2011-2013 Land Cruiser · Service Manual Vehicle Exterior

TERMINALS OF ECU

System information · Vehicles built from Jan 2012


CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)
B157223E13
  1. Disconnect the L52 power back door unit assembly (power back door ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L52-10 (ECUB) - Body ground
    R - Body ground
    ECUB power supply
    Always
    11 to 14 V
    L52-12 (B) - Body ground
    B - Body ground
    Power supply
    Always
    11 to 14 V
    L52-8 (IG) - Body ground
    G - Body ground
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    L52-8 (IG) - Body ground
    G - Body ground
    IG power supply
    Engine switch off
    Below 1 V
    L52-15 (OSL) - L52-14 (OSE)
    G - BR
    Power back door sensor LH circuit
    Power back door sensor LH not pressed
    Approximately 1 kΩ
    L52-15 (OSL) - L52-14 (OSE)
    G - BR
    Power back door sensor LH circuit
    Power back door sensor LH pressed
    Below 100 Ω
    L52-13 (OSR) - L52-14 (OSE)
    Y - BR
    Power back door sensor RH circuit
    Power back door sensor RH not pressed
    Approximately 1 kΩ
    L52-13 (OSR) - L52-14 (OSE)
    Y - BR
    Power back door sensor RH circuit
    Power back door sensor RH pressed
    Below 100 Ω
    L52-11 (GND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    L52-17 (MSW) - Body ground
    G - Body ground
    Power back door main switch signal circuit
    Power back door main switch not pushed (on)
    Below 1 Ω
    L52-17 (MSW) - Body ground
    G - Body ground
    Power back door main switch signal circuit
    Power back door main switch pushed (off)
    10 kΩ or higher
    L52-4 (DS1) - Body ground
    R - Body ground
    Back door control switch signal circuit
    Back door control switch on
    Below 1 Ω
    L52-4 (DS1) - Body ground
    R - Body ground
    Back door control switch signal circuit
    Back door control switch off
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the L52 power back door unit assembly (power back door ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L52-26 (BZR+) - Body ground
    L - Body ground
    Power back door warning buzzer signal input
    Power back door warning buzzer sounding
    Pulse generation
    (See waveform 1)
    L52-26 (BZR+) - Body ground
    L - Body ground
    Power back door warning buzzer signal input
    Power back door warning buzzer stopped
    Below 1 V
    L52-2 (DC+) - L52-1 (DC-)
    R - B
    Power back door lock motor circuit
    Power back door lock motor operating
    11 to 14 V
    L52-2 (DC+) - L52-1 (DC-)
    R - B
    Power back door lock motor circuit
    Power back door lock motor stopped
    Below 1 V
    L52-17 (MSW) - Body ground
    G - Body ground
    Power back door main switch signal circuit
    Power back door main switch not pushed (on)
    Below 1 V
    L52-17 (MSW) - Body ground
    G - Body ground
    Power back door main switch signal circuit
    Power back door main switch pushed (off)
    Pulse generation
    (See waveform 2)
    L52-20 (FUL) - Body ground
    W - Body ground
    Back door courtesy switch signal circuit
    Back door opened
    Below 1 V
    L52-20 (FUL) - Body ground
    W - Body ground
    Back door courtesy switch signal circuit
    Back door closed
    Pulse generation
    (See waveform 3)
    L52-4 (DS1) - Body ground
    R - Body ground
    Back door control switch signal circuit
    Back door control switch on
    Below 1 V
    L52-4 (DS1) - Body ground
    R - Body ground
    Back door control switch signal circuit
    Back door control switch off
    Pulse generation
    (See waveform 4)
    L52-22 (HAF) - Body ground
    G - Body ground
    Back door lock half-latch switch signal circuit
    Back door opened
    Below 1 V
    L52-22 (HAF) - Body ground
    G - Body ground
    Back door lock half-latch switch signal circuit
    Back door closed
    Pulse generation
    (See waveform 5)
    L52-24 (POS) - Body ground
    B - Body ground
    Back door lock position switch signal circuit
    Back door closed
    Below 1 V
    L52-24 (POS) - Body ground
    B - Body ground
    Back door lock position switch signal circuit
    Back door opened
    Pulse generation
    (See waveform 6)
    L52-23 (CYLH) - Body ground
    G - Body ground
    Lower tail gate courtesy switch LH circuit
    Lower tail gate opened
    Below 1 V
    L52-23 (CYLH) - Body ground
    G - Body ground
    Lower tail gate courtesy switch LH circuit
    Lower tail gate closed
    Pulse generation
    (See waveform 7)
    L52-7 (CYRH) - Body ground
    Y - Body ground
    Lower tail gate courtesy switch RH circuit
    Lower tail gates opened
    Below 1 V
    L52-7 (CYRH) - Body ground
    Y - Body ground
    Lower tail gate courtesy switch RH circuit
    Lower tail gate closed
    Pulse generation
    (See waveform 8)

  5. B194850E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-26 (BZR+) - Body ground
    Tool Setting
    5 V/DIV., 1 ms/DIV
    Condition
    Power back door warning buzzer sounding

  6. B194849E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-17 (MSW) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Power back door main switch pushed (off)

  7. B194850E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-20 (FUL) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Back door closed

  8. B194850E01
    Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-4 (DS1) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Back door lock control switch off

  9. B194850E01
    Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-22 (HAF) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Back door closed

  10. B194849E01
    Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-24 (POS) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Back door opened

  11. B194849E01
    Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-23 (CYLH) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Lower tail gate closed

  12. B194849E01
    Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L52-7 (CYRH) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Lower tail gate closed


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E03
  1. Disconnect the 2A, 2B, 2D, E2 and E3 main body ECU (cowl side junction block LH) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-20 (BATB) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    2A-1 (ACC) - Body ground
    B - Body ground
    ACC power supply
    Always
    11 to 14 V
    E2-2 (PBDS) - Body ground
    R - Body ground
    Door control switch circuit
    Door control switch pushed (on)
    Below 1 Ω
    E2-2 (PBDS) - Body ground
    R - Body ground
    Door control switch circuit
    Door control switch not pushed (off)
    10 kΩ or higher
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the 2A, 2B, 2D, E2 and E3 ECU (cowl side junction block LH) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E2-2 (PBDS) - Body ground
    R - Body ground
    Door control switch circuit
    Door control switch pushed (on)
    Below 1 V
    E2-2 (PBDS) - Body ground
    R - Body ground
    Door control switch circuit
    Door control switch not pushed (off)
    Pulse generation
    (See waveform 1 or 2)

  5. B201885E01
    Using an oscilloscope, check waveform.
    Waveform1 (Reference) 
    Item
    Content
    Terminal (Symbol)
    E2-2 (PBDS) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Door control switch not pushed (off)

  6. B201886E01
    Using an oscilloscope, check waveform.
    Waveform2 (Reference) 
    Item
    Content
    Terminal (Symbol)
    E2-2 (PBDS) - Body ground
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Door control switch not pushed (off)

← PROBLEM SYMPTOMS TABLE (from Jan 2012)DTC CHECK / CLEAR (from Jan 2012) →