2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT CIRCUIT OPENING RELAY (C/OPN)

  1. A188757E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT INTEGRATION RELAY (IG2)
  1. Measure the resistance of the IG2 MAIN fuse.

    1. Remove the IG2 MAIN fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      IG2 MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the IG2 MAIN fuse.

    3. Install the IG2 MAIN fuse to the integration relay.

  1. A225101E06
    Measure the resistance of the ignition relay No. 2 (IG2) circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-8
      Battery voltage is not applied to terminals 1B-6 and 1B-7
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-6 and 1B-7
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.


INSPECT INTEGRATION RELAY (EFI)
  1. Measure the resistance of the EFI MAIN fuse.

    1. Remove the EFI MAIN fuse from the integration relay

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the EFI MAIN fuse.

    3. Install the EFI MAIN fuse to the integration relay.

  1. A225101E06
    Measure the resistance of the EFI relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      Battery voltage is not applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-2 and 1B-3
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.


INSPECT EFI NO. 2 RELAY

  1. A188757E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT INTEGRATION RELAY (A/F)
  1. Measure the resistance of the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the A/F fuse.

    3. Install the A/F fuse to the integration relay.

  1. A225101E07
    Measure the resistance of the A/F sensor heater relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      Battery voltage is not applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1 A-2 and 1A-3
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.


INSPECT MAIN BODY ECU (IG1 NO. 1)

  1. Measure the resistance according to the value(s) in the table below.

    A180292E02

    Text in Illustration 
    *a
    Component without harness connected
    (Main Body ECU)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2A-1 - 2B-17
    Battery voltage is not applied to terminals 2B-5 and 2D-43
    10 kΩ or higher
    Battery voltage is applied to terminals 2B-5 and 2D-43
    Below 1 Ω

    If the result is not as specified, replace the main body ECU.


INSPECT STARTER RELAY (ST)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the starter relay.


INSPECT STARTER CUT RELAY (ST CUT)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the starter relay.


INSPECT MAIN BODY ECU (ACC RELAY)

A180124E02
Text in Illustration 
*a
Component without harness connected
(Main Body ECU)
-
-
  1. Measure the resistance of the ACC relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2A-1 - 2D-8
      Battery voltage not applied between 2D-45 and 2D-62
      10 kΩ or higher
      Battery voltage applied between 2D-45 and 2D-62
      Below 1 Ω

      If the result is not as specified, replace the main body ECU.

← INSTALLATION (from Jan 2012)ON-VEHICLE INSPECTION (from Jan 2012) →