2011-2013 Land Cruiser · Service Manual Suspension

INSPECTION

Inspection · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Standard Cold Tire Inflation Pressure:
    Tire Size
    Destination
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    245/75R17
    Middle East
    230 (2.3, 33)
    230 (2.3, 33)
    260 (2.6, 38)*1
    General Export
    230 (2.3, 33)
    230 (2.3, 33)
    260 (2.6, 38)*1
    285/65R17
    Middle East
    230 (2.3, 33)
    230 (2.3, 33)
    Australia
    230 (2.3, 33)
    230 (2.3, 33)
    General Export
    230 (2.3, 33)
    230 (2.3, 33)
    Europe
    240 (2.4, 35)
    240 (2.4, 35)
    China
    240 (2.4, 35)
    240 (2.4, 35)
    285/60R18
    Middle East
    230 (2.3, 33)
    230 (2.3, 33)
    Australia
    230 (2.3, 33)
    230 (2.3, 33)
    General Export
    230 (2.3, 33)
    230 (2.3, 33)
    Europe
    240 (2.4, 35)
    240 (2.4, 35)
    China
    240 (2.4, 35)
    240 (2.4, 35)
    285/50R20
    Europe
    240 (2.4, 35)
    240 (2.4, 35)
    260 (2.6, 38)*1

    *1: For driving at 160 km/h (100 mph) or over

  1. R003031
    Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less


ROTATE TIRES

  1. C163157E04
    Rotate the tires as shown in the illustration.

    Torque:
    for Aluminum Wheel:
    131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
    for Steel Wheel:
    209 N*m{ 2131 kgf*cm , 154 ft.*lbf }

    Text in Illustration 
    *a
    Front of the Vehicle


INSPECT WHEEL BALANCE

  1. C144019
    for Steel Wheel Type:
    Check and adjust the off-the-car balance.

    Standard Imbalance After Adjustment:
    12 g (0.0265 lb) or less

    HINT:
    If necessary, check and adjust the on-the-car balance.

  1. for Aluminum Wheel Type:
    Check and adjust the off-the-car balance.

    Tire Size
    Standard Imbalance After Adjustment
    285/65R17
    7.5 g (0.0165 lb) or less
    285/60R18
    7.0 g (0.0154 lb) or less
    285/50R20
    6.5 g (0.0143 lb) or less

    C241067E02
    Text in Illustration 
    *a
    for 17 Inch Wheels
    *b
    for 18 Inch or 20 Inch Wheels

    NOTICE:
    1. Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be attached.
    2. Do not touch the adhesive surface of the tape.
    3. Attach a sticking-type balance weight to the flat surface (A) shown in the illustration.

      Width (A):
      20 mm (0.787 in.)

    4. Push the balance weight firmly so that it securely adheres to the position.
    5. Do not reuse the balance weight.

    HINT:
    1. For 17 inch wheels, the outer side balance weight should be installed by clipping it to the rim.
    2. If necessary, check and adjust the on-the-car balance.


INSPECT FRONT AXLE HUB
(Click here)

INSPECT REAR AXLE SHAFT
(Click here)
← INSPECTION (Sep 2011 – Dec 2011)PRECAUTION (Sep 2011 – Dec 2011) →