSTALL SEAT CUSHION COVER WITH PAD
  1. Install the seatback cover with pad.

  1. B184030
    w/ Center Armrest:
    Pull out the seat belt.

  1. B189169
    w/o Center Armrest:
    Pull out the seat belt.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seatback.

  1. w/ Seat Heater System:
    Pass the seatback heater wire harness through the hole in the seatback.

    1. B184057

    2. B182598E01
      Connect the seatback heater wire harness and install a new cable tie.

  1. B184020
    w/ Rear Seat Side Airbag:
    Install the seatback cover bracket to the seat frame with the cap nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

  1. B262669E01
    w/ Center Armrest:
    Using hog ring pliers, install new hog rings to the seatback frame.

  1. B262670E01
    w/o Center Armrest:
    Using hog ring pliers, install new hog rings to the seatback frame.


11. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B184533E01
  1. Connect the belt anchor.

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.


12. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B184532E01
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    HINT:
    The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.


13. INSTALL REAR SEAT UNDER TRAY COVER LH

B181181
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


14. INSTALL REAR SEAT CUSHION COVER RH

B181231
  1. Attach the 2 claws to install the cover.

  1. Install the 4 screws.


15. INSTALL REAR UNDER SIDE COVER LH

B181230
  1. Attach the 2 claws and 2 clips to install the cover.

  1. Install the 5 screws.

  1. B181229
    Attach the 10 claws.


16. INSTALL REAR SEATBACK STAY COVER LH

B181226
  1. Attach the 2 claws to install the cover.

  1. Install the screw.


17. INSTALL SEAT BELT ANCHOR COVER CAP

  1. B181228
    Install the anchor cover cap with the screw.

  1. B184029
    Attach the claw to close the cap.


18. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


19. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

  1. B181176
    Attach the cable clamp to connect the cable.

  1. B184045
    Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear Seat Side Airbag:
    Attach the wire harness clamp.

  1. w/ Seat Heater System:
    Attach the wire harness clamp.


20. INSTALL REAR NO. 2 SEAT PROTECTOR
  1. Install the wire harness, and attach 2 claws to close the protector.

  1. B182595
    Attach the claw to install the protector to the seat hinge.

  1. Install the clip.

  1. B184016
    w/ Rear Seat Side Airbag:
    Attach the claw to install the wire harness connector.

  1. w/ Seat Heater System:
    Attach the claw to install the wire harness connector.


21. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

  1. B184044
    Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

  1. B181224
    Attach the 4 claws to install the seat leg side cover.

  1. Install the 4 screws.


22. INSTALL UPPER SEAT TRACK RAIL COVER RH

B184041
  1. Attach the 2 claws to install the cover.


23. INSTALL UPPER SEAT TRACK RAIL COVER LH

B184028
  1. Attach the 2 claws to install the cover.


24. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B184015
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


25. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B184027E01
  1. Attach the 3 claws in the order shown in the illustration to install the cover.

  1. Install the 2 screws.


26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B184013
  1. Install the release handle with the screw.


27. INSTALL SEAT ADJUSTER BOLT COVER

B184012
  1. Attach the 2 claws to install the cover.


28. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
  1. Install the rear No. 1 seat assembly (Click here).

← INSPECTION (from Sep 2011)INSTALLATION (from Jan 2012) →