2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011


INSPECT CIRCUIT OPENING RELAY (C/OPN)

  1. A184106E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT INTEGRATION RELAY (IG2)
  1. Measure the resistance of the IG2 MAIN fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      IG2 MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the IG2 MAIN fuse.

  1. A106666E15
    Measure the resistance of the ignition relay No. 2 (IG2) circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-8
      Battery voltage is not applied to terminals 1B-6 and 1B-7
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-6 and 1B-7
      Below 1 Ω

      If the result is not as specified, replace the integration relay.


INSPECT INTEGRATION RELAY (EFI)
  1. Measure the resistance of the EFI MAIN fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the EFI MAIN fuse.

  1. A106666E15
    Measure the resistance of the EFI relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      Battery voltage is not applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-2 and 1B-3
      Below 1 Ω

      If the result is not as specified, replace the integration relay.


INSPECT EFI NO. 2 RELAY (EFI NO. 2)

  1. A184106E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT INTEGRATION RELAY (A/F)
  1. Measure the resistance of the A/F fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the A/F fuse.

  1. A106666E16
    Measure the resistance of the A/F sensor heater relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      Battery voltage is not applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1A-2 and 1A-3
      Below 1 Ω

      If the result is not as specified, replace the integration relay.


INSPECT MAIN BODY ECU (IG1 NO. 1)

  1. Measure the resistance according to the value(s) in the table below.

    A180292E01

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    2A-1 - 2B-17
    Battery voltage is not applied to terminals 2B-5 and 2D-43
    10 kΩ or higher
    Battery voltage is applied to terminals 2B-5 and 2D-43
    Below 1 Ω

    If the result is not as specified, replace the cowl side junction block LH.


INSPECT STARTER RELAY (ST)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT STARTER CUT RELAY (ST CUT)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT MAIN BODY ECU (ACC RELAY)

A180124E01
  1. Measure the resistance of the ACC relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2A-1 - 2D-8
      Battery voltage not applied between 2D-45 and 2D-62
      10 kΩ or higher
      Battery voltage applied between 2D-45 and 2D-62
      Below 1 Ω

      If the result is not as specified, replace the main body ECU.

← INSTALLATION (Sep 2011 – Dec 2011)PRECAUTION (from Jan 2012) →