2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. A bolt without a torque specification is shown in the standard bolt chart (Click here).
  2. When installing the back door garnish, heat the vehicle body and back door garnish using a heat light.

    Standard Heating Temperature:
    Item
    Temperature
    Back Door Garnish
    20 to 30°C (68 to 86°F)
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the back door garnish and vehicle body excessively.


1. INSTALL REAR LICENSE LIGHT COVER
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B302227E01
    Install a new rear license light cover.
    Text in Illustration 
    *1
    Double-sided Tape

    1. Using a heat light, heat the vehicle body and a new rear license light cover.

    2. Remove the peeling paper from the face of the emblem.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the 7 claws to install the rear license light cover.

      HINT:
      Press the rear license light cover firmly to install it.


2. INSTALL LICENSE PLATE LIGHT ASSEMBLY

  1. E156994
    Install the 2 license plate lights with the 2 screws.


3. INSTALL NO. 2 BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE
  1. Pass the wire harness of the license plate light through the tail gate, and install the wire harness.

  1. Attach the 7 clips to install the No. 2 back door garnish.

    B186239

  1. B186238
    Install the 2 nuts and connect the connector.


4. INSTALL BACK DOOR TRIM PANEL ASSEMBLY
  1. Attach the 16 clips to install the back door trim panel assembly.

  1. Install the 4 bolts.


5. INSTALL BACK DOOR TRIM COVER RH

  1. B313306
    Install the back door trim cover RH as shown in the illustration.


6. INSTALL BACK DOOR TRIM COVER LH

  1. B313307
    Install the back door trim cover LH as shown in the illustration.


7. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Attach the 6 clips to install the support plate.


8. INSTALL SYMBOL EMBLEM

  1. B302224E01
    Clean the vehicle body surface.
    Text in Illustration 
    *1
    Boss

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new emblem.

    1. Using a heat light, heat the vehicle body and a new emblem.

    2. Remove the peeling paper from the face of the emblem.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Align the boss positions and install the emblem.

      HINT:
      Press the emblem firmly to install it.


9. INSTALL BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE RH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new back door garnish.

    1. Using a heat light, heat a back door garnish and the vehicle body surface.

    2. Remove the peeling paper from the face of the back door garnish.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the 7 clips and double-sided tape to install the back door garnish.

      HINT:
      Press the back door garnish firmly to install them.


      B186236E02

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →