2011-2013 Land Cruiser · Service Manual Suspension

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL NO. 1 FRONT STABILIZER BAR BUSH

  1. C173669E01
    Install the 2 bushes to the outer side of the bush stoppers on the front stabilizer bar as shown in the illustration.

    NOTICE:
    Be sure to install the front No. 1 stabilizer bar bushes so that the cut and bump of each bush faces the under of the vehicle.


2. INSTALL FRONT STABILIZER BAR

  1. C178728E01
    Set the stabilizer bracket so that the arrow mark is facing the front side of the vehicle.

  1. C173239
    Temporarily install the 2 stabilizer brackets and front stabilizer bar with the 4 bolts.


3. TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY LH
  1. Temporarily install the stabilizer link with the nut and bolt.

  1. C174417E01
    Tighten the nut.

    Torque:
    128 N*m{ 1305 kgf*cm , 94 ft.*lbf }


4. TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY RH

  1. C174416E01
    Temporarily install the stabilizer link with the nut and bolt.

  1. Tighten the nut.

    Torque:
    128 N*m{ 1305 kgf*cm , 94 ft.*lbf }


5. TIGHTEN NO. 1 FRONT STABILIZER BRACKET LH

  1. C173667E01
    Tighten the 2 bolts.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

    NOTICE:
    Tighten the bolts in 3 steps, in the order shown in the illustration.


6. TIGHTEN NO. 1 FRONT STABILIZER BRACKET RH

  1. C173668E01
    Tighten the 2 bolts.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

    NOTICE:
    Tighten the bolts in 3 steps, in the order shown in the illustration.


7. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover sub-assembly with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


8. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. Push in the clip to install the front fender splash shield sub-assembly LH.

  1. Install the 3 bolts and screw.


9. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Push in the clip to install the front fender splash shield sub-assembly RH.

  1. Install the 3 bolts and 2 screws.


10. STABILIZE SUSPENSION
  1. Install the front wheels.

    Torque:
    for aluminum wheel:
    131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
    for steel wheel:
    209 N*m{ 2131 kgf*cm , 154 ft.*lbf }

  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.


11. TIGHTEN FRONT STABILIZER LINK ASSEMBLY LH

  1. C174418E01
    Tighten the bolt.

    Torque:
    135 N*m{ 1376 kgf*cm , 100 ft.*lbf }

    NOTICE:
    Perform this procedure with all 4 wheels on the ground.


12. TIGHTEN FRONT STABILIZER LINK ASSEMBLY RH

  1. C174419E01
    Tighten the bolt.

    Torque:
    135 N*m{ 1376 kgf*cm , 100 ft.*lbf }

    NOTICE:
    Perform this procedure with all 4 wheels on the ground.

← INSTALLATION (Sep 2011 – Dec 2011)PROBLEM SYMPTOMS TABLE (Sep 2011 – Dec 2011) →