2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT AIR PUMP HEATER RELAY (AI-PMP HTR)

  1. A184106E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT AIR INJECTION VSV RELAY (AI-VSV)

  1. A184106E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT INTEGRATION RELAY (IG2)
  1. Measure the resistance of the IG2 MAIN fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      IG2 MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the IG2 MAIN fuse.

  1. Measure the resistance of the ignition relay No. 2 (IG2) circuit.

    1. A106666E24
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-8
      Battery voltage is not applied to terminals 1B-6 and 1B-7
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-6 and 1B-7
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.


INSPECT INTEGRATION RELAY (EFI)
  1. Measure the resistance of the EFI MAIN fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the EFI MAIN fuse.

  1. Measure the resistance of the EFI relay circuit.

    1. A106666E24
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      Battery voltage is not applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-2 and 1B-3
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.


INSPECT EFI NO. 2 RELAY (EFI NO. 2)

  1. A184106E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT INTEGRATION RELAY (A/F)
  1. Measure the resistance of the A/F fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the A/F fuse.

  1. Measure the resistance of the A/F sensor heater relay circuit.

    1. A106666E24
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      Battery voltage is not applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1 A-2 and 1A-3
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Integration Relay)
      If the result is not as specified, replace the integration relay.


INSPECT MAIN BODY ECU (IG1 NO. 1)

A180292E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2A-1 - 2B-17
    Battery voltage is not applied to terminals 2B-5 and 2D-43
    10 kΩ or higher
    Battery voltage is applied to terminals 2B-5 and 2D-43
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Main Body ECU)
    If the result is not as specified, replace the cowl side junction block LH.


INSPECT STARTER RELAY (ST)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT STARTER CUT RELAY (ST CUT)

  1. B060778E26
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the relay.


INSPECT MAIN BODY ECU (ACC RELAY)

A180124E01
  1. Measure the resistance of the ACC relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2A-1 - 2D-8
      Battery voltage not applied between 2D-45 and 2D-62
      10 kΩ or higher
      Battery voltage applied between 2D-45 and 2D-62
      Below 1 Ω

      If the result is not as specified, replace the main body ECU.

← ON-VEHICLE INSPECTION (Sep 2011 – Dec 2011)PRECAUTION (from Jan 2012) →