2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE INSTRUMENT SIDE PANEL RH

B181912E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


3. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


4. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


6. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


7. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Detach the 2 claws and disconnect the DLC3.

  1. Remove the 5 bolts and lower instrument panel.


8. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


9. REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

  1. B184268
    Disconnect the connector.

  1. Remove the nut and double lock door control relay assembly.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →