REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1.
REMOVE FRONT SEAT ASSEMBLY LH |
 |
Remove the front seat assembly (Click here).
| 2.
REMOVE VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)
|
 |
Using a screwdriver, detach the 2 claws and remove the vertical adjuster cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 3.
REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)
|
 |
Remove the 2 screws and vertical adjusting handle LH.
| 4.
REMOVE VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)
|
 |
Remove the snap ring and vertical seat adjuster knob.
| 5.
REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
|
 |
Lift the reclining adjuster release handle LH.
Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.
- HINT:
- Tape the screwdriver tip before use.
| 6.
REMOVE FRONT SEAT CUSHION SHIELD LH
|
 |
- w/ Seatback Board:
Disconnect the 2 rubber bands from the 2 hooks.
- w/o Seatback Board:
Disconnect the rubber band from the 2 hooks.
- for 4 Way Seat Type:
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.
- for 8 Way Seat Type:
Remove the 3 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.
w/ Lumbar Support:
Disconnect the lumbar switch connector.
| 7.
REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
|
 |
Disconnect the connectors and detach the clamps.
- Remove the nut and front seat inner belt assembly.
| 8.
REMOVE FRONT INNER SEAT CUSHION SHIELD LH
|
 |
Remove the screw.
Detach the claw and clip, and then remove the front inner seat cushion shield LH.
| 9.
REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)
|
 |
Remove the 2 screws.
Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.
| 10.
REMOVE FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)
|
 |
Detach the 4 claws and remove the 2 front seat headrest supports.
| 11.
REMOVE SEATBACK COVER WITH PAD
|
 |
w/ Seatback Board:
- Remove the 3 hog rings and detach the 9 hooks.
- w/ Front Seat Side Airbag:
Remove the nut and seatback cover bracket from the seat frame.
w/o Seatback Board:
- Remove the 3 hog rings.
- Open the 2 fasteners, and then open the front separate type seatback cover.
- w/ Front Seat Side Airbag:
Remove the nut and seatback cover bracket from the seat frame.
- Detach the 4 claws and remove the 2 front seat headrest supports.
Remove the seatback cover with pad from the seatback frame.
| 12.
REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support) |
 |
- Remove the 4 springs.
Remove the cable clamp and disconnect the active headrest cable from the seatback spring.
Detach the 4 hooks and remove the seatback spring.
- Disconnect the lumbar support adjuster connector.
Remove the 2 screws and lumbar support adjuster.