2011-2013 Land Cruiser · Service Manual General

INITIALIZATION

Troubleshooting · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL
Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal 
Necessary Procedure
Procedure Details
Effect or Inoperative Function when Necessary Procedure is not Performed
Notes
Initialize parking assist monitor system
Perform either of the following procedures.
  1. Fully turn the steering wheel to the right and left.
  2. Drive the vehicle at more than 20 km/h (12 mph) for more than 5 minutes on a straight road with as little traffic congestion as possible.
Parking assist function
-
Servo motors initialization
Using the intelligent tester, perform the servo motor initialization.
Air conditioning system does not operate properly
During initialization, the AUTO indicator light comes on, and then goes off when initialization has finished.
Initialization of power back door system
Completely close the back door by hand once.
Power back door function
Initialization is not necessary if the cable is disconnected and reconnected to the negative (-) battery terminal while the back door is closed. However, the power back door system will not operate if the back door is not unlocked after the cable is reconnected.

NOTICE:
After the engine switch is turned off, the multi-media module receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least a minute before disconnecting the cable from the negative (-) battery terminal.


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Procedures Necessary when ECU or Other Parts are Replaced 
Replacement Part
Necessary Procedures
Effects / Inoperative Functions When Necessary Procedures are not Performed
Notes
ECM (1VD-FTV, w/ DPF)
  1. Learning values save
  2. Learning values write
Engine starting
-
Engine assembly (1VD-FTV, w/ DPF)
  1. Clear Crank Time Compensation Data
  2. Injector compensation code registration
  3. Pilot quantity learning
Engine starting
-
Crankshaft position sensor plate (1VD-FTV, w/ DPF)
Clear crank time compensation data
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
-
Air fuel ratio sensor (1VD-FTV, w/ DPF)
Clear A/F sensor compensation data
EGR volume is affected
-
Fuel supply pump (1VD-FTV, w/ DPF)
Supply pump initialization
Engine startability
-
1VD-FTV, w/ DPF
  1. Front exhaust pipe assemblies (DPF catalytic converter)
  2. Monolithic converter assemblies (CCo catalytic converter)
  1. Clear DPF thermal deterioration data
  2. Learning values write
Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement
-
Fuel injector (1VD-FTV, w/ DPF)
  1. Injector compensation code registration
  2. Pilot quantity learning
DTC P062F is output
-
Fuel injector (1VD-FTV, w/o DPF)
Injector compensation code registration
DTC P1601 is output
-
Fuel supply pump (1VD-FTV, w/o DPF)
ECM initialization
Engine starting
-
ECM (1VD-FTV, w/o DPF)
ECU communication ID registration
Engine starting
-
Distance control ECU
Initialization
Cannot adjust millimeter wave radar sensor
-
Millimeter wave radar sensor assembly
Adjusting the radar beam axis
Dynamic radar cruise control system does not operate normally
-
Any of shift solenoid valves
Reset memory
Large shift shock
-
Transmission wire
Add and adjust the ATF level
Automatic transmission assembly damaged
-
Valve body assembly
Add and adjust the ATF level
Automatic transmission assembly damaged
-
Reset memory
Large shift shock
-
Oil cooler and oil cooler tube
Add and adjust the ATF level
Large shift shock
-
Park/neutral position switch
Adjust the park/neutral position switch
  1. Back-up light does not turn on
  2. Meter indicator display malfunction
  3. Vehicle undrivable
  4. Shifting not possible
-
Transmission floor shift assembly
Adjust the shift lever position
  1. Back-up light does not turn on
  2. Meter indicator display malfunction
  3. Vehicle undrivable
  4. Shifting not possible
-
Automatic transmission assembly
Add and adjust the ATF level
Automatic transmission assembly damaged
-
Reset memory
Large shift shock
-
  1. Clutch pedal (for LHD)
  2. Clutch master cylinder (for LHD)
Inspect and adjust clutch pedal
  1. Clutch slips
  2. Clutch dies not disengage
-
  1. Clutch pedal (for RHD)
  2. Clutch master cylinder (for RHD)
Inspect and adjust clutch pedal
  1. Clutch slips
  2. Clutch dies not disengage
-
Suspension control ECU
Vehicle height offset calibration
Vehicle height sensor date may be affected due to installation position, or vehicle height recognition may be erroneous
After vehicle height offset calibration is performed, it is necessary to calibrate the yaw rate sensor
Height control sensor
Vehicle height offset calibration
Vehicle height sensor date may be affected due to installation position, or vehicle height recognition may be erroneous
After vehicle height offset calibration is performed, it is necessary to calibrate the yaw rate sensor
  1. Suspension
  2. Underbody components
  1. Steering angle neutral point in memory
  2. Yaw rate and G sensor zero point calibration
  1. The brake control and dynamic control systems do not operate properly
  2. VGRS system
  3. Parking assist monitor system
Removed/installed or replaced
Skid control ECU (Master cylinder solenoid)
Deceleration sensor zero point calibration
The brake control system does not operate properly
-
Deceleration sensor
  1. Clearing zero point calibration data
  2. Deceleration sensor sensor zero point calibration
The brake control system does not operate properly
-
Skid control ECU (Master cylinder solenoid)
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
The brake control and dynamic control systems do not operate properly
-
Yaw rate sensor assembly
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
The brake control and dynamic control systems do not operate properly
-
Vehicle height adjustment
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
  3. Steering sensor initialization
The brake control and dynamic control systems do not operate properly
w/ active height control system
  1. Brake pedal
  2. Hydraulic brake booster
Check brake pedal height
  1. Brake performance problem
  2. Delayed stop light illumination or continuous illumination
-
  1. Parking brake lever
  2. Parking brake cable
  3. Parking brake assembly
Adjust parking brake lever travel
  1. Brake drag
  2. Brake performance problem
  3. Delayed stop light illumination or continuous illumination
-
  1. Steering control ECU
  2. Steering column
  3. Steering intermediate shaft
  4. Steering actuator assembly
Calibration
  1. VGRS system
  2. DTC output
-
Steering angle sensor
Initialization
  1. VGRS system
  2. Other related systems cannot operate properly
-
Steering column
Steering off center adjustment
Steering system does not operate normally
-
Multi-media module receiver assembly (w/ G-BOOK system)
Vehicle contract setting
G-BOOK service
If the multi-media module receiver assembly is replaced on vehicles that do not have a contract for the G-BOOK service, perform the vehicle contract setting.
Rear television camera
Rear television camera optional axis (Camera position setting)
Vehicle width extension lines and expected course are deviated
Replace or installation angle of the rear television camera changes because of the removal and installation of the rear television camera
Side television camera
Side television camera optional axis (Camera position setting)
Vehicle parallel lines and expected course are deviated
Replace or installation angle of the side television camera changes because of the removal and installation of the side television camera
Parking assist ECU
  1. Steering angle neutral point in memory
  2. Store the left and right maximum steering angles
  3. Rear television camera optical axis (Camera position setting)
  4. Side television camera optical axis (Camera position setting)
Parking assist monitor system
Replace or installation angle of the rear television camera changes because of the removal and installation of the rear television camera
w/ Entry and Start System:
  1. ID code box
  2. Steering lock ECU
  3. Key
  4. Certification ECU
Registration
  1. Wireless door lock operation
  2. Entry operation
  3. Engine starting
  4. Steering unlock
Refer to the Service Bulletin for the registration procedure.
w/o Entry and Start System:
  1. Transponder key ECU
  2. ECM
  3. Key
Registration
Engine starting
Refer to the Service Bulletin for the registration procedure.
w/o Entry and Start System:
  1. Door control transmitter
  2. Door control receiver
Register recognition code
Wireless door lock operation
-
Servo motors
Servomotors initialization
Air conditioning system does not operate properly
During initialization, the AUTO indicator light comes on, and then goes off when initialization has finished.
for Models with Jam Protection Function on 4 Windows:
  1. Front Power window regulator motor LH
  2. Front Power window regulator motor RH
  3. Rear Power window regulator motor LH
  4. Rear Power window regulator motor RH
Initialize the motor
  1. Auto Operation
  2. Jam protection function
  3. Power window control system (for Models with Jam Protection Function on 4 Windows)
-
for Models with Jam Protection Function on Driver Door Window Only:
  1. Front Power window regulator motor LH (for LHD)
  2. Front Power window regulator motor RH (for RHD)
Initialize the motor
  1. Auto Operation
  2. Jam protection function
  3. Power window control system (for Models with Jam Protection Function on Driver Door Window Only)
-
Inner rear view mirror
  1. Compass zone setting
  2. Compass calibration
  3. Register transmitter code
Direction is not displayed correctly
-
  1. Sliding roof driver gear (Sliding roof ECU)
  2. Sliding roof glass
Initialize sliding roof system
  1. Auto operation
  2. Jam protection function
  3. Sliding roof operation after engine switch OFF
  4. Wireless door lock control function
  5. Key-linked operation function (Driver side door only)
  6. Entry lock switch-linked operation
-
  1. Power back door unit
  2. Back door lock
Initialize sliding roof system
Power back door system
-
w/ Static Headlight Auto Leveling
  1. Headlight leveling ECU
  2. Height control sensor LH
Initialization
Headlight leveling function
-
w/ Dynamic Headlight Auto Leveling, w/o Active Height Control Suspension
  1. Headlight swivel ECU
  2. Height control sensor LH
Initialization
Headlight leveling function
-
Headlight assembly
Adjustment
Beam axis deviation
-
Fog light assembly
Adjustment
Beam axis deviation
-
Front bumper
Adjustment
Beam axis deviation
-

REGISTRATION RELATED TO ECD SYSTEM (w/ DPF)

  1. LEARNING VALUES CONFIRMATION
    This procedure uses the GTS to display the learned values (injector compensation code, pilot quantity initial learning value, pilot quantity deterioration learning value, pilot quantity current learning value, pilot quantity learning value, crank time compensation learning value, A/F sensor learning value and catalyst deterioration learning value) stored in the ECM.
    A265488E01

    HINT:

    1. A204047
      A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Engine and ECT / Utility / Learning values confirmation.

    4. A266977
      Press "Next".

    5. A266978
      Press "Next" again to proceed.

    6. A266979
      Select the value to confirm and press "Next".

    7. When the next screen is displayed, confirm the contents and press "Exit".
      A266980

  2. LEARNING VALUES SAVE
    This procedure uses the GTS to save the learned values (injector compensation code, pilot quantity learning value, crank time compensation learning value, catalyst deterioration learning value and A/F sensor learning value) stored in the ECM in the GTS depending on the components being replaced.
    A209877E03

    HINT:
    1. When replacing the engine assembly, injector assembly, front exhaust pipe assemblies (DPF catalytic converter) or the A/F sensor together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.

    2. A204057
      When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

    3. A204058
      A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Engine and ECT / Utility / Learning values save.

    4. A268095
      Press "Next".

    5. A268096
      Press "Next" again to proceed.

    6. A268097
      Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.

    7. A204055
      If the overwrite confirmation screen is displayed, press "Overwrite".

    8. A268098
      When the operation is finished, confirm the date and time of the save operation, and press "Exit".

  3. LEARNING VALUES WRITE
    This procedure uses the GTS to write all of the learned values (injector compensation code, pilot quantity learning value, crank time compensation learning value, catalyst deterioration learning value and A/F sensor learning value) stored in the GTS to the ECM.
    A202034E02

    HINT:

    1. A204063
      A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Engine and ECT / Utility / Learning values write.

    4. A268099
      Press "Next".

    5. A268100
      Press "Next" again to proceed.

    6. A204062
      If the "Error Learning Values Write" screen indicating a problem with the saved value(s) or an absence of saved values is displayed, perform "Learning Values Save" again.

    7. A204064
      Confirm the date and time of the save operation, and then press "Yes".

    8. A268101
      Confirm the contents, and then press "Next".

    9. A268102
      If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.

    10. Clear the DTCs.

  4. A203986E05
    INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

    NOTICE:
    1. When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.
    2. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
    3. When an injector compensation code is input into the ECM, the pilot quantity learning values stored in the ECM are initialized. Also, DTC P062F is stored when the pilot quantity learning values are initialized.

    Text in Illustration 
    *1
    Injector Compensation Code
    *a
    Example

    1. After replacing injector assemblies with new one(s), input injector compensation code(s) of the injector assemblies into the ECM as follows:

      HINT:
      1. Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.
      2. When only one or more injector assemblies are replaced, input the injector compensation code(s), perform pilot quantity learning, and then clear the DTCs.
      3. When the engine switch is turned on (IG) after replacing the ECM, DTC P062F is stored. This indicates that the injector compensation code(s) need to be registered. Manually clear the DTC upon completion of pilot quantity learning.

      1. Input the compensation code(s), which is/are imprinted on the head portion(s) of the new injector assemblies, into the GTS.
      2. Input the new injector compensation code(s) into the ECM using the GTS.
      3. Turn the GTS off and turn the engine switch off.
      4. Wait for at least 30 seconds.
      5. Turn the engine switch on (IG) and turn the GTS on.
      6. Perform pilot quantity learning.
      7. Clear DTC P062F stored in the ECM using the GTS.

        NOTICE:
        If the DTCs are cleared without performing pilot quantity learning, DTC P062F is stored immediately after clearing DTCs.

    2. Register compensation codes.
      A202035E04

      1. Connect the GTS to the DLC3.
      2. Turn the engine switch on (IG).

        NOTICE:
        Do not start the engine.

      3. Turn the GTS on.

      4. A208441
        Enter the following menus: Engine and ECT / Utility / Injector Compensation.
      5. Press Next.

      6. A208442
        Press Next again to proceed.

      7. A204039
        Select "Set Compensation Code".
      8. Press Next.

      9. A204040
        Select the number of the cylinder corresponding to the injector compensation code that you want to register.
      10. Press Next.

      11. A204041
        Register compensation code.
        1. Press Input.

        2. A168951
          Manually input the cylinder compensation code using the keyboard on the GTS screen. The code is a 30-digit, alphanumeric value printed on the injector head portion.

          HINT:
          Each injector compensation code is unique. The compensation code for each selected cylinder must be input into the GTS correctly.

        3. Confirm that the compensation code for the selected cylinder is correct, and then press OK.

      12. A204042
        Check that the compensation code displayed on the screen is correct by comparing it with the 30-digit alphanumeric value on the head portion of the injector assembly.

        NOTICE:
        If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

        HINT:
        1. If a wrong compensation code is input or read, return to the Input Value screen by pressing Input.
        2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

      13. Press Next to register the injector compensation code in the ECM.

        HINT:
        1. If the registration process fails, the injector compensation code may be incorrect. Check the injector compensation code again.
        2. If the input injector compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.


      14. A204043
        If you want to continue with other compensation code registrations, press Next. To finish the registration, press Exit.
      15. Turn the GTS off and turn the engine switch off.
      16. Wait for at least 30 seconds.
      17. Turn the engine switch on (IG), and then turn the GTS on.
      18. Perform pilot quantity learning.
      19. Clear DTC P062F stored in the ECM using the GTS.

        NOTICE:
        If the DTCs are cleared without performing pilot quantity learning, DTC P062F is stored immediately after clearing DTCs.

  5. PILOT QUANTITY LEARNING

    1. "Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.
    2. This procedure uses the GTS to perform "Pilot Quantity Learning".

    3. When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).

      A204080E06

      NOTICE:
      After completing this procedure, clear the DTCs using the GTS.

      HINT:

      1. A204031
        If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning" is canceled, turn the engine switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.
      2. If an error occurs during learning, check the vehicle condition after turning the engine switch off, and then perform learning again.
      3. If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the engine switch off, and then perform learning again.

      4. A204030
        A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Engine and ECT / Utility / Pilot quantity learning.

    5. A204025
      Press "Next".

    6. A204026
      Press "Next" again to proceed.

    7. A227766
      Confirm that the atmospheric pressure screen is displayed.
      1. Confirm the displayed atmospheric pressure.

        Standard:
        Atmosphere Pressure is 87 kPa or more

        NOTICE:
        1. If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".
        2. If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.

      2. If the atmospheric pressure is within the standard range, proceed to the next screen.

    8. A204027
      Confirm the condition of the engine and wait until learning can be performed.
      Essential Conditions for Learning 
      GTS Display
      Standard
      Coolant Temp
      70 to 96°C
      Intake Air
      -2 to 120°C
      Fuel Temperature
      30 to 90°C
      Battery Voltage
      10 V or higher
      Pilot Quantity State (CAT)
      READY

      HINT:
      1. If the values deviate from the standard above, "Pilot Quantity Learning" enters a standby state or is canceled.
      2. When the display indicates that "Pilot Quantity State (CAT)" is prohibited, perform "Pilot Quantity Learning" after performing the "Activate the DPF Rejuvenate (PM)" Active Test using the GTS.
      3. When the essential conditions to perform learning are met, the screen will change automatically.

      NOTICE:
      1. If "Activate the DPF Rejuvenate (PM)" is performed after an injector compensation code is input but before "Pilot Quantity Learning" is performed, DTC P062F is stored and the MIL illuminates due to "Pilot Quantity Learning" being incomplete.
      2. Using the GTS, make sure that DTCs other than DTC P062F are not output.
      3. If DTCs other than DTC P062F are output, perform troubleshooting for those DTCs, and then perform "Activate the DPF Rejuvenate (PM)".

      HINT:
      DTC P062F is stored when the value registered in the ECM for an input injector compensation code, catalyst deterioration learning value and/or pilot quantity deterioration learning value is the initial value.

    9. Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.
      A245205

      HINT:
      1. After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.
      2. It is possible to confirm the status of the learning operation during "Pilot Quantity Learning" by observing the blinking pattern of the glow indicator light.

      Glow Indicator Light Blinking Pattern 
      Learning Status
      Glow Indicator Light Condition
      Conditions essential to start learning have not been met
      Blinking at 0.5 second intervals
      Conditions essential to start learning have been met
      Blinking at 1 second intervals
      During racing (learning is being performed)
      Blinking at 1 second intervals
      Learning is finished
      Off
      Learning has been canceled
      Blinking at 1.5 second intervals
      Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern)
      Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)
      A178592E02
      A178593E02

    10. A204029
      When the screen changes, push "Exit".

    11. Turn the GTS off and turn the engine switch off.

    12. Wait for at least 10 seconds.

    13. Turn the engine switch on (IG), and then turn the GTS on.

    14. Clear the DTCs.

    15. Turn the engine switch off.

      NOTICE:
      Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the engine switch off.

      HINT:
      1. The main relay turns off after the learned value is stored in the ECM.
      2. The main relay turns off within approximately 5 to 10 seconds of turning the engine switch off.

  6. PILOT QUANTITY LEARNING (DETAIL)

    1. "Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.
      It takes time to clear the learned values and perform learning for all cylinders.
    2. This procedure uses the GTS to perform "Pilot Quantity Learning (Detail)".
    3. When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).
    A204080E07

    NOTICE:
    After completing this procedure, clear the DTCs using the GTS.

    HINT:

    1. A206037
      If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning (Detail)" is canceled, turn the engine switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.
    2. If an error occurs during learning, check the vehicle condition after turning the engine switch off, and then perform learning again.
    3. If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the engine switch off, and then perform learning again.

    4. A206036
      A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Engine and ECT / Utility / Pilot quantity learning (Detail).

    5. A206032
      Press "Next".

    6. A206033
      Press "Next" again to proceed.

    7. A227771
      Confirm that the atmospheric pressure screen is displayed.
      1. Confirm the displayed atmospheric pressure.

        Standard:
        Atmosphere Pressure is 87 kPa or more

        NOTICE:
        1. If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".
        2. If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.

      2. If the atmospheric pressure is within the standard range, proceed to the next screen.

    8. A206034
      Confirm the condition of the engine and wait until learning can be performed.
      Essential Conditions for Learning 
      GTS Display
      Standard
      Coolant Temp
      70 to 96°C
      Intake Air
      -2 to 120°C
      Fuel Temperature
      30 to 90°C
      Battery Voltage
      10 V or higher
      Pilot Quantity State (CAT)
      READY

      HINT:
      1. If the values deviate from the standard above, "Pilot Quantity Learning (Detail)" enters a standby state or is canceled.
      2. When the display indicates that "Pilot Quantity State (CAT)" is prohibited, perform "Pilot Quantity Learning" after performing the "Activate the DPF Rejuvenate (PM)" Active Test using the GTS.
      3. When the essential conditions to perform learning are met, the screen will change automatically.

      NOTICE:
      1. If "Activate the DPF Rejuvenate (PM)" is performed after an injector compensation code is input but before "Pilot Quantity Learning" is performed, DTC P062F is stored and the MIL illuminates due to "Pilot Quantity Learning" being incomplete.
      2. Using the GTS, make sure that DTCs other than DTC P062F are not output.
      3. If DTCs other than DTC P062F are output, perform troubleshooting for those DTCs, and then perform "Activate the DPF Rejuvenate (PM)".

      HINT:
      DTC P062F is stored when the value registered in the ECM for an input injector compensation code, catalyst deterioration learning value and/or pilot quantity deterioration learning value is the initial value.

    9. Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.
      A245205

      HINT:
      1. After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.
      2. It is possible to confirm the status of the learning operation during "Pilot Quantity Learning (Detail)" by observing the blinking pattern of the glow indicator light.

      Glow Indicator Light Blinking Pattern 
      Learning Status
      Glow Indicator Light Condition
      Conditions essential to start learning have not been met
      Blinking at 0.5 second intervals
      Conditions essential to start learning have been met
      Blinking at 1 second intervals
      During racing (learning is being performed)
      Blinking at 1 second intervals
      Learning is finished
      Off
      Learning has been canceled
      Blinking at 1.5 second intervals
      Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern)
      Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)
      A178592E02
      A178593E02

    10. A206039
      When the screen changes, push "Exit".

    11. Turn the GTS off and turn the engine switch off.

    12. Wait for at least 10 seconds.

    13. Turn the engine switch on (IG), and then turn the GTS on.

    14. Clear the DTCs.

    15. Turn the engine switch off.

      NOTICE:
      Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the engine switch off.

      HINT:
      1. The main relay turns off after the learned value is stored in the ECM.
      2. The main relay turns off within approximately 5 to 10 seconds of turning the engine switch off.

  7. PILOT QUANTITY LEARNING VALUE CLEAR

    HINT:
    1. If the atmospheric pressure is below the threshold value, "Pilot Quantity Learning" will not be completed and DTC P062F is stored. After "Pilot Quantity Learning Value Clear" is performed, DTC P062F will not be stored.
    2. Clear the learned values using the following procedure.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Enter the following menus: Engine and ECT / Utility / Pilot Quantity Learning Value Clear.

    4. A227767
      Press "Next".

    5. A227768
      Confirm that the atmospheric pressure screen is displayed.
      1. Confirm the displayed atmospheric pressure.

        Standard:
        Atmosphere Pressure is below 87 kPa

        NOTICE:
        1. If the atmospheric pressure is higher than the standard range for performing "Pilot Quantity Learning Value Clear", do not clear the learned values. Instead, perform "Pilot Quantity Learning".
        2. When the atmospheric pressure is higher than the standard range, perform "Pilot Quantity Learning" without initializing the learned values using "Pilot Quantity Learning Value Clear". If the learned values are initialized when the atmospheric pressure is higher than the standard range, the following symptoms may appear. Be sure to correctly follow procedures.
          1. Driveability problems
          2. Rough idle
          3. Emission of white or black smoke, etc.

      2. Proceed to the next screen.

    6. A227769
      Select the cylinders whose learned value will be cleared.

      NOTICE:
      1. Multiple cylinders can be selected.
      2. Only the cylinders for which injector compensation codes have been written must have their learned value cleared.

    7. After selecting the cylinders whose learned value will be cleared, press "Next" to begin the initialization.

    8. A227770
      When the screen changes, push "Exit".

    9. Turn the GTS off and turn the engine switch off.

    10. Wait for at least 10 seconds.

    11. Turn the engine switch on (IG) and turn the GTS on.

    12. Clear the DTCs.

    13. Turn the engine switch off and leave the vehicle for 30 seconds or more.

    14. Turn the engine switch on (IG) for 1 second.

    15. Enter the following menus: Engine and ECT / Trouble Codes.

    16. Read the DTCs.

    17. Confirm that no DTCs are output.

  8. DESCRIPTION OF VIN

    NOTICE:
    The Vehicle Identification Number (VIN) must be input into the replacement ECM.

    HINT:
    The VIN is a 17-digit alphanumeric value. An GTS is required to register the VIN.

    This registration section consists of two parts, Read VIN and Write VIN.
    1. Read VIN: Explains the VIN reading process in a flowchart. This process allows the VIN stored in the ECM to be read, in order to confirm that the two VINs, the VIN provided with the vehicle and the VIN stored in the vehicle's ECM, are the same.
    2. Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.

  9. READ VIN

    1. Confirm the vehicle VIN.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS ON.

    5. Select the following menu items: Engine and ECT / Utility / VIN.
      A148023E01

  10. WRITE VIN

    1. Confirm the vehicle VIN.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS ON.

    5. Select the following menu items: Engine and ECT / Utility / VIN.
      A148024E01
      A148025E01
      A148026E01


INITIALIZATION RELATED TO ECD SYSTEM (w/ DPF)
  1. INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, EGR VALVE ASSEMBLY AND TURBOCHARGER SUB-ASSEMBLY

    HINT:
    When the diesel throttle body assembly, EGR valve assembly or turbocharger sub-assembly is replaced, perform initialization


    1. Turn the engine switch on (IG).

      NOTICE:
      Do not start the engine.

    2. Turn the engine switch off and wait for 30 seconds or more.

    3. Turn the engine switch on (IG) and wait for 10 seconds or more.

  2. CATALYST RECORD OF DPF THERMAL DETERIORATION CLEAR FUNCTION

    HINT:
    When the front exhaust pipe assemblies (DPF catalytic converter) or monolithic converter assemblies (CCo catalytic converter) are replaced, the catalyst record of thermal deterioration stored in the ECM must be cleared.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. A113709
      Enter the menu options in this order: Engine and ECT / Utility / Catalyst Record Clear.

    5. Press "Next".

    6. A113710
      Press "Exit".

  3. SUPPLY PUMP INITIALIZATION PROCEDURE

    HINT:
    After replacing the fuel supply pump assembly and/or ECM:
    1. If the engine is defective or stalls immediately after startup, the learned values of the ECM must be initialized. The engine can be initialized through the GTS or by connecting DLC3 terminals.
    2. If the engine starts normally, initialization is not necessary. Perform the steps labeled procedure "A" and procedure "B" only.


    1. A208443
      Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

      NOTICE:
      Do not start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Engine and ECT / Utility / Supply Pump Initialization.

    5. Press "Next".

    6. A208444
      Press "Next".

    7. A208445
      Press "Exit".

    8. Start the engine to check if the initialization is complete. If the engine cannot be started, repeat the initialization procedures from the beginning (Procedure "A").

    9. Idle the engine for at least 1 minute under the following conditions: (Procedure "B")

      1. The engine coolant temperature is 60°C (140°F) or higher.
      2. The fuel temperature is 20°C (68°F) or higher.

      NOTICE:
      Do not race the engine immediately after starting the engine. After warming up the engine, racing the engine is acceptable.

      HINT:
      1. The engine coolant temperature can be estimated by touching the outlet hose.
      2. The fuel temperature can be estimated by using the ambient temperature as a substitute.
      3. If the engine coolant temperature is difficult to estimate, use the GTS and enter the following menus: Engine and ECT / Data List / Coolant Temp.

    10. Initialization is complete.

  4. CRANK TIME COMPENSATION RESET FUNCTION

    1. This procedure uses the GTS to perform "Crank Time Compensation Reset".
    2. When replacing the timing rotor (engine assembly), perform "Crank Time Compensation Reset".

    HINT:

    1. A204035
      If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.
    2. A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

      NOTICE:
      Do not start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Engine and ECT / Utility / Crank Time Compensation Reset.

    5. A204033
      When the first screen is displayed, check the vehicle condition and push "Next".

    6. A204034
      When the screen indicating reset completion is displayed, push "Exit".

  5. A/F SENSOR COMPENSATION RESET FUNCTION

    1. This procedure uses the GTS to perform "A/F Sensor Compensation Reset".
    2. When replacing the A/F sensor, replace the sensor and then perform "A/F Sensor Compensation Reset".

    HINT:

    1. A204038
      If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.
    2. A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

      NOTICE:
      Do not start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Engine and ECT / Utility / A/F Sensor Compensation Reset.

    5. A204036
      When the first screen is displayed, check the vehicle condition and push "Next".

    6. A204037
      When the screen indicating reset completion is displayed, push "Exit".


REGISTRATION RELATED TO ECD SYSTEM (w/o DPF)

  1. A141119E02
    REGISTRATION

    NOTICE:
    1. When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.
    2. Fuel injector compensation codes are unique, 30 digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


    1. After replacing fuel injector(s) with new one(s), input compensation code(s) of fuel injector(s) into ECM as follows:

      HINT:
      1. Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each fuel injector.
      2. When you first turn the ignition switch to ON after replacing the ECM or a fuel injector(s), DTC P1601 is set. This is to inform you that registration of a fuel injector compensation code(s) is/are required. Manually clear the DTC upon completion of the compensation code registration.

      1. Input the compensation code(s), which is/are imprinted on the head portion(s) of the new fuel injector(s), into the intelligent tester.
      2. Input the new compensation code(s) into the ECM using the tester.
      3. Turn the tester off and turn the ignition switch off.
      4. Wait for at least 30 seconds.
      5. Turn the ignition switch to ON and turn the tester on.
      6. Clear DTC P1601 stored in the ECM using the tester.

    2. Register compensation code.
      A169590E04

      1. Connect the intelligent tester to the DLC3.
      2. Turn the ignition switch to ON .

        NOTICE:
        Do not start the engine.

      3. Turn the tester on.

      4. G036522E01
        Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.
      5. Press Next.

      6. G036523E01
        Press Next again to proceed.

      7. G036528E01
        Select "Set Compensation Code".
      8. Press Next.

      9. A166685
        Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.
      10. Press Next.

      11. G036529E01
        Register compensation code.
        1. Press Input.

        2. A168951
          Manually input the cylinder compensation code using the keyboard on the tester screen. The code is a 30 digit, alphanumeric value printed on the injector head portion.

          HINT:
          Each fuel injector compensation code is unique. The compensation code for each selected cylinder must be input into the tester correctly.

        3. Confirm that the compensation code for the selected cylinder is correct, and then press OK.

      12. G036531E01
        Check that the compensation code displayed on the screen is correct by comparing it with the 30 digit alphanumeric value on the head portion of the fuel injector.

        NOTICE:
        If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

        HINT:
        1. If a wrong compensation code is input or read, return to the Input Value screen by pressing Input.
        2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

      13. Press Next to register the compensation code in the ECM.

        HINT:
        1. If the registration process fails, the compensation code may be incorrect. Check the compensation code again.
        2. If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.


      14. G036532E01
        If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.
      15. Turn the ignition switch off and then turn the tester off.
      16. Wait for at least 30 seconds.
      17. Turn the ignition switch to ON and then turn the tester on.
      18. Clear DTC P1601 stored in the ECM using the tester.

  2. READING REGISTERED DATA

    NOTICE:
    1. When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is changed, all of the existing fuel injector compensation codes must be input into the new ECM.
    2. Fuel injector compensation codes are unique, 30 digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


    1. When replacing ECM with a new one, input all fuel injector compensation codes into new ECM as follows:

      HINT:
      1. Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector.
      2. When you first turn the ignition switch to ON after replacing the ECM or a fuel injector(s), DTC P1601 is set. This is to inform you that registration of a fuel injector compensation codes(s) is/are required. Manually clear the DTC upon completion of the compensation code registration.

      1. Prior to replacing the ECM, read and save each fuel injector compensation code, stored in the original ECM, using the intelligent tester.
      2. After installing a new ECM, input the saved compensation codes into the new ECM using the tester.
      3. Turn the tester off and turn the ignition switch off.
      4. Wait for at least 30 seconds.
      5. Turn the ignition switch to ON and turn the tester on.
      6. Clear DTC P1601 stored in the ECM using the tester.

    2. Read and save fuel injector compensation codes.
      A169591E02

      HINT:
      The following operation is available with ECMs that can transmit the registered fuel injector compensation codes to the intelligent tester.


      1. A141119E02
        Connect the intelligent tester to the DLC3.
      2. Turn the ignition switch to ON.

        NOTICE:
        Do not start the engine.

      3. Turn the tester on.

      4. G036522E01
        Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.
      5. Press Next.

      6. G036523E01
        Press Next again to proceed.

      7. G036524E01
        Select Read Compensation Code.
      8. Press Next.

      9. A166685
        Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.
      10. Press Next.

        HINT:
        The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and restart this operation.


      11. G036526E01
        Check the fuel injector compensation code (30 digit alphanumeric value) displayed on the tester screen.
      12. Press Save.

      13. A108923E05
        Check that the compensation code displayed on the tester screen is correct.
      14. Press Save or Replace to save the fuel injector compensation code.

        HINT:
        1. The existing compensation code is overwritten with the new compensation code and is deleted from the tester.
        2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.


      15. G036526E01
        If you want to read and save other fuel injector compensation codes for other cylinders, press Next to continue. To finish this operation, press Cancel.
      16. Turn the ignition switch off.
      17. Turn the tester off.
      18. Replace the ECM.

      19. A141119E02
        Connect the intelligent tester to the DLC3.
      20. Turn the ignition switch to ON.

        NOTICE:
        Do not start the engine.

      21. Turn the tester on.

      22. G036522E01
        Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.
      23. Press Next.

      24. G036523E01
        Press Next again to proceed.

      25. G036528E01
        Select Set Compensation Code.
      26. Press Next.

      27. A166685
        Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.
      28. Press Next.

      29. G036531E01
        Check that the compensation code displayed on the screen is correct by comparing it with the 30 digit alphanumeric value on the head portion of the fuel injector.

        NOTICE:
        If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

        HINT:
        1. If a wrong compensation code is input or read, return to the Input Value screen by pressing input.
        2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

      30. Press Next to register the compensation code in the ECM.

        HINT:
        1. If the registration process fails, the compensation code may be incorrect. Check the compensation code again.
        2. If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.


      31. G036532E01
        If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.
      32. Turn the ignition switch off and then turn the tester off.
      33. Wait for at least 30 seconds.
      34. Turn the ignition switch to ON and then turn the tester on.
      35. Clear DTC P1601 stored in the ECM using the tester.


INITIALIZATION RELATED TO ECD SYSTEM (w/o DPF)

  1. A141744E01
    FUEL SUPPLY PUMP INITIALIZATION PROCEDURE

    HINT:
    After replacing the supply pump and/or the ECM, the ECM learned values must be initialized.
    The engine can be initialized through the intelligent tester or by connecting DLC3 terminals.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine / Utility / Supply Pump Initialization.

    5. Press "Next".

    6. A141745E01
      Press "Next".

    7. A141746E01
      Press "Exit".

    8. Start the engine to check if the initialization is complete. If the engine cannot be started, repeat the initialization procedures from the beginning.

    9. Idle the engine for at least 1 minute under the following conditions:

      1. The engine coolant temperature is 60°C (140°F) or more.
      2. The fuel temperature is 20°C (68°F) or more.

      NOTICE:
      Do not race the engine immediately after starting the engine. After warming up the engine, racing the engine is acceptable.

      HINT:
      If the engine coolant temperature is difficult to estimate, use the intelligent tester and enter the following menus: Powertrain / Engine / Data List / Coolant Temp and Fuel Temperature.

    10. Initialization is complete.


INITIALIZATION RELATED TO DYNAMIC RADAR CRUISE CONTROL

NOTICE:
After removing and installing or replacing the distance control ECU, be sure to perform the following procedures.

  1. Turn the engine switch on (IG).

  2. Turn the cruise control main switch on.

  3. Depress the brake pedal (brake switch on).

  4. With the brake pedal depressed, push the cruise control main switch to +RES 3 times within 3 seconds, and check that the buzzer sounds.

    NOTICE:
    At this time, do not turn the headlight dimmer switch on. Due to the activation of the beam axis automatic adjustment mode, turning the headlight dimmer switch on may result in an incorrect setting. If the headlight dimmer switch is turned on by mistake, perform the beam axis adjustment again.


ADJUSTMENT FOR MILLIMETER WAVE RADAR SENSOR

  1. E162201E04
    ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

    NOTICE:
    1. Perform measurements on a level surface.
    2. Make sure that there are no metal objects on the ground or within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.

    Text in Illustration 
    *1
    Approx. 10 m
    *2
    Approx. 14 m

    1. Before adjusting, perform the following:

      1. Remove all cargo from the inside of the vehicle.
      2. Adjust the tire pressure to the specified value(s).

    2. w/ Air suspension:
      Adjust the vehicle's height to the standard height.

    3. Adjust the vertical direction.

      1. Remove any dust and oil from the level rack of the millimeter wave radar sensor assembly.

      2. E239955E01
        Set a level for use with the sensor in the center of the level rack of the millimeter wave radar sensor assembly.
        Text in Illustration 
        *1
        Level

      3. E239956E01
        Using a screwdriver, adjust the sensor by turning the vertical adjusting bolt of the millimeter wave radar sensor assembly (bolt A) until the air bubble is centered on the red line of the level as shown in the illustration.

        Standard:
        0.2° upward

        HINT:
        The adjustable range within the red frame of the level is +/-0.2°.

        Adjustment: 
        Vertical adjustment
        1. Upward direction: Turn bolt A in minus direction
        2. Downward direction: Turn bolt A in plus direction
        For 1 complete turn of screwdriver, sensor moves about 0.12°
        Text in Illustration 
        *1
        Level
        *2
        Air Bubble
        *3
        Bolt A
        *a
        FR
        *b
        LH
        *c
        Screwdriver Insertion Hole

    4. E239957E01
      Adjust SST (reflector) height.
      SST
      09870-60000   (09870-60010)
      09870-60040  
      1. Adjust SST (reflector) so that the center of SST (reflector) is the same height as the millimeter wave radar sensor assembly.
        Text in Illustration 
        *1
        Millimeter Wave Radar Sensor

    5. Place SST (reflector).

      1. Hang a pointed weight from the center of the front and rear bumpers of the vehicle (center of the emblem) and accurately mark the center points on the ground.

      2. E162203E04
        Mark a point 5 m (16.4 ft.) in front of the vehicle on the line that connects the front and rear center point marks.

        HINT:
        Affix one end of a string to the rear center point mark and extend the string 5 m (16.4 ft.) from the front of the vehicle. Move the other end of the string left and right to align the string with the front center point mark and make a straight line.

        Text in Illustration 
        *1
        String
        *a
        Adjust Center By Moving String To Right And Left
        *b
        Extend String Through Front Center Mark

      3. Place SST at a position 12 mm (0.472 in.) from the marked position, to the right of the vehicle.

        NOTICE:
        Perform the operation as precisely as possible.


        E239958E01
        Text in Illustration 
        *a
        Reflector (SST) Placement Point
        *b
        Millimeter Wave Radar Sensor Position

    6. Adjust the beam axis.

      1. Connect the intelligent tester to the DLC3.
      2. Turn the engine switch on (IG).
      3. Turn the intelligent tester main switch ON, and turn the cruise control main switch ON.
      4. Select "Radar Cruise" from the display screen.

        HINT:
        A buzzer will sound for 1 second.

      5. Select "Utility" from the display screen.
      6. Select "Beam Axis Adjustment" from the display screen.
      7. Follow the tester display, and continue with the adjustment.
      8. Intelligent tester

        NOTICE:
        1. Turn the cruise control main switch ON before pressing Next.
        2. Make sure there is at least 20 cm (7.9 inches) between the radar sensor and any nearby individuals.

      9. Check the following items on the laser cruise divergence data screen.

        CAUTION:
        While using the intelligent tester's beam axis adjustment mode, the actual direction and angle of the radar sensor may be different from the intelligent tester's data. In such a case, the deviation is displayed on the combination meter's multi-information display.

        1. Confirm that the distance value is approximately 5 m (16.41 ft.).

          HINT:
          1. A value between 0.0 and 6.3 m (20.67 ft.) is indicated.
          2. If the distance is 0 m (0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).

        2. Confirm that the left/right side value is between 0.0 and 6.3.

          HINT:
          If the distance is 0 m (0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).

    7. Adjust the horizontal direction.

      1. Read the current amount of angle deviation.

        Standard:
        0° (Both left and right)


      2. E239959E01
        Based on the results of the beam axis deviation measurement, using a screwdriver, adjust the sensor by turning the horizontal adjusting bolt of the millimeter wave radar sensor assembly (bolt B).
        Adjustment: 
        Horizontal adjustment
        Right direction: Turn bolt B in plus direction
        Left direction: Turn bolt B in minus direction
        For 1 complete turn of screwdriver, sensor moves about 0.07°

        NOTICE:
        If it is difficult to reach a value of 0°, it is possible that the sensor is targeting an object other than SST. Reconfirm that there are no reflective objects in the surrounding area.

        Text in Illustration 
        *1
        Bolt B
        *a
        Screwdriver Insertion Hole

      3. E239952E01
        Because the driving learned value will be reset, cover the left half of the sensor with aluminum foil or equivalent (a metal material that blocks electric waves) for a period of approximately 10 seconds.

        NOTICE:
        At this time, leave SST in place and make sure there are no objects between the right half of the sensor and the reflector.

        HINT:
        When the value is reset, the buzzer will sound for 10 seconds, a distance value between 0 and 6.3° and a right side value between 0 and 6.3 m (20.7 ft.) will be displayed on the screen.

        Text in Illustration 
        *1
        Aluminum foil
      4. Continue the procedure according to the display to complete the beam axis adjustment.
      5. Disconnect the intelligent tester from the vehicle.

    8. Reconfirm the vertical direction.


      1. E239955E01
        Set a level for use with the sensor in the center of the level rack of the millimeter wave radar sensor assembly.
        Text in Illustration 
        *1
        Level

      2. E239956E01
        Using a screwdriver, adjust the sensor by turning the vertical adjusting bolt of the millimeter wave radar sensor assembly (bolt A) until the air bubble is centered on the red line of the level as shown in the illustration.

        Standard:
        0.2° upward

        HINT:
        The adjustable range within the red frame of the level is +/-0.2°.

        Adjustment: 
        Vertical adjustment
        1. Upward direction: Turn bolt A in minus direction
        2. Downward direction: Turn bolt A in plus direction
        For 1 complete turn of screwdriver, sensor moves about 0.12°
        Text in Illustration 
        *1
        Level
        *2
        Air Bubble
        *3
        Bolt A
        *a
        FR
        *b
        LH
        *c
        Screwdriver Insertion Hole

  2. DRIVE TEST

    1. Perform the drive test.

      NOTICE:
      1. Be sure to perform the driving test after adjusting the millimeter wave radar sensor assembly.
      2. Be careful when driving.

      1. Drive at 30 km/h (19 mph) on a straight road with good visibility while staying in the center of the lane.

        NOTICE:
        Because the pre-crash safety system may activate under the following conditions, avoid conditions like these when performing the test.
        1. There are objects on the side of the road at the beginning of a curve.
        2. Passing an oncoming vehicle on a curve.
        3. Crossing a narrow metal bridge.
        4. There are metal objects on the road surface.
        5. There is an oncoming vehicle when turning right.
        6. Rapidly approaching a vehicle driving in front.

      2. On a straight road, when passing an oncoming vehicle with no danger of collision, check that the master warning does not illuminate and that the buzzer does not sound. At the same time, check that "BRAKE!" is not displayed on the display in the combination meter.
      3. If "BRAKE!" is displayed, perform the millimeter wave radar sensor assembly adjustment again.

        HINT:
        1. Check the installation condition of the millimeter wave radar sensor assembly.
        2. Check that the pre-crash safety brake switch is not pushed in.


INITIALIZATION RELATED TO AUTOMATIC TRANSMISSION SYSTEM (for A750F, 1GR-FE)
  1. RESET MEMORY

    NOTICE:
    1. Perform the Reset Memory (AT initialization) when replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves.
    2. The Reset Memory can be performed only with the intelligent tester.

    HINT:
    The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly. Therefore, when the automatic transmission assembly, valve body assembly or any of the shift solenoid valves has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

      NOTICE:
      After performing the Reset Memory, be sure to perform the Road Test described earlier.

      HINT:
      The ECM learns through the road test.


INITIALIZATION RELATED TO AUTOMATIC TRANSMISSION SYSTEM (for AB60F, 1UR-FE)
  1. RESET MEMORY

    NOTICE:
    1. Perform Reset Memory (AT initialization) when replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves.
    2. Reset Memory can be performed only with the GTS.

    HINT:
    The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly. Therefore, when the automatic transmission assembly, valve body assembly or any of the shift solenoid valves has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.
    The reset procedure is as follows.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

      NOTICE:
      After performing Reset Memory, be sure to perform the Road Test described earlier.

      HINT:
      The ECM learns through the Road Test.


INITIALIZATION RELATED TO AUTOMATIC TRANSMISSION SYSTEM (for AB60F, 3UR-FE)
  1. RESET MEMORY

    NOTICE:
    1. Perform Reset Memory (AT initialization) when replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves.
    2. Reset Memory can be performed only with the intelligent tester.

    HINT:
    The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly. Therefore, when the automatic transmission assembly, valve body assembly or any of the shift solenoid valves has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.
    The reset procedure is as follows.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

      NOTICE:
      After performing Reset Memory, be sure to perform the Road Test described earlier.

      HINT:
      The ECM learns through the Road Test.


INITIALIZATION RELATED TO AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV, AB60F)
  1. RESET MEMORY

    NOTICE:
    1. Perform the Reset Memory (AT initialization) when replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves.
    2. The Reset Memory can be performed only with the intelligent tester.

    HINT:
    The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly. Therefore, when the automatic transmission assembly, valve body assembly or any of the shift solenoid valves has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECT / Utility / Reset Memory.

      NOTICE:
      After performing the Reset Memory, be sure to perform the Road Test described earlier.

      HINT:
      The ECM learns through the Road Test.


INITIALIZATION RELATED TO AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV with DPF, AB60F)
  1. RESET MEMORY

    NOTICE:
    1. Perform the Reset Memory (AT initialization) when replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves.
    2. The Reset Memory can be performed only with the GTS.

    HINT:
    The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly. Therefore, when the automatic transmission assembly, valve body assembly or any of the shift solenoid valves has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

      NOTICE:
      After performing the Reset Memory, be sure to perform the Road Test described earlier.

      HINT:
      The ECM learns through the Road Test.


ADJUSTMENT FOR AUTOMATIC TRANSMISSION FLUID (A750F)

  1. C157019E01
    BEFORE FILLING TRANSMISSION
    1. This transmission requires Toyota Genuine ATF WS transmission fluid.
    2. After servicing the transmission, you must refill the transmission with the correct amount of fluid.
    3. Keep the vehicle level while adjusting the fluid level.
    4. Proceed to the "Transmission Pan Fill" procedures if you replaced the entire transmission, transmission pan, drain plug, valve body and/or torque converter.
    5. Proceed to the ''Transmission Fill'' procedures after removing the refill plug if you replaced the transmission hose and/or output shaft oil seal.

  2. C113723E01
    TRANSMISSION PAN FILL

    1. Remove the refill plug and overflow plug.

    2. Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.

    3. Reinstall the overflow plug.

  3. TRANSMISSION FILL

    1. C158377
      w/o Air Cooled Transmission Oil Cooler (w/ ATF Warmer):
      Push the shaft of the thermostat and fix it in place.
      1. By using compressed air, etc., blow dust off of the thermostat cap to clean it.

      2. C163089E01
        Using a screwdriver, push the shaft of the thermostat.

        HINT:
        1. Pushed amount: 5.5 to 7.0 mm (0.217 to 0.276 in.)
        2. Push the shaft until the screwdriver contacts the inside step of the cap.

      3. With the shaft of the thermostat pressed, push a pin (diameter: 1.0 to 1.8 mm (0.0394 to 0.0709 in.)) into a hole on the side of the thermostat cap. Insert the pin until it passes through the hole on the other side of the thermostat cap to fix the shaft in place.

    2. Fill the transmission with the amount of fluid listed in the table below.

      Standard Capacity:
      Repair
      Fill Amount
      Transmission pan and drain plug removal
      1.7 liters (1.8 US qts, 1.5 Imp. qts)
      Transmission valve body removal
      4.3 liters (4.5 US qts, 3.8 Imp. qts)
      Torque converter removal
      5.4 liters (5.7 US qts, 4.8 Imp. qts)

    3. Reinstall the refill plug to prevent the fluid from splashing.

      HINT:
      If you cannot add the listed amount of fluid, do the following:

      1. Install the refill plug.
      2. Allow the engine to idle with the air conditioning off.
      3. Move the shift lever through the entire gear range to circulate fluid.
      4. Wait for 30 seconds with the engine idling.
      5. Stop the engine.
      6. Remove the refill plug and add fluid.
      7. Reinstall the refill plug.

  4. ADJUST FLUID TEMPERATURE

    NOTICE:
    The fluid temperature can be confirmed by checking the indicator light in the meter or by using the GTS. When using the GTS, it is necessary to change to temperature detection mode in order to idle the vehicle appropriately.


    1. When using the GTS:

      1. Turn the engine switch off.
      2. Connect the GTS to the DLC3.
      3. Turn the engine switch on (IG).
      4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
      5. Enter the following menus: Powertrain / ECT / Data List / A/T Oil Temperature 1.
      6. Check the ATF temperature.

        NOTICE:
        1. The ATF temperature must be between 38 to 45°C (100 to 113°F).
        2. If the ATF temperature is not between 38 to 45°C (100 to 113°F), turn the ignition switch off and wait until the fluid temperature drops between 38 to 45°C (100 to 113°F).

      7. According to the display on the GTS, perform the Active Test "Connect the TC and TE1".

        HINT:
        Indicator lights of the meter blink to output Trouble Codes when TC and TE1 are connected.

      8. Start the engine.

        NOTICE:
        Check that electrical systems such as the air conditioning system, audio system and lighting system are off.

    2. H102392E90
      When not using the GTS:
      SST
      09843-18040  
      1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      2. Start the engine.

        NOTICE:
        Check that electrical systems such as the air conditioning system, audio system and lighting system are off.

        HINT:
        Indicator lights of the meter blink to output Trouble Codes when terminals TC and CG are connected.

    3. Slowly move the shift lever from P to S, then change the gears from 1st to 6th. Then return the shift lever to P.

      HINT:
      Slowly move the shift lever to circulate the fluid through each part of the transmission.

    4. C172430E01
      Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

      Standard condition:
      Indicator light (D) remains illuminated for 2 seconds and then turns off.

    5. When using the GTS:

      1. Return the shift lever to P and press OFF on the Active Test display.

    6. When not using the GTS:

      1. Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).

    7. Allow the engine to idle until the fluid temperature reaches 38 to 45°C (100 to 113°F).

    8. The indicator (D) will come on again when the fluid temperature reaches 38°C (100°F) and will blink when it exceeds 46°C (113°F).

      Indicator Indication of ATF Temperature:
      Below Proper Temperature
      Proper Temperature
      Higher than Proper Temperature
      Data List [A/T Oil Temperature 1]
      38°C (100°F) or less
      Data List [A/T Oil Temperature 1]
      38 to 45°C (100 to 113°F)
      Data List [A/T Oil Temperature 1]
      45°C (113°F) or higher
      Indicator light (D)
      Turns off
      Indicator light (D)
      Turns on
      Indicator light (D)
      Blinking

      NOTICE:
      Perform the fluid level inspection while the indicator light is on.

  5. FLUID LEVEL CHECK

    NOTICE:
    The fluid temperature must be between 38 to 45°C (100 to 113°F) to accurately check the fluid level.


    1. C113723E01
      Remove the overflow plug with the engine idling.

    2. Check that fluid comes out of the overflow tube.
      If fluid does not come out, proceed to the "Transmission Refill" procedures.
      If fluid comes out, wait until the overflow slows to a trickle and proceed to the "Complete" procedures.

  6. TRANSMISSION REFILL

    1. Remove the overflow plug.

    2. Remove the refill plug.

    3. Add ATF into the refill hole until ATF flows from the overflow tube.

    4. Wait until the overflow slows to a trickle and proceed to the ''COMPLETE'' procedures.

  7. COMPLETE

    1. Install a new gasket and the overflow plug.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Stop the engine.

    3. Install a new gasket and the refill plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    4. C161813E01
      w/o Air Cooled Transmission Oil Cooler (w/ ATF Warmer):
      1. Remove the pin.

        NOTICE:
        1. Make sure the shaft of the thermostat is protruding from the hole of the cap.
        2. Check that there is no ATF leaking from the cap hole.


ADJUSTMENT FOR AUTOMATIC TRANSMISSION FLUID (AB60F)

NOTICE:
  1. This transmission requires Toyota Genuine ATF WS.
  2. After servicing the transmission, you must follow the ATF adjustment procedure.
  3. Maintain the vehicle in a horizontal position while adjusting the fluid level.

  1. PRELIMINARY PROCEDURES (w/ ATF Warmer)

    1. Using compressed air or equivalent, blow dust off the thermostat cap to clean it.

    2. C193546E02
      Using a screwdriver, push in the shaft of the thermostat.
      Text in Illustration 
      *1
      Screwdriver
      *2
      Cap
      *3
      Shaf
      *4
      Step
      *5
      Pin

      HINT:
      1. Pushed amount: 5.5 to 7.0 mm (0.217 to 0.276 in.)
      2. Push in the shaft until the screwdriver contacts the step inside the cap.

    3. With the shaft of the thermostat pressed, insert a pin into a hole on the side of the thermostat cap. Insert the pin until it passes through the hole on the other side of the thermostat cap to fix the shaft in place.

      HINT:
      Pin diameter: 1.0 to 1.8 mm (0.0394 to 0.0709 in.)

  2. C175571E02
    BEFORE FILLING TRANSMISSION
    1. This transmission requires Toyota Genuine ATF WS transmission fluid.
    2. After servicing the transmission, you must refill the transmission with the correct amount of fluid.
    3. Keep the vehicle level while adjusting the fluid level.
    4. Proceed to the "Transmission Pan Fill" procedures if you replaced the entire transmission, transmission pan, drain plug, valve body and/or torque converter.
    5. Proceed to the "Transmission Fill" procedures after removing the refill plug if you replaced the transmission hose and/or output shaft oil seal.
      Text in Illustration 
      *1
      Refill Plug
      *2
      Refill Hole
      *3
      Overflow Plug

  3. C161094E03
    TRANSMISSION PAN FILL

    1. Remove the refill plug and overflow plug.

    2. Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.

    3. Reinstall the overflow plug.

      Text in Illustration 
      *1
      Overflow Tube
      *a
      Specified Fluid Level

  4. TRANSMISSION FILL

    1. Fill the transmission with the amount of fluid listed in the table below.

      Standard Capacity:
      Repair
      Fill Amount
      Transmission pan and drain plug removal
      2.1 liters (2.2 US qts, 1.9 Imp. qts)
      Transmission valve body removal
      4.7 liters (5.0 US qts, 4.1 Imp. qts)
      Torque converter removal
      6.1 liters (6.4 US qts, 5.4 Imp. qts)

      Standard Capacity:
      Repair
      Fill Amount
      Transmission pan and drain plug removal
      2.1 liters (2.2 US qts, 1.9 Imp. qts)
      Transmission valve body removal
      4.7 liters (5.0 US qts, 4.1 Imp. qts)
      Torque converter removal
      6.1 liters (6.4 US qts, 5.4 Imp. qts)

    2. Reinstall the refill plug to prevent the fluid from splashing.

      HINT:
      If you cannot add the listed amount of fluid, do the following:

      1. Install the refill plug.
      2. Allow the engine to idle with the air conditioning OFF.
      3. Move the shift lever through the entire gear range to circulate fluid.
      4. Wait for 30 seconds with the engine idling.
      5. Stop the engine.
      6. Remove the refill plug and add fluid.
      7. Reinstall the refill plug.

  5. ADJUST FLUID TEMPERATURE

    NOTICE:
    The fluid temperature can be confirmed by checking the indicator light in the meter or by using the intelligent tester. When using the intelligent tester, it is necessary to change to temperature detection mode in order to idle the vehicle appropriately.


    1. When using the intelligent tester:

      1. Turn the ignition switch off.
      2. Connect the intelligent tester to the DLC3.
      3. Turn the ignition switch to ON.
      4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
      5. Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.
      6. for 1VD-FTV:
        Check the ATF temperature.

        NOTICE:
        1. The ATF temperature must be between 41 to 46°C (106 to 115°F).
        2. If the ATF temperature is not between 41 to 46°C (106 to 115°F), turn the ignition switch off and wait until the fluid temperature drops between 41 to 46°C (106 to 115°F).

      7. for 3UR-FE, 1UR-FE:
        Check the ATF temperature.

        NOTICE:
        1. The ATF temperature must be between 43 to 48°C (109 to 118°F).
        2. If the ATF temperature is not between 43 to 48°C (109 to 118°F), turn the ignition switch off and wait until the fluid temperature drops between 43 to 48°C (109 to 118°F).

      8. for 1VD-FTV:
        According to the display on the intelligent tester, perform the Active Test "Connect the TC and TE1".
      9. for UR Engine Series:
        According to the display on the intelligent tester, perform the Active Test "Connect the TC and TE1".

        HINT:
        Indicator lights of the combination meter blink to output DTCs when TC and TE1 are connected.

      10. Start the engine.

        NOTICE:
        Check that electrical systems such as the air conditioning system, audio system and lighting system are off.

    2. C101492E10
      When not using the intelligent tester:
      SST
      09843-18040  
      1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
        Text in Illustration 
        *A
        Front View of DLC3
      2. Start the engine.

        NOTICE:
        Check that electrical systems such as the air conditioning system, audio system and lighting system are off.

        HINT:
        Indicator lights of the meter blink to output DTCs when terminals TC and CG are connected.

    3. Slowly move the shift lever from P to S, then change the gears from 1st to 6th. Then return the shift lever to P.

      HINT:
      Slowly move the shift lever to circulate the fluid through each part of the transmission.

    4. C172430E02
      Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

      Standard condition:
      Indicator light (D) remains illuminated for 2 seconds and then turns off.

      Text in Illustration 
      *A
      w/ Multi-information Display
      *B
      w/o Multi-information Display

      Standard condition:
      Indicator light (D) remains illuminated for 2 seconds and then turns off.

    5. When using the intelligent tester:

      1. Return the shift lever to P and press OFF on the Active Test display.

    6. When not using the intelligent tester:

      1. Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).

    7. for 1VD-FTV:
      Allow the engine to idle until the fluid temperature reaches 41 to 46°C (106 to 115°F).

    8. for 3UR-FE, 1UR-FE:
      Allow the engine to idle until the fluid temperature reaches 43 to 48°C (109 to 118°F).

    9. for 1VD-FTV:
      The indicator (D) will come on again when the fluid temperature reaches 41°C (106°F) and will blink when it exceeds 46°C (115°F).

      Indicator Indication of ATF Temperature :
      Below Proper Temperature
      Proper Temperature
      Higher than Proper Temperature
      Data List [A/T Oil Temperature 1]
      41°C (106°F) or less
      Data List [A/T Oil Temperature 1]
      41 to 46°C (106 to 115°F)
      Data List [A/T Oil Temperature 1]
      46°C (115°F) or higher
      Indicator light (D)
      Turns off
      Indicator light (D)
      Turns on
      Indicator light (D)
      Blinking

      NOTICE:
      Perform the fluid level inspection while the indicator light is on.

    10. for 3UR-FE, 1UR-FE:
      The indicator (D) will come on again when the fluid temperature reaches 43°C (109°F) and will blink when it exceeds 48°C (118°F).

      Indicator Indication of ATF Temperature :
      Below Proper Temperature
      Proper Temperature
      Higher than Proper Temperature
      Data List [A/T Oil Temperature 1]
      43°C (109°F) or less
      Data List [A/T Oil Temperature 1]
      43 to 48°C (109 to 118°F)
      Data List [A/T Oil Temperature 1]
      48°C (118°F) or higher
      Indicator light (D)
      Turns off
      Indicator light (D)
      Turns on
      Indicator light (D)
      Blinking

      NOTICE:
      Perform the fluid level inspection while the indicator light is on.

  6. FLUID LEVEL CHECK

    NOTICE:
    1. for 1VD-FTV:
      The fluid temperature must be between 41 and 46°C (106 and 115°F) to accurately check the fluid level.
    2. for 3UR-FE, 1UR-FE:
      The fluid temperature must be between 43 and 48°C (109 and 118°F) to accurately check the fluid level.


    1. C161094E03
      Remove the overflow plug with the engine idling.

    2. Check that fluid comes out of the overflow tube.
      If fluid does not come out, proceed to the "Transmission Refill" procedures.
      If fluid comes out, wait until the overflow slows to a trickle and proceed to the "Complete" procedures.

      Text in Illustration 
      *1
      Overflow Tube
      *a
      Specified Fluid Level

  7. TRANSMISSION REFILL

    1. Remove the overflow plug.

    2. Remove the refill plug and gasket.

    3. Add ATF into the refill hole until ATF flows from the overflow tube.

    4. Wait until the overflow slows to a trickle and proceed to the "Complete" procedures.

  8. COMPLETE

    1. Install a new gasket and the overflow plug.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Stop the engine.

    3. Install a new gasket and the refill plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }


ADJUSTMENT FOR PARK/NEUTRAL POSITION SWITCH (for AUTOMATIC TRANSMISSION)

  1. D025795E10
    ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY

    1. Loosen the bolt of the park/neutral position switch and move the shift lever to N.

    2. Align the groove with the neutral basic line.

    3. Hold the switch in the position described above and tighten the bolt.

      Torque:
      13 N*m{ 130 kgf*cm , 10 ft.*lbf }

    4. After the adjustment, perform the on-vehicle inspection.


ADJUSTMENT FOR CLUTCH (for LHD)

  1. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

    1. C173250E01
      Check that the clutch pedal height is correct.

      Standard Clutch Pedal Height from Tibia Pad:
      162.7 to 172.7 mm (6.41 to 6.79 in.)

    2. Adjust the clutch pedal height.

      1. Loosen the lock nut and turn the stopper bolt or clutch switch until the height is correct. Tighten the lock nut.

      Torque:
      16 N*m{ 160 kgf*cm , 12 ft.*lbf }

    3. D031462E03
      Check that the clutch pedal free play and push rod play are correct.
      1. Depress the clutch pedal until the clutch resistance begins to be felt.

        Standard Pedal Free Play:
        5.0 to 15.0 mm (0.197 to 0.591 in.)

      2. Gently depress the clutch pedal until the resistance begins to increase a little.

        Standard Push Rod Play at Pedal Top:
        1.0 to 5.0 mm (0.0394 to 0.197 in.)

    4. Adjust the clutch pedal free play and push rod play.

      1. Loosen the lock nut and turn the clutch push rod until the clutch pedal free play and push rod play are correct.
      2. Tighten the lock nut.
      3. After adjusting the clutch pedal free play and push rod play, check the clutch pedal height.

        Standard Clutch Pedal Height from Tibia Pad:
        162.7 to 172.7 mm (6.41 to 6.79 in.)

      Torque:
      12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    5. CL00512E17
      Check the clutch release point.
      1. Pull the parking brake lever and chock the wheels.
      2. Start the engine and allow it to idle.
      3. Without depressing the clutch pedal, slowly move the shift lever to R until the gears engage.
      4. Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

        Standard Distance from Pedal Stroke End Position to Release Point:
        20 mm (0.787 in.) or more

        If the distance is not as specified, perform the following operations:
        1. Check the clutch pedal height.
        2. Check the push rod play and pedal free play.
        3. Bleed the clutch line.
        4. Check the clutch cover and disc.


ADJUSTMENT FOR CLUTCH (for RHD)

  1. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

    1. C173230E01
      Check that the clutch pedal height is correct.

      Standard Clutch Pedal Height from Tibia Pad:
      164.8 to 174.8 mm (6.49 to 6.88 in.)

    2. Adjust the clutch pedal height.

      1. Loosen the lock nut and turn the stopper bolt or clutch switch until the height is correct. Tighten the lock nut.

      Torque:
      16 N*m{ 160 kgf*cm , 12 ft.*lbf }

    3. D031462E03
      Check that the clutch pedal free play and push rod play are correct.
      1. Depress the clutch pedal until the clutch resistance begins to be felt.

        Standard Clutch Pedal Free Play:
        5.0 to 15.0 mm (0.197 to 0.591 in.)

      2. Gently depress the clutch pedal until the resistance begins to increase a little.

        Standard Push Rod Play at Pedal Top:
        1.0 to 5.0 mm (0.0394 to 0.197 in.)

    4. Adjust the clutch pedal free play and push rod play.

      1. Loosen the lock nut and turn the push rod until the clutch pedal free play and push rod play are correct.
      2. Tighten the lock nut.
      3. After adjusting the clutch pedal free play and push rod play, check the clutch pedal height.

        Standard Clutch Pedal Height from Tibia Pad:
        164.8 to 174.8 mm (6.49 to 6.88 in.)

      Torque:
      12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    5. CL00512E17
      Check the clutch release point.
      1. Pull the parking brake lever and chock the wheels.
      2. Start the engine and allow it to idle.
      3. Without depressing the clutch pedal, slowly move the shift lever to R until the gears engage.
      4. Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

        Standard Distance from Pedal Stroke End Position to Release Point:
        20 mm (0.787 in.) or more

        If the distance is not as specified, perform the following operations:
        1. Check the clutch pedal height.
        2. Check the push rod play and pedal free play.
        3. Bleed the clutch line.
        4. Check the clutch cover and disc.


INITIALIZATION RELATED TO ACTIVE HEIGHT CONTROL SUSPENSION
  1. DESCRIPTION

    1. If replacing the suspension control ECU and/or height control sensor, perform the vehicle height offset calibration.

  2. VEHICLE HEIGHT OFFSET CALIBRATION

    NOTICE:
    1. Make sure that the pressure of the tires is normal.
    2. Make sure that the vehicle is empty.
    3. Make sure that the parking brake is released and that the shift lever is in N.

  3. PERFORM VEHICLE HEIGHT INSPECTION

    1. Adjust the pressure of the tires.

    2. Stabilize the suspension by releasing the parking brake and bouncing the corners of the vehicle up and down.

    3. Start the engine.

    4. Perform the following operation twice:
      Set the vehicle height to LO with the height control switch, and then return the vehicle height to NORMAL.

    5. Turn the engine switch off.

    6. Connect the intelligent tester to the DLC3.

    7. Move the shift lever to N and move the vehicle forward and rearward.

    8. Turn the engine switch on (IG) and the tester on.

    9. Check that the vehicle height is NORMAL.

      HINT:
      The N of the multi-information display height control indicator in the combination meter turns on.

    10. C171986E01
      Perform the vehicle height inspection.

      Measuring points:
      A:
      Ground clearance of front wheel center
      B:
      Ground clearance of the front adjusting cam bolt center
      C:
      Ground clearance of the rear axle shaft center
      D:
      Ground clearance of the rear lower control arm front side center


      Standard Vehicle Height:
      Front (A minus B)
      Rear (C minus D)
      101 mm (3.98 in.)
      94 mm (3.70 in.)

    11. Using a jack, set the vehicle to the standard vehicle height and eliminate any difference in height between the left and right sides of the vehicle.

      NOTICE:
      The vehicle height may be outside the calibration range if there is a difference in height between the left and right sides of the vehicle.

    12. Using the intelligent tester, enter the following menus: Chassis / AHC / Data List. Then read and record the values for "After Height Adjust" and "Height Adjust" for each wheel.

      AHC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnosis Note
      FR Height Adjust
      Display of vehicle height offset recorded value of front right wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      FL Height Adjust
      Display of vehicle height offset recorded value of front left wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      RR Height Adjust
      Display of vehicle height offset recorded value of rear right wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      RL Height Adjust
      Display of vehicle height offset recorded value of rear left wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      FR After Height Adjust
      Display of after-calibration vehicle height value of front right wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      FL After Height Adjust
      Display of after-calibration vehicle height value of front left wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      RR After Height Adjust
      Display of after-calibration vehicle height value of rear right wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -
      RL After Height Adjust
      Display of after-calibration vehicle height value of rear left wheel /
      min.: -3276.8 mm (-129 in.)
      max.: 3276.7 mm (129 in.)
      -
      -

    13. Turn the engine switch off.

  4. PERFORM VEHICLE HEIGHT OFFSET CALIBRATION

    NOTICE:
    The possible vehicle height automatic adjustment value is 20 mm (0.787 in.). If the "Height Adjust value + (Standard value - Measurement value - After Height Adjust value)" is 20 mm (0.787 in.) or more, first perform the vehicle height adjustment for the front side, and for the rear side.


    1. Turn the engine switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the engine switch on (IG) and the tester on.

    4. Enter the following menus: Chassis / AHC / Utility / Height offset.

    5. For each wheel, follow the instructions on the tester screen and input the input value to complete the vehicle height offset calibration.

      HINT:
      Input value = Measurement value and standard value

    6. Remove the jack.

    7. Start the engine.

    8. Set the vehicle height to LO and check that LO of the multi-information display height control indicator stops blinking and illuminates.

    9. Set the vehicle height to NORMAL and check that N of the height control indicator stops blinking and illuminates.

    10. Turn the engine switch off.

    11. Perform the vehicle height inspection. Check that the result is within +/-8 mm (+/-0.315 in.) of the standard value.

    12. Perform yaw rate and G sensor zero point calibration.


CALIBRATION RELATED TO ANTI-LOCK BRAKE SYSTEM
  1. DESCRIPTION
    After replacing the relevant ABS components, clear the sensor calibration data and then perform calibration.

    Replacement/Adjustment Part
    Necessary Operation
    Skid control ECU (Master cylinder solenoid)
    Deceleration sensor zero point calibration
    Deceleration sensor
    1. Clearing zero point calibration data
    2. Deceleration sensor zero point calibration

  2. CLEAR ZERO POINT CALIBRATION (SST CHECK WIRE)
    After replacing the deceleration sensor, make sure to clear the zero point calibration data in the skid control ECU (master cylinder solenoid) and perform zero point calibration.

    1. Turn the ignition switch to ON.

    2. C146309E15
      Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.
      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3
      SST
      09843-18040  

    3. Check that the ABS warning light comes on.

    4. Using a check wire, perform zero point calibration of the deceleration sensor.

  3. PERFORM ZERO POINT CALIBRATION OF DECELERATION SENSOR (SST CHECK WIRE)
    After replacing the master cylinder solenoid and/or deceleration sensor, make sure to perform deceleration sensor zero point calibration.

    NOTICE:
    1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it. Keep it stationary and do not start the engine.
    2. Choose a level surface with an inclination of less than 1°.


    1. Procedures for Test Mode:

      SST
      09843-18040  
      1. Turn the ignition switch off.
      2. for A/T:
        Move the shift lever to P.

        NOTICE:
        DTC 98 will be stored if the shift lever is not in P.

      3. for M/T:
        Pull the parking brake lever.

        NOTICE:
        DTC 98 will be stored if the parking brake lever is not pulled.


      4. C146309E15
        Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
        Text in Illustration 
        *a
        Front view of DLC3
      5. Check that the steering wheel is centered.
      6. Turn the ignition switch to ON.
      7. Keep the vehicle stationary on a level surface for 2 seconds or more.
      8. Check that the ABS warning light is blinking in test mode pattern (0.125 seconds on and 0.125 seconds off).

        NOTICE:
        The ABS warning light stays on when obtaining the zero point.

        HINT:
        1. If the ABS warning light does not blink, perform the zero point calibration again.
        2. The zero point calibration is performed only once after the system enters test mode.
        3. Calibration cannot be performed again until the stored data is cleared once.

  4. CLEAR ZERO POINT CALIBRATION (GTS)
    After replacing the deceleration sensor, make sure to clear the zero point calibration data in the skid control ECU (master cylinder solenoid) and perform zero point calibration.

    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.

    6. Using the GTS, perform zero point calibration of the deceleration sensor.

  5. PERFORM ZERO POINT CALIBRATION OF DECELERATION SENSOR (GTS)
    After replacing the master cylinder solenoid and/or deceleration sensor, make sure to perform deceleration sensor zero point calibration.

    NOTICE:
    1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it. Keep it stationary and do not start the engine.
    2. Choose a level surface with an inclination of less than 1°.


    1. Procedures for Test Mode:

      1. Turn the ignition switch off.
      2. for A/T:
        Move the shift lever to P.

        NOTICE:
        DTC C1336 will be stored if the shift lever is not in P.

      3. for M/T:
        Pull the parking brake lever.

        NOTICE:
        DTC C1336 will be stored if the parking brake lever is not pulled.

      4. Check that the steering wheel is centered.
      5. Connect the GTS to the DLC3.
      6. Turn the ignition switch to ON.
      7. Turn the GTS on.
      8. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.
      9. Keep the vehicle stationary on a level surface for 2 seconds or more.
      10. Check that the ABS warning light is blinking in test mode pattern (0.125 seconds on and 0.125 seconds off).

        NOTICE:
        The ABS warning light stays on when obtaining the zero point.

        HINT:
        1. If the ABS warning light does not blink, perform the zero point calibration again.
        2. The zero point calibration is performed only once after the system enters test mode.
        3. Calibration cannot be performed again until the stored data is cleared once.


CALIBRATION RELATED TO VEHICLE STABILITY CONTROL SYSTEM
  1. DESCRIPTION
    After replacing the relevant VSC components or performing a vehicle height adjustment, clear the sensor calibration data and perform calibration.

    Replacement/Adjustment Part
    Necessary Operation
    Skid Control ECU (Master Cylinder Solenoid)
    1. Clearing zero point calibration data
    2. Yaw rate and acceleration sensor zero point calibration
    Yaw Rate Sensor Assembly
    1. Clearing zero point calibration data
    2. Yaw rate and acceleration sensor zero point calibration
    Vehicle height adjustment
    1. Clearing zero point calibration data
    2. Yaw rate and acceleration sensor zero point calibration
    3. Steering sensor initialization

  2. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND SYSTEM INFORMATION (WHETHER VGRS IS EQUIPPED) (When Using GTS)

    NOTICE:
    1. While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
    2. Be sure to perform this procedure on a level surface (with an inclination of less than 1%).

    1. Clear the zero point calibration and system information data.
      1. Turn the ignition switch off.
      2. Check that the steering wheel is centered.
      3. Check that the shift lever is in P.
      4. Connect the GTS to the DLC3.
      5. Turn the ignition switch to ON.
      6. Turn the GTS on.
      7. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.
      8. Select the skid control ECU (master cylinder solenoid) to clear the zero point calibration data using the GTS.
      9. Turn the ignition switch off.
    2. Perform zero point calibration of the yaw rate and acceleration sensor and store the system information.
      1. Turn the ignition switch off.
      2. Check that the steering wheel is centered.
      3. Check that the shift lever is in P.

        NOTICE:
        1. DTCs C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) and C1336 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P.
        2. If a DTC is output that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.

      4. Connect the GTS to the DLC3.
      5. Turn the ignition switch to ON.
      6. Turn the GTS on.
      7. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.
      8. Keep the vehicle stationary on a level surface for 5 seconds or more.
      9. Check that the slip indicator light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

        HINT:
        1. If the slip indicator light does not blink, perform zero point calibration again.
        2. The zero point calibration is performed only once after the system enters test mode.
        3. Calibration cannot be performed again until the stored data is cleared.

      10. Turn the ignition switch off and disconnect the GTS.
    3. Check if DTC C120A (ECU Initial Setting Incomplete) is output.

      HINT:
      If DTC C120A is not output, calibration was performed successfully.

  3. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND SYSTEM INFORMATION (WHETHER VGRS IS EQUIPPED) (When Using SST Check Wire)

    NOTICE:
    1. While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
    2. Be sure to perform this procedure on a level surface (with an inclination of less than 1%).


    1. Clear the zero point calibration and system information data.

      SST
      09843-18040  
      1. Turn the ignition switch off.
      2. Check that the steering wheel is centered.
      3. Check that the shift lever is in P.
      4. Turn the ignition switch to ON.

      5. C146309E15
        Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.
        Text in Illustration 
        *a
        Front view of DLC3
      6. Check that the slip indicator light comes on.

    2. Perform zero point calibration of the yaw rate and acceleration sensor and store the system information.

      SST
      09843-18040  
      1. Turn the ignition switch off.
      2. Check that the steering wheel is centered.
      3. Check that the shift lever is in P.

        NOTICE:
        1. DTCs 36 (Zero Point Calibration of Yaw Rate Sensor Undone) and 98 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P.
        2. If a DTC is output that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.


      4. C146309E15
        Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
        Text in Illustration 
        *a
        Front view of DLC3
      5. Turn the ignition switch to ON.
      6. Keep the vehicle stationary on a level surface for 5 seconds or more.
      7. Check that the slip indicator light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

        HINT:
        1. If the slip indicator light does not blink, perform zero point calibration again.
        2. The zero point calibration is performed only once after the system enters test mode.
        3. Calibration cannot be performed again until the stored data is cleared.

      8. Turn the ignition switch off and disconnect SST from the DLC3.

    3. Check if DTC 13 (ECU Initial Setting Incomplete) is output.

      HINT:
      If DTC 13 is not output, calibration was performed successfully.


ADJUSTMENT FOR BREAK PEDAL (for LHD)

  1. CHECK BRAKE PEDAL HEIGHT

    1. C222463E01
      Check the brake pedal height.

      Standard Pedal Height from No. 2 Dash Panel Insulator Pad:
      147.1 to 157.1 mm (5.80 to 6.18 in.)

      NOTICE:
      Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

      If the pedal height is incorrect, adjust the rod operating adapter length.

    2. C172191E01
      Adjust the rod operating adapter length.
      1. Remove the clip and clevis pin.
      2. Loosen the clevis lock nut.
      3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

        Standard Rod Operating Adapter Length "A":
        201.7 to 202.7 mm (7.94 to 7.98 in.)

      4. Tighten the clevis lock nut.
      5. Set the master cylinder push rod clevis in place, insert the push rod pin from the outside of the vehicle and then install a new clip.
        If the pedal height is incorrect even if the rod operating adapter is adjusted, check that there is no damage in the brake pedal, brake pedal lever, brake pedal support and dash panel.
        1. Even if there is damage, there is no problem if the reserve distance is within the standard value.
        2. If necessary, replace any damaged parts.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

  2. CHECK AND ADJUST STOP LIGHT SWITCH ASSEMBLY

    HINT:
    If the pedal height is incorrect, check and adjust the stop light switch clearance.


    1. Disconnect the stop light switch assembly connector from the stop light switch assembly.

    2. Turn the stop light switch assembly counterclockwise and remove the stop light switch assembly.

    3. C172890E01
      Insert the stop light switch assembly until the body hits the brake pedal bracket.

      NOTICE:
      When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.

    4. Turn the stop light switch assembly a quarter turn clockwise to install it.

      HINT:
      Turning the stop light switch assembly counterclockwise loosens the switch.

    5. Connect the stop light switch connector to the stop light switch assembly.

    6. Check the protrusion of the rod.

      Standard Rod Protrusion:
      1.5 to 2.5 mm (0.0591 to 0.0984 in.)

    7. After adjusting the pedal height, check the pedal free play.

  3. CHECK PEDAL FREE PLAY

    1. C172192E01
      Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown in the illustration.

      Standard Pedal Free Play:
      1 to 6 mm (0.0394 to 0.236 in.)

  4. CHECK PEDAL RESERVE DISTANCE

    1. C222462E01
      Release the parking brake lever.
      With the engine running, depress the pedal and measure the pedal reserve distance as shown in the illustration.

      Standard Pedal Reserve Distance from No. 2 Dash Panel Insulator Pad at 490 N (50 kgf, 110.2 lbf):
      More than 67 mm (2.64 in.)

      If incorrect, troubleshoot the brake system.


ADJUSTMENT FOR BREAK PEDAL (for RHD)

  1. CHECK BRAKE PEDAL HEIGHT

    1. C222463E01
      Check the brake pedal height.

      Standard Pedal Height from No. 2 Dash Panel Insulator Pad:
      149.1 to 159.1 mm (5.87 to 6.26 in.)

      NOTICE:
      Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

      If the pedal height is incorrect, adjust the rod operating adapter length.

    2. C172191E01
      Adjust the rod operating adapter length.
      1. Remove the clip and clevis pin.
      2. Loosen the clevis lock nut.
      3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

        Standard Rod Operating Adapter Length "A":
        201.7 to 202.7 mm (7.94 to 7.98 in.)

      4. Tighten the clevis lock nut.
      5. Set the master cylinder push rod clevis in place, insert the push rod pin from the outside of the vehicle and then install a new clip. If the pedal height is incorrect even if the rod operating adapter is adjusted, check that there is no damage in the brake pedal, brake pedal lever, brake pedal support and dash panel.
        1. Even if there is damage, there is no problem if the reserve distance is within the standard value.
        2. If necessary, replace any damaged parts.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

  2. CHECK AND ADJUST STOP LIGHT SWITCH ASSEMBLY

    HINT:
    If the pedal height is incorrect, check and adjust the stop light switch clearance.


    1. Disconnect the stop light switch assembly connector from the stop light switch assembly.

    2. Turn the stop light switch assembly counterclockwise and remove the stop light switch assembly.

    3. C172890E01
      Insert the stop light switch assembly until the body hits the brake pedal bracket.

      NOTICE:
      When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.

    4. Turn the stop light switch assembly a quarter turn clockwise to install it.

      HINT:
      Turning the stop light switch assembly counterclockwise loosens the switch.

    5. Connect the stop light switch connector to the stop light switch.

    6. Check the protrusion of the rod.

      Standard Rod Protrusion:
      1.5 to 2.5 mm (0.0591 to 0.0984 in.)

    7. After adjusting the pedal height, check the pedal free play.

  3. CHECK PEDAL FREE PLAY

    1. C172192E01
      Push in the pedal until the beginning of the resistance is felt. Measure the pedal free play.

      Standard Pedal Free Play:
      1 to 6 mm (0.0394 to 0.236 in.)

  4. CHECK PEDAL RESERVE DISTANCE

    1. C222462E01
      Release the parking brake lever.
      With the engine running, depress the pedal and measure the pedal reserve distance as shown in the illustration.

      Standard Pedal Reserve Distance from No. 2 Dash Panel Insulator Pad at 490 N (50 kgf, 110.2 lbf):
      More than 67.5 mm (2.66 in.)

      If incorrect, troubleshoot the brake system.


ADJUSTMENT FOR PARKING BREAK SYSTEM
  1. INSPECT PARKING BRAKE LEVER TRAVEL

    1. Fully pull the parking brake lever to engage the parking brake.

    2. Release the lever to disengage the parking brake.

    3. Slowly pull the parking brake lever all the way, and count the number of clicks

      Standard Parking Brake Lever Travel when Pulled with a Force of 200 N (20 kgf, 45 lbf):
      5 to 7 clicks

      If the parking brake lever travel is not as specified, adjust the parking brake shoe clearance and parking brake lever travel.

  2. REMOVE REAR WHEEL

  3. ADJUST PARKING BRAKE LEVER TRAVEL

    1. Remove the console cup holder box sub-assembly.

    2. Completely release the parking brake lever.

    3. C170906
      Loosen the adjusting nut to completely release the parking brake cable.

    4. Temporarily install the hub nuts.

    5. Remove the hole plug.

    6. C158874E01
      Insert an adjustment tool into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.

    7. Check that the disc can be rotated lightly. If not, rotate the adjustment wheel in the "Y" direction and check again.

    8. Install the hole plug.

    9. Remove the hub nuts.

    10. C170906
      Turn the adjusting nut until the parking brake lever travel becomes correct.

      Standard Parking Brake Lever Travel when Pulled with a Force of 200 N (20 kgf, 45 lbf):
      5 to 7 clicks

    11. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

      Standard Parking Brake Lever Travel when Pulled with a Force of 200 N (20 kgf, 45 lbf):
      5 to 7 clicks

    12. Check whether the parking brake drags or not.

    13. When operating the parking brake lever, check that the brake warning light comes on.

      Standard Condition:
      The brake warning light always illuminates at the first click.

    14. Install the console cup holder box sub-assembly.

  4. INSTALL REAR WHEEL

    Torque:
    131 N*m{ 1,336 kgf*cm , 97 ft.*lbf }


INITIALIZATION RELATED TO VGRS SYSTEM
  1. STEERING ANGLE SENSOR INITIALIZATION (to obtain a tire angle (during straight-ahead driving) signal)

    1. Turn the engine switch on (IG), and check that the master warning light illuminates for a few seconds.

      NOTICE:
      If the warning light remains on, repair the applicable system.

    2. Drive the vehicle on a straight road at 35 km/h (22 mph) or more for 5 seconds or more.

      HINT:
      1. At this point, the steering wheel will still remain off-center by 5 to 10°.
      2. In this step, the neutral position of the steering wheel is restored from the steering control ECU memory.

    3. Confirm that steering angle sensor initialization is completed (using the tester).

      1. Enter the VGRS menu using the tester. Select "Straight Angle Valid Flag" from "Data List". Check if the steering angle sensor has obtained a tire angle (during straight-ahead driving) signal.

        Standard:
        "Valid" is displayed on the tester screen.

    4. Confirm that steering angle sensor initialization is completed (not using the tester).

      1. Stop the vehicle (engine running).
      2. Slowly turn the steering wheel from lock to lock.
      3. If it turns approximately 2.7 turns, steering angle sensor initialization is completed. If it turns approximately 3.2 turns, steering angle sensor initialization is not completed.

        NOTICE:
        If the steering wheel turns approximately 3.2 turns, drive the vehicle on a straight road at 35 km/h (22 mph) or more for 5 seconds or more. Then confirm the initialization again.

  2. VGRS SYSTEM CALIBRATION PROCEDURE (WHEN USING SST CHECK WIRE)

    NOTICE:
    Use this procedure to center the steering wheel if:
    1. The steering actuator assembly has been replaced.
    2. The steering control ECU has been replaced.
    3. The steering column or steering intermediate shaft has been disconnected.
    4. The steering wheel is still off-center after completing the steering angle sensor initialization.


    1. FACE TIRES STRAIGHT AHEAD (Procedure A)

      NOTICE:
      Drive the vehicle to confirm that the steering wheel is centered.

    2. CHECK DTC (Procedure B)

      1. Check for DTCs.
        Result 
        Result
        Proceed to
        DTC C1591/51 is not output
        Procedure C
        DTC C1591/51 is output
        Procedure D

    3. PERFORM ACTUATOR ANGLE INITIALIZATION (Procedure C)

      SST
      09843-18040  

      NOTICE:
      If the procedures from *1 to *2 are not completed within 1 minute, or if errors are made during these procedures, perform the initialization again from the beginning.


      1. H102392E81
        Start the engine.
      2. Center the steering wheel.
      3. Using SST, connect terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) of the DLC3.*1
      4. Disconnect SST from terminal 12 (TS) of the DLC3, and turn the steering wheel to the left 180° or more.
      5. Connect SST to terminal 12 (TS) of the DLC3.
      6. Disconnect SST from terminal 13 (TC) of the DLC3, and turn the steering wheel to the right 180° or more.
      7. Connect SST to terminal 13 (TC) of the DLC3.*2

        HINT:
        If the master warning light comes on, DTC C1591/51 is stored.

      8. Disconnect SST from the DLC3.
      9. Turn the engine switch off.

    4. FACE TIRES STRAIGHT AHEAD (Procedure D)

      1. Confirm that the steering wheel is centered when facing the tires straight ahead.

        NOTICE:
        Drive the vehicle to confirm that the steering wheel is centered.

        Result 
        Result
        Proceed to
        Steering wheel is off-center
        Procedure E
        Steering wheel is centered
        Procedure H

    5. UNLOCK STEERING ACTUATOR (Procedure E)

      NOTICE:
      Make sure the engine is not running.

      1. Turn the engine switch off.
      2. Disconnect the cable from the negative (-) battery terminal.

      3. C140769E04
        Disconnect the E80 connector from the steering actuator.
      4. Connect a jumper wire from terminal 7 (LV+) of the steering actuator to the positive (+) 12 V battery terminal and another jumper wire from terminal 16 (LG+) of the steering actuator to the negative (-) 12 V battery terminal.

        NOTICE:
        Do not apply voltage for more than 3 minutes.

    6. STEERING CENTER ADJUSTMENT (Procedure F)

      1. Center the steering wheel.

        NOTICE:
        If the centering of the spiral cable was not confirmed when the steering wheel was installed, confirm the centering of the spiral cable.

    7. LOCK STEERING ACTUATOR (Procedure G)

      1. Disconnect the positive (+) and negative (-) 12 V battery jumper wires from the steering actuator.
      2. Connect the E80 connector to the steering actuator.
      3. Connect the cable to the negative (-) battery terminal.
      4. Turn the steering wheel approximately 3° to the left and right. Confirm that the reaction force can be felt.

        NOTICE:
        1. If the above procedures are not followed correctly, a DTC will be stored. If a DTC is stored, perform the above procedures again and then check for DTCs.
        2. Perform these procedures with the engine switch off.

    8. ADJUST ACTUATOR ANGLE (Procedure H)

      HINT:
      Activating and ending test mode will complete actuator angle adjustment.

      SST
      09843-18040  
      1. Make sure the engine switch is off.

        NOTICE:
        Do not touch the steering wheel during these procedures.


      2. H102392E80
        Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
      3. Turn the engine switch on (IG).
      4. Confirm that "VGRS Test Mode" is displayed on the multi-information display when test mode is activated.

        HINT:
        Wait approximately 5 seconds.

      5. Turn the engine switch off.
      6. Disconnect SST from terminals 12 (TS) and 4 (CG) of the DLC3.
      7. Turn the engine switch on (IG) again.

    9. CHECK MASTER WARNING LIGHT (Procedure I)

      1. Confirm that the master warning light is off.
      2. Turn the engine switch off, then on (IG).
      3. Confirm that the master warning light is operating normally.

    10. CHECK STEERING WHEEL OPERATION (Procedure J)

      1. Start the engine.
      2. Perform the steering angle sensor initialization.
      3. Turn the steering wheel from lock to lock and check that it rotates approximately 2.7 turns.
      4. Drive the vehicle and confirm that the steering wheel is centered.

  3. VGRS SYSTEM CALIBRATION PROCEDURE (WHEN USING INTELLIGENT TESTER)

    1. FACE TIRES STRAIGHT AHEAD (Procedure A)

      NOTICE:
      Drive the vehicle to confirm that the steering wheel is centered.

    2. PERFORM VGRS SYSTEM CALIBRATION (Procedure B)

      1. Connect the intelligent tester to the DLC3.
      2. Turn the engine switch on (IG).
      3. Turn the tester on.
      4. Enter the following menus: Chassis / VGRS / Utility / Steering Angle Adjust.
        Then, press "Next".
      5. Follow the instructions on the tester, and press "Next".

        NOTICE:
        Press the "Next" key even if DTC C15B4/71 is output.

      6. Follow the instructions on the tester, and press "Next".
      7. Follow the instructions on the tester, and press "Next".

        NOTICE:
        Ensure that the engine switch is off.

      8. Follow the instructions on the tester, and press "Next".
      9. Follow the instructions on the tester, and press "Next".

        NOTICE:
        If the centering of the spiral cable was not confirmed when the steering wheel was installed, confirm the centering of the spiral cable.

      10. Follow the instructions on the tester, and press "Next".

        NOTICE:
        Do not touch the steering wheel during these procedures.

      11. Follow the instructions on the tester, and press "Next".
      12. Follow the instructions on the tester, and press "Next".

        NOTICE:
        Do not touch the steering wheel during these procedures.

      13. "NOW CALIBRATING" is displayed and the display switches automatically to the next screen.

        NOTICE:
        Do not touch the steering wheel during these procedures.

      14. "Steering Angle Adjust is complete." is displayed. Then, check that the VGRS system calibration is completed normally.
      15. Select "Exit" to return the display to the "MENU" screen.

    3. CHECK MASTER WARNING LIGHT (Procedure C)

      1. Confirm that the master warning light is off.
      2. Turn the engine switch off.
      3. Disconnect the intelligent tester from the DLC3.
      4. Turn the engine switch on (IG).
      5. Confirm that the master warning light is operating normally.

    4. CHECK STEERING WHEEL OPERATION (Procedure D)

      1. Start the engine.
      2. Perform the steering angle sensor initialization.
      3. Turn the steering wheel from lock to lock and check that it rotates approximately 2.7 turns.
      4. Drive the vehicle and confirm that the steering wheel is centered.


ADJUSTMENT FOR STEERING SYSTEM
  1. STEERING OFF CENTER ADJUSTMENT PROCEDURE

    HINT:
    This is the adjustment procedure for when the steering is off center.


    1. Check if the steering wheel is off center.


      1. C170782E01
        Apply masking tape to the top center of the steering wheel and steering column upper cover.
      2. Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), and hold the steering wheel to maintain the course.

      3. C170783E02
        Draw a line on the masking tape as shown in the illustration.
      4. Turn the steering wheel to the center position.

        HINT:
        Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.


      5. C170784E01
        Draw a new line on the masking tape on the steering wheel as shown in the illustration.
      6. Measure the distance between the 2 lines on the masking tape on the steering wheel.
      7. Convert the measured distance to steering angle.

        HINT:
        1. Measured distance of 1 mm (0.0394 in.) = Steering angle of approximately 1°.
        2. Make a note of the steering angle.

    2. Adjust the steering angle.


      1. C170785E01
        Put matchmarks on the RH and LH tie rod ends and rack ends where it can be easily seen.
      2. Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

        HINT:
        1. Measure both the RH and LH sides.
        2. Make a note of the measured values.


      3. C159206
        Remove the RH and LH boot clips from the rack boots.
      4. Loosen the RH and LH lock nuts.
      5. Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle.

        HINT:
        One 360° turn of the rack end (1.5 mm (0.0591 in.) horizontal movement) equals 11° of steering angle.

      6. Tighten the RH and LH lock nuts to the specified torque.

        NOTICE:
        Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).

      7. Install the RH and LH boot clips.

      Torque:
      82 N*m{ 836 kgf*cm , 60 ft.*lbf }


INITIALIZATION RELATED TO PARKING ASSIST MONITOR SYSTEM (w/ Side Monitor System)
  1. INITIALIZE PARKING ASSIST MONITOR SYSTEM

    1. When "System initializing" is displayed on the multi-display assembly, correct the steering angle neutral point using the following method.

      1. Fully turn the steering wheel to the right and left on flat ground.

        NOTICE:
        Memorizing the steering angle neutral point must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.

        HINT:
        The "?" button is displayed at the same time as "System initializing". If the "?" button is selected, this method is displayed.


CALIBRATION RELATED TO PARKING ASSIST MONITOR SYSTEM (w/ Side Monitor System)
  1. ADJUST PARKING ASSIST MONITOR SYSTEM

    1. This parking assist monitor system (w/ Side Monitor System) can be set from the diagnostic screen of the multi-display assembly.

    2. If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

      Part Name
      Operation
      Adjustment Item
      Proceed to
      Steering sensor
      1. Removal and installation of the Steering angle sensor
      2. Removal and installation of the connector of the steering sensor
      Steering angle neutral point (Initialize parking assist monitor system [w/ Side Monitor System])
      -
      Steering angle setting
      Procedure 2
      Replacement
      Steering angle neutral point (Initialize parking assist monitor system [w/ Side Monitor System])
      -
      Steering angle setting
      Procedure 2
      Multi-media module receiver assembly
      Replacement
      Vehicle contract setting
      -
      Parking assist ECU
      Replacement
      Parking assist ECU initialization
      Procedure 1
      Suspension, tires, etc.
      The vehicle height changes because of suspension or tire replacement
      Rear television camera optical axis (Back camera position setting)
      Procedure 3
      Side television camera optical axis (Side camera position setting)
      -
      Rear television camera assembly
      1. Replacement
      2. Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.
      Rear television camera optical axis (Back camera position setting)
      Procedure 3

      NOTICE:
      After the engine switch is turned off, the multi-media module receiver assembly requires approximately a minute to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      HINT:
      The adjustment values stored while performing parking assist monitor system (w/ Side Monitor System) calibration are stored in the parking assist ECU.

  2. PARKING ASSIST ECU INITIALIZATION (Procedure 1)

    HINT:
    Be sure to check for DTCs before performing this procedure.


    1. Preparation for adjustment

      1. Park the vehicle with the steering wheel centered.

      2. E181012E03
        Set a target bar for optical axis adjustment of the rear television camera.

        HINT:
        Only when adjusting the optical axis of the camera, create a target bar for adjustment.

        Dimension:
        Area
        Specification
        A
        825 to 835 mm (2.71 to 2.74 ft.)
        B
        1995 to 2005 mm (6.55 to 6.58 ft.)

        Text in Illustration 
        *a
        Vehicle Center
        *b
        Target Bar for Back Camera Adjustment
        *c
        Vehicle End
        *d
        Front Side

        HINT:
        1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-media module receiver assembly and choose a tape color which can be easily seen.
        2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
        3. Check that the back door is fully closed.


      3. Set a target bar for optical axis adjustment of the side television camera.

        HINT:
        Only when adjusting the optical axis of the camera, create a target bar for adjustment.


        E180069E06
        Text in Illustration 
        *A
        for LHD
        -
        -
        *a
        Target Bar for Side Camera Adjustment
        *b
        Front Wheel Axis
        *c
        Front Side
        *d
        Vehicle Center

        E180068E04

        Dimension:
        A
        B
        C
        D
        E
        F
        1183 mm
        (3.88 ft.)
        1181 mm
        (3.87 ft.)
        500 mm
        (1.64 ft.)
        500 mm
        (1.64 ft.)
        500 mm
        (1.64 ft.)
        180 mm
        (7.09 in.)

        Text in Illustration 
        *A
        for RHD
        -
        -
        *a
        Target Bar for Side Camera Adjustment
        *b
        Front Wheel Axis
        *c
        Front Side
        *d
        Vehicle Center

        HINT:
        Target bars for side camera adjustment should be made with 2 pieces of 2.5 cm wide tape; one piece should be 100 cm (3.28 ft.) (C+D) and the other should be 68 cm (2.23 ft.) (E+F) long. Check the tape color on the multi-display assembly and choose a tape color which can be easily seen.

    2. Start diagnostic mode.

      NOTICE:
      Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

      HINT:
      The displayed items may differ depending on vehicle specifications.


      1. E248980
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E248981
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E252019
        Select "Next" on the [Signal Check] screen.

        NOTICE:
        1. When "CHK" (red) is displayed for any items on the [Signal Check] screen, selecting "Next" will not change the screen to the [Side Camera Position Setting] screen.
        2. When "CHK" (red) is displayed for any items on the [Signal Check] screen, perform inspections using the [Signal Check] screen.

        HINT:
        1. When the outer mirrors are retracted, selecting "Next" will not change the screen to the [Side Camera Position Setting] screen.
        2. If the screen does not change to the [Side Camera Position Setting] screen even though the outer mirrors are extended, perform the "MIRROR SW" check on the [Signal Check] screen.
        3. If the screen does not change to the [Side Camera Position Setting] screen even after "OK" (blue) is displayed as a result of the MIRROR SW check on the [Signal Check] screen, replace the parking assist ECU.

    3. E181004E02
      Side Camera Position Setting:

      HINT:
      Colors used on the [Side Camera Position Setting] screen

      Text in Illustration 
      *a
      Target Adjustment Bar for Side Camera Position Setting
      *b
      Red Frame
      *c
      Yellow Frame

      1. E246955E02
        Perform the roll angle adjustment.
        1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      2. Perform the vertical and horizontal position adjustment.
        1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      3. Select "Next" to display [Side Verify Mode].

    4. Side Verify Mode:


      1. E246956
        Check that the red cross and the target adjustment bar are aligned.

        HINT:
        If they are not aligned, select "Back" and perform [Side Camera Position Setting] again.

      2. Select "Next" to display [Side Camera Signal Check].

    5. Side Camera Signal Check:


      1. E248973
        Select "Next" to store the side camera aiming adjustment value and change the screen to the [Steering Angle Setting] screen.

        HINT:
        1. When "Next" is selected, a beep will sound to confirm that the side camera aiming adjustment values have been stored.
        2. The adjustment value will not be stored unless "Next" is selected.

    6. Steering Angle Setting:


      1. E246957
        Perform the "STEERING CENTER MEMORIZE" operation.
        1. Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".

          HINT:
          When performing removal and installation, or replacement of the television camera, steering angle adjustment is not required.

      2. Perform the "MAX STEERING ANGLE MEMORIZE" operation.
        1. After adjusting the steering angle neutral point, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the [Back Camera Position Setting] screen.

          HINT:
          1. The "Next" button does not respond until the system stores the steering angle neutral point and maximum steering angle.
          2. It is also possible to start by initially turning the steering to the right side.
          3. When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering adjustment values have been stored.
          4. The adjustment value will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel side to side.
          5. When "Back" is selected, the screen changes to [Side Verify Mode] without storing the set values.
          6. Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment value to be stored if the steering sensor is malfunctioning.
          7. If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.

    7. E246958E02
      Back Camera Position Setting:

      HINT:
      1. When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
      2. If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed).

      1. Perform the roll angle adjustment.
        1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      2. Perform the vertical and horizontal position adjustment.
        1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      3. Select the "Next" to display [Back Verify Mode].

    8. Back Verify Mode:


      1. E246959E01
        Check that A and the target adjustment bar are overlapping.
        1. If the steering angle neutral point is not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.
        2. If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the camera position setting operation.
      2. Selecting "OK" will return the screen to the [Service Menu] screen, and complete the adjustment.

        HINT:
        1. The update is not completed until "OK" is selected.
        2. When "OK" is selected, a beep will sound to confirm that the rear camera aiming adjustment values have been stored.

    9. Finish diagnostic mode.

  3. STEERING ANGLE SETTING (Procedure 2)

    1. Preparation for adjustment

      1. Park the vehicle with the steering wheel centered.

    2. Start diagnostic mode.

      NOTICE:
      Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

      HINT:
      The displayed items may differ depending on vehicle specifications.


      1. E248980
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E248981
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E246954
        Select "Steering Angle Setting" on the [Mode Setting] screen.

        HINT:
        To select a grayed out item, select and hold the item for 2 seconds or more.


      4. E252019
        Select "Next" on the [Signal Check] screen.

        NOTICE:
        1. When "CHK" (red) is displayed for any items on the [Signal Check] screen, selecting "Next" will not change the screen to the [Steering Angle Setting] screen.
        2. When "CHK" (red) is displayed for any items on the [Signal Check] screen, perform inspections using the [Signal Check] screen.

    3. Steering Angle Setting:


      1. E248974
        Perform the "STEERING CENTER MEMORIZE" operation.
        1. Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".

          HINT:
          When performing removal and installation, or replacement of the television camera, steering angle adjustment is not required.

      2. Perform the "MAX STEERING ANGLE MEMORIZE" operation.
        1. After adjusting the steering angle neutral point, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the [Mode Setting] screen.

          HINT:
          1. The "Next" button does not respond until the system stores the steering angle neutral point and maximum steering angle.
          2. It is also possible to start by initially turning the steering to the right side.
          3. When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering adjustment values have been stored.
          4. The adjustment value will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel side to side.
          5. When "Back" is selected, the screen changes to [Signal Check] without storing the set values.
          6. Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment value to be stored if the steering sensor is malfunctioning.
          7. If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.

      3. Select "OK" to display [Mode Setting].

    4. Finish diagnostic mode.

    5. Confirm steering angle adjustment.

      HINT:
      If the steering angle has been adjusted, confirm the steering angle adjustment on the parking assist monitor screen after finishing diagnostic mode.

      1. Check on the parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.

        HINT:
        If the predicted path line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.

  4. BACK CAMERA POSITION SETTING (Procedure 3)

    HINT:
    Be sure to check for DTCs before performing this procedure.


    1. Preparation for adjustment

      1. Park the vehicle with the steering wheel centered.
      2. Set a target bar for optical axis adjustment of the rear television camera.

        HINT:
        E181012E03
        Only when adjusting the optical axis of the camera, create a target bar for adjustment.

        Dimension:
        Area
        Specification
        A
        825 to 835 mm (2.71 to 2.74 ft.)
        B
        1995 to 2005 mm (6.55 to 6.58 ft.)

        Text in Illustration 
        *a
        Vehicle Center
        *b
        Target Bar for Back Camera Adjustment
        *c
        Vehicle End
        *d
        Front Side

        HINT:
        1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.
        2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
        3. Check that the back door is fully closed.

    2. Start diagnostic mode.

      NOTICE:
      Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

      HINT:
      The displayed items may differ depending on vehicle specifications.


      1. E248980
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E248981
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E246954
        Select "Back Camera Setting" on the [Mode Setting] screen.

        HINT:
        To select a grayed out item, select and hold the item for 2 seconds or more.


      4. E252019
        Select "Next" on the [Signal Check] screen.

        NOTICE:
        1. When "CHK" (red) is displayed for any items on the [Signal Check] screen, selecting "Next" will not change the screen to the [Back Camera Position Setting] screen.
        2. When "CHK" (red) is displayed for any items on the [Signal Check] screen, perform inspections using the [Signal Check] screen.

    3. E246958E02
      Back Camera Position Setting:

      HINT:
      1. When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
      2. If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed).

      1. Perform the roll angle adjustment.
        1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      2. Perform the vertical and horizontal position adjustment.
        1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      3. Select the "Next" button on the [Back Camera Position Setting] screen.

    4. E246959E01
      Back Verify Mode:
      1. Check that A and the target adjustment bar are overlapping.
        1. If the steering angle neutral point is not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.
        2. If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the camera position setting operation.
      2. Selecting "OK" will return the screen to the [Service Menu], and complete the adjustment.

        HINT:
        1. The update is not completed until "OK" is selected.
        2. When "OK" is selected, a beep will sound to confirm that the rear camera aiming adjustment values have been stored.

    5. Finish diagnostic mode.


INITIALIZATION RELATED TO PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System)
  1. INITIALIZE PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System)

    1. When "System initializing" is displayed on the multi-display assembly, correct the steering angle neutral point using the following method.

      1. Fully turn the steering wheel to the right and left on flat ground.

        NOTICE:
        Memorizing the steering angle neutral point must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.

        HINT:
        The "?" button is displayed at the same time as "System initializing". If the "?" button is selected, this method is displayed.


CALIBRATION RELATED TO PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System)
  1. ADJUST PARKING ASSIST MONITOR SYSTEM

    1. This parking assist monitor system (w/o Side Monitor System) can be adjusted using the diagnostic screen of the display.

    2. If the following operations are performed, it is necessary to perform adjustments and checks using the diagnostic screen.

      Part Name
      Operation
      Adjustment Item
      Proceed to
      Steering sensor
      Replacement
      Steering angle neutral point (Initialize parking assist monitor system [w/o Side Monitor System])
      -
      Steering angle setting
      Procedure 3
      1. Removal and installation of the steering sensor
      2. Removal and installation of the connector of the steering sensor
      Steering angle neutral point (Initialize parking assist monitor system [w/o Side Monitor System])
      -
      Steering angle setting
      Procedure 3
      Suspension, tires, etc.
      The vehicle height changes because of suspension or tire replacement
      Rear television camera assembly optical axis (Back camera position setting)
      Procedure 2
      Rear television camera assembly
      1. Replacement
      2. Installation angle of the rear television camera assembly changes because of the removal and installation of the rear television camera assembly, etc.
      Rear television camera assembly optical axis (Back camera position setting)
      Procedure 2
      Multi-media module receiver assembly
      Replacement
      Multi-media module receiver assembly
      Procedure 1

      NOTICE:
      After the engine switch is turned off, the multi-media module receiver assembly requires approximately 60 seconds to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      HINT:
      The adjustment values stored while performing parking assist monitor system calibration are stored in the multi-media module receiver assembly.

  2. MULTI-MEDIA MODULE RECEIVER ASSEMBLY (PROCEDURE 1)

    HINT:
    Be sure to check for DTCs before performing this procedure.


    1. Preparation for adjustment

      1. Park the vehicle with the steering wheel centered.

      2. E181012E03
        Set a target bar for optical axis adjustment of the rear television camera assembly.

        HINT:
        Only when adjusting the optical axis of the camera, create a target bar for adjustment.

        Dimension:
        Area
        Specification
        A
        824 to 834 mm (2.70 to 2.74 ft.)
        B
        1995 to 2005 mm (6.55 to 6.58 ft.)

        Text in Illustration 
        *a
        Vehicle Center
        *b
        Target Bar for Back Camera Adjustment
        *c
        Vehicle End
        *d
        Front

        HINT:
        1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the display and choose a tape color which can be easily seen.
        2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
        3. Check that the back door is fully closed.

    2. Start diagnostic mode.

      NOTICE:
      The following must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.

      NOTICE:
      The following must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.


      1. E226190
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E226193
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E252020
        Select "Next" on the [Car Information Check] screen.

      4. E233967
        Select "Next" on the [Car Signal Check] screen.

        HINT:
        1. When "CHK" (red) is displayed for any items on the [Car Signal Check] screen, selecting "Next" will not change the screen to the "Steering Angle Setting" screen.
        2. When "CHK" (red) is displayed for any items on the [Car Signal Check] screen, perform inspections using the [Car Signal Check] screen.

    3. Steering Angle Setting:


      1. E233968
        Perform the "STEERING CENTER MEMORIZE" operation.
        1. Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".

          HINT:
          When performing removal and installation, or replacement of the rear television camera assembly, steering angle setting is not required.

      2. Perform the "MAX STEERING ANGLE MEMORIZE" operation.
        1. After performing the steering center memorize operation, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the [Back Camera Position Setting] screen.

          HINT:
          The "Next" button does not respond until the system memorizes the steering center and maximum steering wheel angle.

          HINT:
          1. It is also possible to start by initially turning the steering to the right side.
          2. When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the adjustment values have been stored.
          3. The adjustment values will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel from lock to lock.
          4. When "Back" is selected, the screen changes to the [Car Signal Check] screen without storing any values.
          5. Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment values to be stored if the steering sensor is malfunctioning.
          6. If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after performing the steering angle setting procedure, replace the steering sensor.

    4. E226195E01
      Back Camera Position Setting:

      HINT:
      1. When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed.
      2. When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
      3. If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed.).

      1. Perform roll angle adjustment.
        1. Use switches A and B to rotate C so that it is parallel to the target adjustment bar.
      2. Perform vertical and horizontal position adjustment.
        1. Use the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      3. Select the "Next" button on the [Back Verify Mode] screen.

    5. E228127E01
      Back Verify Mode:
      1. Check that A and the target adjustment bar are overlapping.
        1. If the lines are not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.
        2. If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.
      2. Selecting "OK" will return to the [Service Menu] screen, and complete the adjustment.

        HINT:
        1. The update is not completed until "OK" is selected.
        2. When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.
        3. The adjustment values are not stored until the beep has sounded.

    6. Finish diagnostic mode.

    7. Confirm steering angle adjustment.

      HINT:
      If the steering angle has been adjusted, confirm the steering angle adjustment on the parking assist monitor screen after finishing diagnosis mode.

      1. Check on the parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.

        HINT:
        If the predicted path line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.

  3. BACK CAMERA POSITION SETTING (PROCEDURE 2)

    HINT:
    Be sure to check for DTCs before performing this procedure.


    1. Preparation for adjustment

      1. Park the vehicle with the steering wheel centered.

      2. E181012E03
        Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).

        HINT:
        Create a target bar for adjustment only when adjusting the optical axis of the camera.

        Dimension:
        Area
        Specification
        A
        824 to 834 mm (2.70 to 2.74 ft.)
        B
        1995 to 2005 mm (6.55 to 6.58 ft.)

        Text in Illustration 
        *a
        Vehicle Center
        *b
        Target Bar for Back Camera Position Setting
        *c
        Vehicle End
        *d
        Front

        HINT:
        1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-media module receiver assembly and choose a tape color which can be easily seen.
        2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
        3. Check that the back door is fully closed.

    2. Start diagnostic mode.

      NOTICE:
      The following must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.


      1. E226190
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E226193
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E252020
        Select "Next" on the [Car Information Check] screen.

      4. E233966
        Select "Back Camera Setting" on the [Mode Setting] screen.

        HINT:
        To select a grayed out item, select and hold the item for 2 seconds or more.


      5. E233967
        Select "Next" on the [Car Signal Check] screen.

        HINT:
        1. When "CHK" (red) is displayed for any items on the [Car Signal Check] screen, selecting "Next" will not change the screen to the [Back Camera Position Setting] screen.
        2. When "CHK" (red) is displayed for any items on the [Car Signal Check] screen, perform inspections using the [Car Signal Check] screen.

    3. E226195E01
      Back Camera Position Setting:

      HINT:
      1. When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
      2. If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed.).

      1. Perform roll angle adjustment.
        1. Use switches A and B to rotate C so that it is parallel to the target adjustment bar.
      2. Perform vertical and horizontal position adjustment.
        1. Use the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      3. Select the "Next" button on the [Back Verify Mode] screen.

    4. E228127E01
      Back Verify Mode:
      1. Check that A and the target adjustment bar are overlapping.
        1. If the lines are not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.
        2. If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.
      2. Selecting "OK" will return to the [Service Menu], and complete the adjustment.

        HINT:
        1. The update is not completed until "OK" is selected.
        2. When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.
        3. The adjustment values are not stored until the beep has sounded.

    5. Finish diagnostic mode.

  4. Steering Angle Setting (PROCEDURE 3)

    HINT:
    If the vehicle width extension lines and predicted path lines are not aligned when the steering wheel is centered, or if the predicted path line does not move before the steering wheel is fully turned to either the left or right, perform Steering Angle Setting.


    1. Center the steering wheel and stop the vehicle.

    2. Start diagnostic mode.

      NOTICE:
      The following must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.


      1. E226190
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E226193
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E246951
        Select "Next" on the [Car Information Check] screen.

      4. E233966
        Select "Steering Angle Setting" on the [Mode Setting] screen.

        HINT:
        To select a grayed out item, select and hold the item for 2 seconds or more.


      5. E233967
        Select "Next" on the [Car Signal Check] screen to display the [Steering Angle Setting] screen.

        HINT:
        1. When "CHK" (red) is displayed for any items on the [Car Signal Check] screen, selecting "Next" will not change the screen to the [Steering Angle Setting] screen.
        2. When "CHK" is displayed for any items on the [Car Signal Check] screen, perform inspections using the [Car Signal Check] screen.

    3. E233968
      Steering Angle Setting:
      1. Check that the steering wheel is centered (approximately +/- 5 degrees or less) and select "STEERING CENTER MEMORIZE".
      2. After the centered steering position is memorized, turn the steering wheel to the left and then to the right full lock positions and select "MAX STEERING ANGLE MEMORIZE".

        HINT:
        It is also possible to start by initially turning the steering wheel to the right side.

      3. Select "MAX STEERING ANGLE MEMORIZE" to store the steering angle adjustment value and change the screen to the [Mode Setting] screen.

        HINT:
        1. When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering angle adjustment values have been stored.
        2. The adjustment values will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected.
        3. When "Back" is selected, the screen changes to [Car Signal Check] without storing the set values.
        4. If the "Steering Angle Setting"s have not been adjusted, selecting "MAX STEERING ANGLE MEMORIZE" will not cause the adjustment values to be stored.
        5. Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment value to be stored if the steering sensor is malfunctioning.
        6. If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.

      4. Finish diagnostic mode.
      5. Confirm steering angle adjustment.

        HINT:
        If the steering angle has been adjusted, confirm the steering angle adjustment on the parking assist monitor screen after finishing diagnosis mode.
        1. Check on the parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.

          HINT:
          If the predicted path line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.


INITIALIZATION RELATED TO SIDE MONITOR SYSTEM
  1. INITIALIZE SIDE MONITOR SYSTEM

    1. When "System initializing" is displayed on the multi-display assembly, correct the steering angle neutral point using the following method.

      1. Fully turn the steering wheel to the right and left on the flat ground.

        NOTICE:
        Memorizing the steering angle neutral point must be carried out with the engine started. Apply the parking brake, depress the brake pedal, move the shift lever to P and make sure that the vehicle is not moving.

        HINT:
        "?" button is displayed at the same time as "System initializing". If the "?" button is selected, this method is displayed.


CALIBRATION RELATED TO SIDE MONITOR SYSTEM
  1. ADJUST PARKING ASSIST MONITOR SYSTEM

    1. This side monitor system can be set from the diagnostic screen of the multi-display assembly.

    2. If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

      Part Name
      Operation
      Adjustment Item
      Proceed to
      Steering sensor
      1. Removal and installation of the Steering angle sensor
      2. Removal and installation of the connector of the Steering angle sensor
      3. Replacement
      Steering angle neutral point
      -
      Steering angle setting
      -
      Multi-media module receiver assembly
      Replacement
      Vehicle contract setting
      -
      Parking assist ECU
      Replacement
      Parking assist ECU initialization
      -
      Suspension, tires, etc.
      The vehicle height changes because of suspension or tire replacement
      Rear television camera optical axis (Camera position setting)
      -
      Side television camera optical axis (Camera position setting)
      Procedure 1
      Side television camera assembly
      1. Replacement
      2. Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.
      Side television camera optical axis (Camera position setting)
      Procedure 1
      Outer rear view mirror assembly
      Replacement
      Side television camera optical axis (Camera position setting)
      Procedure 1

      NOTICE:
      After the engine switch is turned off, the multi-media module receiver assembly requires approximately 60 seconds to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      HINT:
      The adjustment values stored while performing side monitor system calibration are stored in the parking assist ECU.

  2. SIDE CAMERA SETTING (Procedure 1)

    HINT:
    Be sure to check for DTCs before performing this procedure.


    1. Preparation for adjustment

      1. Park the vehicle with the steering wheel centered.

      2. E181012E03
        Set a target bar for optical axis adjustment of the rear television camera.

        HINT:
        Only when adjusting the optical axis of the camera, create a target bar for adjustment.

        Dimension:
        Area
        Specification
        A
        825 to 835 mm (2.71 to 2.74 ft.)
        B
        1995 to 2005 mm (6.45 to 6.58 ft.)

        Text in Illustration 
        *a
        Vehicle Center
        *b
        Target Bar for Back Camera Adjustment
        *c
        Vehicle End
        *d
        Front Side

        HINT:
        1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.79 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-display assembly and choose a tape color which can be easily seen.
        2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
        3. Check that the back door is fully closed.


      3. Set a target bar for optical axis adjustment of the side television camera.

        HINT:
        Only when adjusting the optical axis of the camera, create a target bar for adjustment.


        E180069E06
        Text in Illustration 
        *A
        for LHD
        -
        -
        *a
        Target Bar for Side Camera Adjustment
        *b
        Front Wheel Axis
        *c
        Front Side
        *d
        Vehicle Center

        E180068E04

        Dimension:
        A
        B
        C
        D
        E
        F
        1183 mm
        (3.88 ft.)
        1181 mm
        (3.87 ft.)
        500 mm
        (1.64 ft.)
        500 mm
        (1.64 ft.)
        500 mm
        (1.64 ft.)
        180 mm
        (7.09 in.)

        Text in Illustration 
        *A
        for RHD
        -
        -
        *a
        Target Bar for Side Camera Adjustment
        *b
        Front Wheel Axis
        *c
        Front Side
        *d
        Vehicle Center

        HINT:
        Target bars for side camera adjustment should be made with 2 pieces of 2.5 cm wide tape; one piece should be 100 cm (3.28 ft.) (C+D) and the other should be 68 cm (2.23 ft.) (E+F) long. Check the tape color on the multi-media module receiver assembly and choose a tape color which can be easily seen.

    2. Start diagnostic mode.

      NOTICE:
      Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

      HINT:
      The displayed items may differ depending on vehicle specifications.


      1. E248980
        Select "Function Check/Setting" on the [Service Menu] screen.

      2. E248981
        Select "Camera Setting" on the [Function Check/Setting] screen.

      3. E246954
        Select "Side Camera Setting" on the [Mode Setting] screen.

        HINT:
        To select a grayed out item, select and hold the item for 2 seconds or more.


      4. E252019
        Select "Next" on the [Signal Check] screen.

        NOTICE:
        1. When "CHK" (red) is displayed for any items on the [Signal Check] screen, selecting "Next" will not change the screen to the [Side Camera Position Setting] screen.
        2. When "CHK" (red) is displayed for any items on the [Signal Check] screen, perform inspections using the [Signal Check] screen.

        HINT:
        1. When the outer mirrors are retracted, selecting "Next" will not change the screen to the [Side Camera Position Setting] screen.
        2. If the screen does not change to the [Side Camera Position Setting] screen even though the outer mirrors are extended, perform the "MIRROR SW" check on the [Signal Check] screen.
        3. If the screen does not change to the [Side Camera Position Setting] screen even after "OK" (blue) is displayed as a result of the MIRROR SW check on the [Signal Check] screen, replace the parking assist ECU.

    3. E181004E02
      Side Camera Position Setting:

      HINT:
      Colors used on the [Side Camera Position Setting] screen

      Text in Illustration 
      *a
      Target Adjustment Bar for Side Camera Position Setting
      *b
      Red Frame
      *c
      Yellow Frame

      1. E246955E02
        Perform the roll angle adjustment.
        1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      2. Perform the vertical and horizontal position adjustment.
        1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      3. Select "Next" to display [Side Verify Mode].

    4. Side Verify Mode:


      1. E246956
        Check that the red cross and the target adjustment bar are aligned.

        HINT:
        If they are not aligned, select "Back" and perform [Side Camera Position Setting] again.

      2. Select "Next" to display [Side Camera Signal Check].

    5. Side Camera Signal Check:


      1. E248973E01
        Select "OK" to store the side camera aiming adjustment value and change the screen to the [Service Menu] screen.

        HINT:
        1. When "OK" is selected, a beep will sound to confirm that the side camera aiming adjustment values have been stored.
        2. The adjustment value will not be stored unless "Back" is selected.

    6. Finish diagnostic mode.


REGISTRATION RELATED TO WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)
  1. DESCRIPTION OF CODE REGISTRATION

    HINT:
    1. Recognition code registration is necessary when replacing the door control transmitter or door control receiver.
    2. Add mode is used to register new recognition codes while still retaining codes already registered. This mode is used when a new transmitter is added. If the number of registered codes exceeds 6, the previously registered codes will be cleared in order, starting from the first registered code.
    3. Rewrite mode is used to clear all the previously registered recognition codes in order to register new recognition codes. This mode is used when the transmitter or door control receiver is replaced with a new one.
    4. Confirmation mode is used to confirm how many recognition codes have already been registered before registering any additional recognition codes.
    5. Prohibition mode is used to clear all the registered codes and disables the wireless door lock function. This mode is used when the transmitter is lost.*
      1. *: The system can be manually switched to prohibition mode (for Middle East).
    6. The registration procedures must be performed in order.

  2. REGISTER RECOGNITION CODE (USING INTELLIGENT TESTER)

    HINT:
    For detailed procedures, refer to the prompts on the intelligent tester screen. The number of currently registered codes can be checked on the first screen of Wireless Code Registration.


    1. Turn the ignition switch to ON.

    2. Enter the following menus: Body / Main Body / Utility / Wireless Code Registration.

    3. Press both the lock and unlock switches at the same time for 1 to 1.5 seconds.

    4. Press either switch for more than 1 second within 3 seconds.

    5. Check the response to the registration completion.
      B111915E20

      HINT:
      1. If the lock-unlock operation occurs twice, the registration of the recognition code has failed. Perform the registration procedures again from the beginning.
      2. If registering another transmitter, repeat the procedures after the intelligent tester operation. All 6 recognition codes can be registered consecutively.

    6. Perform either of the following to complete the registration of the recognition codes:

      1. Use the intelligent tester to send a completion command.
      2. Disconnect the intelligent tester.

  3. REGISTER RECOGNITION CODE (USING SWITCH OPERATION)

    1. Make sure the following conditions are met.

      1. No key is inserted in the ignition key cylinder.
      2. The driver side door is open (the other doors are closed).
      3. The driver side door is unlocked.

    2. Insert and remove the key into/from the ignition key cylinder twice (Insert → Remove → Insert → Remove) within 5 seconds.

      HINT:
      The procedure should end with the key removed.

    3. Perform the following operations within 40 seconds.

      1. Close and open the driver side door twice (Close → Open → Close → Open).

        HINT:
        The procedure should end with the door open.

      2. Insert and remove the key into/from the ignition key cylinder (Insert → Remove).

        HINT:
        The procedure should end with the key removed.

      3. Close and open the driver side door twice (Close → Open → Close → Open).

        HINT:
        The procedure should end with the door open.

      4. Insert the key into the ignition key cylinder and close all the doors.

  4. Perform the following operations within 40 seconds.

    1. Turn the ignition switch to ON and then off at approximately 1 second intervals. Operate the ignition switch according to the number of times shown below.
      B111914E17

      HINT:
      If the number of ignition switch ON - off operations is 0, 4, or 6 or more, there will be no response (power door lock and unlock operation) to show which mode has been selected.

    2. Remove the key from the ignition key cylinder.

  5. Check that the response begins within 5 seconds after completing the above step, and that the response matches the selected mode.
    B222617E02

    NOTICE:
    After the system has been set to prohibition mode, enter confirmation mode and check that the number of registered keys is 0.

    HINT:
    1. In confirmation mode, the lock-unlock operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, the lock-unlock operation will occur twice.
    2. In confirmation mode, if no recognition codes have been registered, the lock-unlock operation will occur 11 times.
    3. If confirmation mode or prohibition mode is selected, the operation ends after the response to the selected mode completes.

  6. If add mode or rewrite mode is selected, perform the following procedures.

    1. Press a single switch (lock or unlock) within 5 seconds.

    2. Check that the response begins within 3 seconds after completing the above step, and that the response indicates that registration has been completed correctly.
      B111915E21

      HINT:
      1. If the lock-unlock operation occurs twice, the registration of the recognition code has failed. Perform the registration procedures again from the beginning.
      2. If registering another transmitter, repeat the procedures after the mode selection response confirmation. All 6 recognition codes can be registered consecutively.

    3. Perform either of the following to complete the registration of the recognition codes:

      1. Open a door.
      2. Insert the key into the ignition key cylinder.


INITIALIZATION RELATED TO POWER WINDOW CONTROL SYSTEM (Models with Jam Protection Function on 4 Windows)
  1. INITIALIZE POWER WINDOW CONTROL SYSTEM (POWER WINDOW REGULATOR MOTOR (ALL DOORS))

    CAUTION:
    When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized. Functions such as the auto up/down, jam protection and key-off do not operate if the initialization is not performed.

    HINT:
    When the battery is replaced, it is not necessary to initialize the power window regulator motor.

    NOTICE:
    1. When the power window regulator motor is replaced, DTC B2313 is output. Clear the DTC after the initialization.
    2. When performing initialization, do not perform any other procedures.
    3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used, due to detection of a value different from the operation learned value of the door glass movement speed. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
      1. Open the power window by fully pushing down the power window switch.
      2. Close the power window by fully pulling up the power window switch and holding it at the auto up position.
    4. If the initialization is not completed properly, the LIN communication system may have a malfunction.


    1. Initialization procedures when replacing the power window regulator motor with a new one:

      1. Connect the battery and turn the engine switch on (IG) (at this time, the LED on the power window switch blinks to indicate that it is ready for initialization).
      2. Fully open the window by fully pushing the power window switch, and hold the switch for 1 second or more after the window is fully opened.
      3. Fully close the power window by fully pulling the power window switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position. The LED on the power window switch stops blinking and illuminates to indicate that the initialization is complete.

    2. Initialization procedures when removing/installing the power window regulator motor:

      1. Connect the battery and turn the engine switch on (IG).
      2. Fully close the power window by fully pulling the power window switch, and hold the switch for 6 seconds or more after the window is fully closed (if the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again).
      3. Fully open the window by pushing down the power window switch, and hold the switch for 1 second or more after the window is fully opened.
      4. Release the power window switch. Then fully push and hold the switch for 4 seconds or more.
      5. Fully close the power window by fully pulling the power window switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position and complete the initialization.

    3. Initialization procedures when the power window does not fully open:

      1. Connect the battery and turn the engine switch on (IG).
      2. Fully close the power window by fully pulling the power window switch, and hold the switch for 6 seconds or more after the window is fully closed (if the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again).
      3. Fully open the window by pushing down the power window switch, and hold the switch for 1 second or more after the window is fully opened.
      4. Release the power window switch. Then fully push and hold the switch 4 seconds or more.
      5. Fully close the power window by fully pulling the power window switch, and hold the switch 1 second or more after the window is fully closed to reset the glass position and complete the initialization.


INITIALIZATION RELATED TO AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
  1. INITIALIZATION SERVO MOTOR

    1. Turn the engine switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the engine switch on (IG).

    4. Press the blower OFF switch.

    5. Turn the intelligent tester on.

    6. Enter the following menus: Body Electrical / Air Conditioner / Utility / Servomotor Initialization.

    7. According to the intelligent tester display, perform servomotor initialization.

      HINT:
      During initialization, the AUTO indicator light comes on, and then goes off when initialization has finished.

    8. According to the intelligent tester display, select the "Exit" switch to finish initialization.


INITIALIZATION RELATED TO POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Driver Door Window Only)
  1. INITIALIZE POWER WINDOW CONTROL SYSTEM (POWER WINDOW REGULATOR MOTOR (for Driver Side))

    CAUTION:
    When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized. Functions such as the auto up/down, jam protection and key-off do not operate if the initialization is not performed.

    HINT:
    When the battery is replaced, it is not necessary to initialize the power window regulator motor.

    NOTICE:
    1. When the power window regulator motor is replaced, DTC B2313 is output. Clear the DTC after the initialization.
    2. When performing initialization, do not perform any other procedures.
    3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used, due to detection of a value different from the operation learned value of the door glass movement speed. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
      1. Open the power window by fully pushing down the power window switch.
      2. Close the power window by fully pulling up the power window switch and holding it at the auto up position.
    4. If the initialization is not completed properly, the LIN communication system may have a malfunction.


    1. Initialization procedures when replacing the power window regulator motor with a new one:

      1. Connect the battery and turn the ignition switch ON (at this time, the LED on the power window switch blinks to indicate that it is ready for initialization).
      2. Fully open the window by fully pushing the power window switch, and hold the switch for 1 second or more after the window is fully opened.
      3. Fully close the power window by fully pulling the power window switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position. The LED on the power window switch stops blinking and illuminated to indicate that the initialization is complete.

    2. Initialization procedures when removing/installing the power window regulator motor:

      1. Connect the battery and turn the ignition switch ON.
      2. Fully close the power window by fully pulling the power window switch, and hold the switch for 6 seconds or more after the window is fully closed (if the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again).
      3. Fully open the window by pushing down the power window switch, and hold the switch for 1 second or more after the window is fully opened.
      4. Release the power window switch. Then fully push and hold the switch for 4 seconds or more.
      5. Fully close the power window by fully pulling the power window switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position and complete the initialization.

    3. Initialization procedures when the power window does not fully open:

      1. Connect the battery and turn the ignition switch ON.
      2. Fully close the power window by fully pulling the power window switch, and hold the switch for 6 seconds or more after the window is fully closed (if the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again).
      3. Fully open the window by pushing down the power window switch, and hold the switch for 1 second or more after the window is fully opened.
      4. Release the power window switch. Then fully push and hold the switch 4 seconds or more.
      5. Fully close the power window by fully pulling the power window switch, and hold the switch 1 second or more after the window is fully closed to reset the glass position and complete the initialization.


INITIALIZATION RELATED TO INNER REAR VIEW MIRROR
  1. SELECT COMPASS DISPLAY MODE

    1. The compass switch allows you to select the Display or Non-display mode of the compass.

  2. SET ZONE

    1. Deviation between the "magnetic north" and "actual north" differs depending on the location. Therefore, adjustment of the magnetism is required. Because the magnetic condition differs depending on the area where the vehicle is used, it is necessary for each user to set the zone (refer to Compass Zone Map). The zone setting can be changed using the compass switch of the inner mirror.

  3. PERFORM CALIBRATION

    1. Because each vehicle has its own magnetic field, calibration should be performed for each individual vehicle. This compass function is used when storing the record of the vehicle's magnetic field.

  4. WHEN COMPASS IS MAGNETIZED

    1. The compass could be magnetized during shipping by vessels or freight cars. Therefore, ensure that calibration is performed properly before delivery. If driving the vehicle in a circle several times does not complete the calibration procedure, there may be a compass magnetization problem.
      B251093E01

  5. Deviation Calibration Procedure

    1. B219621
      Turn the ignition switch to the "IG-ON" position and push and hold the "AUTO" switch for 6 seconds until the zone number appears on the display.

      HINT:
      Pushing the "AUTO" switch for 3 seconds turns on or off the compass display.

    2. Push the "AUTO" switch to select the number of the zone where the vehicle is located. See the map for zone reference.
      B231508

  6. Circling Calibration Procedure

    1. B141149
      Start the engine and push and hold the "AUTO" switch for 9 seconds until "C" appears on the display.

    2. C180413
      Drive the vehicle slowly at 8 km/h (5 mph) or lower in a circle. If there is not enough space to drive in a circle, turn the car around in the following manner, doing two three-point turns in succession. After driving in 1 to 3 circles in the above method, calibration is completed with the direction is shown on the display.

      HINT:
      1. Do not perform calibration of the compass in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
      2. During calibration, do not operate electric systems (sliding roof, power windows, etc.) as they may interfere with the calibration.


INITIALIZATION RELATED TO SLIDING ROOF SYSTEM
  1. INITIALIZE SLIDING ROOF DRIVE GEAR

    NOTICE:
    1. When the sliding roof glass is replaced or removed and installed, or the drive gear assembly is replaced, the sliding roof drive gear requires initialization (pulse sensor initial position setting), as the glass position cannot be determined. If initialization is not performed, the auto slide open and close/tilt up and down function may not operate, or the sliding roof may move in reverse or become misaligned.
    2. During initialization, do not apply a physical shock, such as opening/closing a door or driving the vehicle at 5 km/h (3.10 mph) or more, to the vehicle and do not perform the following electrical operations:
      1. Cranking the engine
      2. Turning the engine switch from on (IG) to off
      3. Operating the power window switches
      4. Operating the window defogger switch
      5. Operating the blower switch
      6. Locking/Unlocking the door
      7. Operating the headlight dimmer switch

    HINT:
    When the cable is disconnected and reconnected to the negative (-) battery terminal or the drive gear connector is disconnected and reconnected, the sliding roof drive gear (pulse sensor initial position setting) initialization is not necessary.


    1. Perform initialization according to the table below.

      Condition of Sliding Roof
      Proceed to
      Auto slide open and close/tilt up and down function does not operate
      Procedure A
      Sliding roof moves in reverse direction during tilt down operation
      Procedure B
      Sliding roof moves in reverse direction during slide close operation
      Procedure C
      1. Procedure A
        1. Turn the engine switch to ON.
        2. Open the sliding roof to the fully tilt up position.
        3. Press and hold the UP switch to perform the following operations: tilt up → approximately 10 second pause → tilt down → slide open → slide close.

          NOTICE:
          Make sure not to release the switch during the initialization. If the switch is released, perform the initialization again.

        4. Continue to hold the switch for 1 second or more after the sliding roof stops in the fully closed position, and then release it.
        5. The initialization is completed.
      2. Procedure B
        1. Turn the engine switch to ON.
        2. Press the UP switch until the sliding roof stops.

          HINT:
          If the glass becomes misaligned or does not fully tilt up, perform the following operations:
          1. Operate the CLOSE switch until the sliding roof stops moving.
          2. Operate the UP switch until the sliding roof stops moving, then proceed to the next step.

        3. Release the switch.
        4. Press and hold the UP switch to perform the following operations: tilt up → approximately 10 second pause → tilt down → slide open → slide close.

          NOTICE:
          Make sure not to release the switch during the initialization. If the switch is released, perform the initialization again.

        5. Continue to hold the switch for 1 second or more after the sliding roof stops in the fully closed position, and then release it.
        6. The initialization is completed.
      3. Procedure C
        1. Turn the engine switch to ON.
        2. Press and hold the CLOSE switch to perform the following operations: slide close → move in reverse direction → 10 second pause → slide close → tilt up → tilt down.

          NOTICE:
          Make sure not to release the switch during the initialization. If the switch is released, perform the initialization again.

        3. Continue to hold the switch for 1 second or more after the sliding roof stops in the fully closed position, and then release it.
        4. Check if the auto function is operative.


INITIALIZATION RELATED TO POWER BACK DOOR SYSTEM
  1. RESET BACK DOOR CLOSE POSITION

    NOTICE:
    Perform initialization of the power back door system (power back door unit assembly [power back door ECU] initialization) if one of the following is performed: 1) The cable is disconnected from the negative (-) battery terminal; 2) a wire harness, the power back door unit assembly (power back door ECU) or back door lock assembly is replaced or removed/installed; or 3) the ECU-B2 fuse is replaced or removed/installed. If initialization is not performed, the power back door system will not operate.


    1. When the back door is open and the cable is disconnected and reconnected to the negative (-) battery terminal, fully close the back door by hand.

      HINT:
      Initialization is not necessary if the cable is disconnected and reconnected to the negative (-) battery terminal while the back door is closed. However, because the power back door unit assembly [power back door ECU] recognizes that the back door is locked, the power back door system will not operate if the back door is not unlocked.

  2. CHECK POWER BACK DOOR FUNCTION

    HINT:
    1. Proceed to Operation Check.
    2. If the power back door system does not operate and/or the back door does not open, disconnect the cable from the negative (-) battery terminal. Then wait 10 seconds, reconnect the cable and perform initialization of the power back door system again.


INITIALIZATION RELATED TO LIGHTING SYSTEM
  1. HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION (except w/ Active Height Control Suspension)

    1. *1: w/ Static Headlight Auto Leveling
    2. *2: w/ Dynamic Headlight Auto Leveling

    NOTICE:
    1. Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor LH.
    2. Initialization is also necessary when the headlight leveling ECU*1 or headlight swivel ECU*2 is replaced.
    3. Adjust the headlight aim after initializing the headlight leveling ECU*1 or headlight swivel ECU*2.
    1. When a malfunction is detected in the automatic headlight beam level control system, the height control sensor signal initialization is impossible. Perform troubleshooting before initialization.


    1. PREPARE VEHICLE FOR INITIALIZATION (Procedure A)

      1. Unload the trunk and vehicle, and make sure that the spare tire, tools and jack are in their original positions.
      2. Check that there are no occupants in the vehicle.
      3. Turn off the headlights.
      4. Stop the vehicle on a level surface and keep the vehicle height unchanged.
      5. Go to procedure B

    2. CHECK WARNING LIGHT (Procedure B)

      1. Turn the ignition switch to ON and check the headlight beam level control system warning light.

        OK:
        Condition
        Specified Condition
        The headlight leveling ECU*1 or headlight swivel ECU*2 is replaced with a new one.
        Warning light continuously blinks 6 times at 2 Hz.
        Removal and reinstallation of the headlight leveling ECU*1 or headlight swivel ECU*2, replacement of the rear height control sensor LH*3, removal and reinstallation of the rear height control sensor LH, replacement of the suspension, etc.
        Warning light comes on for approximately 3 seconds, and then turns off (bulb check function).

        *1: w/ Static Headlight Auto Leveling
        *2: w/ Dynamic Headlight Auto Leveling

        HINT:
        If the warning light does not come on when turning the ignition switch to ON, perform inspections and repairs according to "Problem Symptoms Table.

        Result 
        Result
        Proceed to
        OK
        Procedure C
        NG
        See procedure LIGHTING (EXT) / LIGHTING SYSTEM / PROBLEM SYMPTOMS TABLE

    3. INITIALIZATION (Procedure C)

      SST
      09843-18040  

      1. C166029E38
        Connect terminals 4 (CG) and 8 (LVL) of the DLC3 using SST.
        Text in Illustration 
        *a
        Front view of DLC3

      2. E244505E01
        Turn the low beam headlights on and off using the light control switch within 20 seconds after connecting the terminals.

        HINT:
        The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.

        Fuel Level
        Number of Times to Turn Low Beam Headlights on and off
        Fuel level is within range A.
        1
        Fuel level is within range B.
        2
        Fuel level is within range C.
        3
        Fuel level is within range D.
        4
        Fuel level is within range E.
        5

        NOTICE:
        1. Turn the low beam headlights on and off at approximately 3-second intervals.
        2. Be sure to operate the headlight dimmer switch from the outside of the vehicle.

      3. Check the warning light.

        OK:
        Condition
        Specified Condition
        The headlight leveling ECU*1 or headlight swivel ECU*2 is replaced with a new one.
        Blinks 6 times at 2 Hz → Blinks N* times at 2 Hz, and then turns off.
        Removal and reinstallation of the headlight leveling ECU*1 or headlight swivel ECU*2, replacement of the rear height control sensor LH, removal and reinstallation of the rear height control sensor LH, replacement of the suspension, etc.
        Off → Blinks N* times at 2 Hz, and then turns off.

        *1: w/ Static Headlight Auto Leveling
        *2: w/ Dynamic Headlight Auto Leveling

        HINT:
        1. *: The number of times that the indicator blinks is determined by the number of times the low beam headlights are turned on and off.
        2. If the calculated vehicle height is not within the acceptable range, the rear height control sensor initialization will end as an abnormal termination, and the warning indicator will blink 6 times at 2 Hz continuously. Disconnect SST from the DLC3 and turn the ignition switch off. Then restart from "Check Warning Light".
        3. If initialization cannot be finished normally, perform inspections and repairs according to "Problem Symptoms Table".

        Result 
        Result
        Proceed to
        OK
        END
        NG
        See procedure LIGHTING (EXT) / LIGHTING SYSTEM / HOW TO PROCEED WITH TROUBLESHOOTING


ADJUSTMENT FOR HEADLIGHT ASSEMBLY (for Halogen Headlight)

HINT:
It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment procedure.

  1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT

    1. Prepare the vehicle:

      1. Make sure that there is no damage to the body around the headlights.
      2. Fill the fuel tank.
      3. Make sure that the oil is filled to the specified level.
      4. Make sure that the coolant is filled to the specified level.
      5. Inflate the tires to the appropriate pressure.
      6. Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.
      7. Have a person of average weight (75 kg, 165 lb) sit in the driver seat.
      8. Vehicles with height adjustable suspension should have the vehicle height set to the lowest setting prior to adjusting the headlight aim.
      9. Vehicles with manually adjustable headlights should be adjusted to "0" (w/ headlight leveling switch).

  2. PREPARATION FOR HEADLIGHT AIMING (Using a screen)

    1. E248183E02
      Prepare the vehicle:
      Text in Illustration 
      *a
      90°
      *b
      25 m or 3 m
      1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
      2. Place the vehicle at a 90° angle to the wall.
      3. Create a 25 m (82 ft.) distance between the vehicle (headlight bulb center) and the wall.
      4. Make sure that the vehicle is on a level surface.
      5. Bounce the vehicle up and down to settle the suspension.

        NOTICE:
        A distance of 25 m (82 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).

    2. Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.

    3. Draw a vertical line down the center of the screen (V line).

    4. Set the screen as shown in the illustration.

      HINT:
      1. Stand the screen perpendicular to the ground.
      2. Align the V line on the screen with the center of the vehicle.
      E248184E03

    5. E257183E01
      Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
      Text in Illustration 
      *a
      V LH Line
      *b
      V Line
      *c
      V RH Line
      *d
      H Line
      *e
      Ground

      HINT:
      1. The base lines differ for "low beam inspection" and "high beam inspection".
      2. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.

      1. H Line (Headlight height):
        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.
      2. V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):
        Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).

  3. INSPECT HEADLIGHT AIMING

    1. E248183E01
      Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.
      Text in Illustration 
      *a
      25 m or 3 m (82 ft. or 9.84 ft.)

      NOTICE:
      Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

      HINT:
      When checking the aim of the high beam headlight, cover the low beam headlight or disconnect the connector.

    2. Start the engine.

    3. Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

      HINT:
      1. Since the low beam and high beam headlight on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
      2. The illustration is for LHD vehicles. RHD vehicles are the opposite of the illustration.
      3. If the alignment distance is 25 m (82 ft.):
        The low beam cutoff line should be within 83 mm (3.27 in.) and 375 mm (14.8 in.) below the H line as well as 249 mm (9.80 in.) left or right of the V LH or V RH line.
      4. If the alignment distance is 3 m (9.84 ft.):
        The low beam cutoff line should be within 10 mm (0.394 in.) and 45 mm (1.77 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.
      5. If the alignment distance is 25 m (82 ft.):
        The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

      6. If the alignment distance is 3 m (9.84 ft.):
        The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

        E231280E04

    4. Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

      HINT:
      1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
      2. If the alignment distance is 25 m (82.0 ft.):
        The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

      3. If the alignment distance is 3 m (9.84 ft.):
        The high beam center of intensity should be within 21 mm (0.82 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

        E261529E01

  4. ADJUSTMENT HEADLIGHT AIMING

    1. Headlight low beam.


      1. Using a screwdriver, adjust the aim.

        E251166E02
        Text in Illustration 
        *A
        w/ Projector
        *B
        w/o Projector
        *1
        Vertical Aiming Screw
        *2
        Horizontal Aiming Screw
        *3
        Screwdriver
        -
        -
        Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.

        NOTICE:
        The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

        HINT:
        1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
        2. When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.
        3. If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.
        4. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.
        5. Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.

    2. Headlight high beam.


      1. Using a screwdriver, adjust the aim.

        E250281E03
        Text in Illustration 
        *A
        w/ Projector
        *B
        w/o Projector
        *1
        Vertical Aiming Screw
        *2
        Horizontal Aiming Screw
        *3
        Screwdriver
        -
        -
        Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

        NOTICE:
        The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

        HINT:
        1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
        2. When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.
        3. If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.
        4. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.
        5. Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.


ADJUSTMENT FOR HEADLIGHT ASSEMBLY (for HID Headlight)

HINT:
It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment procedure.

  1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT

    1. Prepare the vehicle:

      1. Make sure that there is no damage to the body around the headlights.
      2. Fill the fuel tank.
      3. Make sure that the oil is filled to the specified level.
      4. Make sure that the coolant is filled to the specified level.
      5. Inflate the tires to the appropriate pressure.
      6. Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.
      7. Have a person of average weight (75 kg, 165 lb) sit in the driver seat.
      8. Vehicles with height adjustable suspension should have the vehicle height set to the lowest setting prior to adjusting the headlight aim (w/ Active Height Control).
      9. Vehicles with manually adjustable headlights should be adjusted to "0" (w/ Headlight Leveling Switch).

  2. PREPARATION FOR HEADLIGHT AIMING (Using a screen)

    1. E248183E02
      except China, Indonesia:
      Prepare the vehicle.
      Text in Illustration 
      *a
      90°
      *b
      25 m or 3 m
      1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
      2. Place the vehicle at a 90° angle to the wall.
      3. Create a 10 m (32.8 ft) distance between the vehicle (fog light bulb center) and the wall.
      4. Make sure that the vehicle is on a level surface.
      5. Bounce the vehicle up and down to settle the suspension.

        NOTICE:
        A distance of 10 m (32.8 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).

    2. E248183E02
      for China, Indonesia:
      Prepare the vehicle.
      Text in Illustration 
      *a
      90°
      *b
      10 m or 3 m
      1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
      2. Place the vehicle at a 90° angle to the wall.
      3. Create a 25 m (82 ft.) distance between the vehicle (headlight bulb center) and the wall.
      4. Make sure that the vehicle is on a level surface.
      5. Bounce the vehicle up and down to settle the suspension.

        NOTICE:
        A distance of 25 m (82 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).

    3. Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.

    4. Draw a vertical line down the center of the screen (V line).

    5. except China, Indonesia:
      Set the screen as shown in the illustration.

      HINT:
      1. Stand the screen perpendicular to the ground.

      2. Align the V line on the screen with the center of the vehicle.

        E248184E03

    6. for China, Indonesia:
      Set the screen as shown in the illustration.

      HINT:
      1. Stand the screen perpendicular to the ground.

      2. Align the V line on the screen with the center of the vehicle.

        E248184E05

    7. E257183E01
      Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
      Text in Illustration 
      *a
      V LH Line
      *b
      V Line
      *c
      V RH Line
      *d
      H Line
      *e
      Ground

      HINT:
      1. The base lines differ for "low beam inspection" and "high beam inspection".
      2. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.

      1. H Line (Headlight height):
        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.
      2. V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):
        Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).

  3. INSPECT HEADLIGHT AIMING

    1. Cover the headlight or disconnect the connector of the headlight/headlight ECU on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.

      NOTICE:
      Do not disconnect the HID high voltage connector for the bulb when performing this aiming inspection.

      NOTICE:
      Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

      HINT:
      When checking the aim of the high beam headlight, cover the low beam headlight or disconnect the connector.

    2. Start the engine.

    3. except China, Indonesia:
      Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

      HINT:
      1. Since the low beam and high beam headlight on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
      2. The illustration is for LHD vehicles. RHD vehicles are the opposite of the illustration.
      3. If the alignment distance is 25 m (82 ft.):
        The low beam cutoff line should be within 6 mm (0.23 in.) and 84 mm (3.30 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.
      4. If the alignment distance is 25 m (82 ft.):
        The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

      5. If the alignment distance is 3 m (9.84 ft.):
        The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

        E231280E04

    4. for China:
      Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

      HINT:
      1. Since the low beam and high beam headlight on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
      2. If the alignment distance is 10 m (32.8 ft.):
        The low beam cutoff line should be within 94 mm (3.70 in.) and 285 mm (11.2 in.) below the H line as well as 99 mm (3.89 in.) left or right of the V LH or V RH line.
      3. If the alignment distance is 3 m (9.84 ft.):
        The low beam cutoff line should be within 28 mm (1.10 in.) and 85 mm (3.34 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.
      4. If the alignment distance is 10 m (32.8 ft.):
        The horizontal line of the preferred low beam cutoff line is 189 mm (7.44 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

      5. If the alignment distance is 3 m (9.84 ft.):
        The horizontal line of the preferred low beam cutoff line is 57 mm (2.24 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

        E231280E05

    5. for Indonesia:
      Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

      HINT:
      1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
      2. If the alignment distance is 10 m (32.8 ft.):
        The low beam cutoff line should be within 33 mm (1.30 in.) and 150 mm (5.91 in.) below the H line as well as 66 mm (2.60 in.) left or right of the V LH or V RH line.
      3. If the alignment distance is 3 m (9.84 ft.):
        The low beam cutoff line should be within 10 mm (0.394 in.) and 45 mm (1.77 in.) below the H line as well as 20 mm (0.787 in.) left or right of the V LH or V RH line.
      4. If the alignment distance is 10 m (32.8 ft.):
        The horizontal line of the preferred low beam cutoff line is 99 mm (3.90 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

      5. If the alignment distance is 3 m (9.84 ft.):
        The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

        E261772E02

  4. except China, Indonesia:
    Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

    HINT:
    1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
    2. If the alignment distance is 25 m (82.0 ft.):
      The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

    3. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity should be within 21 mm (0.827 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

      E261529E01

  5. for China:
    Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

    HINT:
    1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
    2. If the alignment distance is 10 m (32.8 ft.):
      The high beam center of intensity should be within 47 mm (1.85 in.) below the H line.
    3. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity should be within 14 mm (0.55 in.) below the H line.
    4. If the alignment distance is 10 m (32.8 ft.):
      The high beam center of intensity for the headlight assembly LH should be within 169 mm (6.65 in.) left and 349 mm (1.14 ft.) right of the V LH line.
    5. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity for the headlight assembly LH should be within 51 mm (2.0 in.) left and 105 mm (4.13 in.) right of the V LH line.
    6. If the alignment distance is 10 m (32.8 ft.):
      The high beam center of intensity for the headlight assembly RH should be within 349 mm (1.14 ft.) left or right of the V RH line.

    7. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity for the headlight assembly RH should be within 105 mm (4.13 in.) left or right of the V RH line.

      E261530E03

  6. for Indonesia:
    Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

    HINT:
    1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
    2. If the alignment distance is 10 m (32.8 ft.):
      The high beam center of intensity should be within 70 mm (2.76 in.) above and 99 mm (3.90 in.) below the H line as well as 199 mm (7.83 ft.) left or right of the V LH or V RH line.

    3. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity should be within 21 mm (0.827 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

      E261529E02

  7. ADJUSTMENT HEADLIGHT AIMING

    1. Headlight low beam.


      1. Using a screwdriver, adjust the aim.

        E251168E03
        Text in Illustration 
        *A
        Type 1
        *B
        Type 2
        *1
        Vertical Aiming Screw
        *2
        Horizontal Aiming Screw
        *3
        Screwdriver
        -
        -
        Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

        NOTICE:
        The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

        HINT:
        1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
        2. When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.
        3. If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.
        4. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.
        5. Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.

    2. Headlight high beam.


      1. Using a screwdriver, adjust the aim.

        E251167E03
        Text in Illustration 
        *A
        Type 1
        *B
        Type 2
        *1
        Vertical Aiming Screw
        *2
        Horizontal Aiming Screw
        *3
        Screwdriver
        -
        -
        Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

        NOTICE:
        The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

        HINT:
        1. Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
        2. When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.
        3. If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.
        4. The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.
        5. Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.


ADJUSTMENT FOR FOG LIGHT ASSEMBLY

HINT:
If there is a problem with the fog light aim, the cause of the problem may be an incorrectly installed bulb. Therefore, bulb installation should be checked prior to performing the adjustment procedure.

  1. VEHICLE PREPARATION FOR FOG LIGHT AIMING ADJUSTMENT

    1. Prepare the vehicle:

      1. Make sure that there is no damage to or deformation of the body around the fog lights.
      2. Fill the fuel tank.
      3. Make sure that the oil is filled to the specified level.
      4. Make sure that the coolant is filled to the specified level.
      5. Inflate the tires to the appropriate pressure
      6. Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.
      7. Have a person of average weight (75 kg, 165 lb) sit in the driver's seat.
      8. Vehicles with height adjustable suspension should have the vehicle height sit to the lowest setting prior to adjusting the fog light aim.

  2. PREPARATION FOR FOG LIGHT AIMING

    1. E250282E02
      except China, Indonesia:
      Prepare the vehicle.
      Text in Illustration 
      *a
      90°
      *b
      25 m or 3 m
      1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
      2. Place the vehicle at a 90° angle to the wall.
      3. Create a 25 m (82 ft.) distance between the vehicle (fog light bulb center) and the wall.
      4. Make sure that the vehicle is on a level surface.
      5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 25 m (82 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).

    2. E250282E02
      for China, Indonesia:
      Prepare the vehicle.
      Text in Illustration 
      *a
      90°
      *b
      10 m or 3 m
      1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
      2. Place the vehicle at a 90° angle to the wall.
      3. Create a 10 m (32.8 ft) distance between the vehicle (fog light bulb center) and the wall.
      4. Make sure that the vehicle is on a level surface.
      5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 10 m (32.8 ft) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If unavailable to secure a distance of exactly 3 m (9.84 ft) to check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration.)

    3. Prepare a piece of thick white paper approximately 2.0 m (6.56 ft.) (height) x 4.0 m (13.1 ft.) (width) to use as a screen.

    4. Draw a vertical line down the center of the screen (V line).

    5. except China, Indonesia:
      Set the screen as shown in the illustration.

      HINT:
      1. Stand the screen perpendicular to the ground.

      2. Align the V line on the screen with the center of the vehicle.

        E250284E01

    6. for China, Indonesia:
      Set the screen as shown in the illustration.

      HINT:
      1. Stand the screen perpendicular to the ground.

      2. Align the V line on the screen with the center of the vehicle.

        E250284E04

    7. E257183E01
      Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
      Text in Illustration 
      *a
      V LH Line
      *b
      V Line
      *c
      V RH Line
      *d
      H Line
      *e
      Ground

      HINT:
      Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.

      1. H line (Fog light height):
        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
      2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
        Draw two vertical lines so that they intersect the H line at each center mark.

  3. INSPECT FOG LIGHT AIMING

    1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

      NOTICE:
      Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

    2. Start the engine

    3. except China, Indonesia:
      Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

      HINT:
      1. If the alignment distance is 25 m (82 ft.):
        The upper edge of the hot zone for the fog light should be 375 mm (1.48 in.) below the H line.
      2. If the alignment distance is 3 m (9.84 ft.):
        The upper edge of the hot zone for the fog light should be 45 mm (1.77 in.) below the H line.

      E264604E01

  4. for China, Indonesia:
    Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

    HINT:
    1. If the alignment distance is 10 m (32.8 ft.):
      The upper edge of the hot zone for the fog light should be 150 mm (5.91 in.) below the H line.
    2. If the alignment distance is 3 m (9.84 ft.):
      The upper edge of the hot zone for the fog light should be 45 mm (1.77 in.) below the H line.
    E264604E03

  5. ADJUSTMENT FOG LIGHT AIMING

    1. E244779E02
      Adjust the aim vertically:
      Adjust the aim of each fog light so that it is within the specified range by turning the aiming screw with a screwdriver.
      Text in Illustration 
      *1
      Aiming screw

      NOTICE:
      The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

      HINT:
      If it is not possible to correctly adjust fog light aim, check the bulb, fog light unit, and fog light unit reflector installation.

← INITIALIZATION (Sep 2011 – Dec 2011)GENERAL INFORMATION (from Sep 2011) →