REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 2. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover.
| 3. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch) |
![]() ![]() |
Place protective tape as shown in the illustration.
Text in Illustration *1
Protective Tape
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
| 4. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch) |
![]() ![]() |
Place protective tape as shown in the illustration.
Text in Illustration *1
Protective Tape
Using a moulding remover, detach the 6 claws.
Disconnect the connector and remove the instrument side panel.
| 5. REMOVE COWL SIDE TRIM BOARD RH |
![]() ![]() |
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
| 6. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 7. REMOVE REAR STEP COVER |
![]() ![]() |
- HINT:
- Use the same procedure to remove the step cover on the other side.
Detach the 2 claws and remove the step cover.
| 8. REMOVE REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 9. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
![]() ![]() |
Detach the 6 clips and remove the support plate.
| 10. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
![]() ![]() |
- HINT:
- Use the same procedure to remove the tonneau cover holder cap on the other side.
Detach the 2 claws and remove the tonneau cover holder cap.
| 11. REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat) |
- HINT:
- Use the same procedures described for the rear No. 2 seat cover bezel.
| 12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
![]() ![]() |
- HINT:
- When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the cover.

Remove the bolt and rear No. 1 seat belt anchor.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

Detach the 3 claws and remove the cover.
Remove the bolt and rear No. 2 seat belt anchor.

w/ Rear No. 2 Seat, except Face to Face Seat Type:
Remove the clip and bolt.
Detach the 16 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Remove the clip.
Detach the 16 clips and 2 claws, and remove the quarter trim panel.


w/ Tonneau Cover:
Remove the screw and clip.
Detach the 16 clips and 2 claws, and remove the quarter trim panel.


| 13. REMOVE FUEL FILLER OPENING LID LOCK RETAINER |
![]() ![]() |
Turn the cable counterclockwise and remove the cable from the retainer.
Turn the lock retainer counterclockwise and remove the lock retainer.

| 14. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
Detach the 2 claws.

Disconnect the fuel lid lock control cable and remove the fuel lid lock open lever.
| 15. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
Using a screwdriver, disconnect the clamps shown in the illustration.
- HINT:
- Tape the screwdriver tip before use.


Remove the lock control cable.








