DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the tester, read the Data List.
Back Door Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Lock Status
Back door lock status signal / Lock or Unlock
Lock: Back door locked
Unlock: Back door unlocked
-
Half Latch SW
Half-latch switch signal / ON or OFF
ON: Half-latch switch on
OFF: Half-latch switch off
-
Closer Position SW
Closer position switch signal / ON or OFF
ON: Closer position switch on
OFF: Closer position switch off
-
Courtesy SW
Back door courtesy switch signal / ON or OFF
ON: Back door courtesy switch on
OFF: Back door courtesy switch off
-
RH CTSY SW of Tail Gate Panel
Lower tail gate courtesy switch RH signal / ON or OFF
ON: Tail gate closed
OFF: Tail gate open
-
LH CTSY SW of Tail Gate Panel
Lower tail gate courtesy switch LH signal / ON or OFF
ON: Tail gate closed
OFF: Tail gate open
-
PBD Touch Sensor (Right)
Power back door sensor RH signal / ON, OFF or Open
ON: Power back door sensor RH pressed
OFF: Power back door sensor RH not pressed
Open: Power back door sensor RH circuit open
-
PBD Touch Sensor (Left)
Power back door sensor LH signal / ON, OFF or Open
ON: Power back door sensor LH pressed
OFF: Power back door sensor LH not pressed
Open: Power back door sensor LH circuit open
-
PBD Main SW
Power back door main switch signal / ON or OFF
ON: Power back door main switch not pressed
OFF: Power back door main switch pressed
-
PBD Close SW
Back door control switch signal / ON or OFF
ON: Back door control switch on
OFF: Back door control switch off
-
IG SW
Engine switch signal / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
PBD Position (Close-1/4)
Back door position (Full close - 1/4 open) / Caution or OK
Caution: Back door position is not fully closed to 1/4 opened
OK: Back door position is fully closed to 1/4 opened
-
PBD Position (1/4-2/4)
Back door position (1/4 open - 2/4 open) / Caution or OK
Caution: Back door position is not 1/4 opened to 2/4 opened
OK: Back door position is 1/4 opened to 2/4 opened
-
PBD Position (2/4-3/4)
Back door position (2/4 open - 3/4 open) / Caution or OK
Caution: Back door position is not 2/4 opened to 3/4 opened
OK: Back door position is 2/4 opened to 3/4 opened
-
PBD Position (3/4-Open)
Back door position (3/4 open - Full open) / Caution or OK
Caution: Back door position is not 3/4 opened to fully opened
OK: Back door position is 3/4 opened to fully opened
-
PBD SW Operation
Power back door switch operation condition signal / 0.0s or 0.8s
Current customize setting displayed
-
PBD Buzz In Use
Power back door warning buzzer operation condition signal / ON or OFF
Current customize setting displayed
-
Wireless PBD SW Operation
Transmitter switch operation condition signal / 1 time, 2 times, 0.8 sPR, OFF
Current customize setting displayed
-
# Codes
Number of stored trouble codes / min.: 0, max.: 255
Number of DTCs will be displayed
-
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Back Door Open SW
Door control switch signal / ON or OFF
ON: Door control switch on
OFF: Door control switch off
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Back Door / Active Test.
According to the display on the tester, perform the Active Test.
Back Door Tester Display
Test Part
Control Range
Diagnostic Note
Latch Releaser
Operate back door lock
ON / OFF
-
PBD Motor
Operate power back door motor
Forward / OFF
Reverse / OFF
-
PBD Clutch
Operate power back door clutch
ON / OFF
-
PBD Buzzer
Operate warning buzzer
ON / OFF
-
Courtesy SW Signal
Operate back door courtesy light switch signal
ON / OFF
-
PBD Close SW Light
Operate PBD close switch Light
ON / OFF
-