2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

OPERATION CHECK

Troubleshooting · Vehicles built from Jan 2012


CHECK HARD DISK DRIVE

HINT:
  1. Check the hard disk drive (HDD) built into the multi-media module receiver assembly.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E226244
    Select "Failure Diagnosis" from the "Service Menu" screen.

  3. E225796
    Select "HDD Check" from the "Failure Diagnosis" screen.

  4. E225797E01
    HDD Check

    1. Select "HDD Check" to start the HDD check.

    2. Check that the result is displayed when the HDD check is completed.

      Screen Description 
      Display (Result)
      Description
      Checking
      Check is in progress
      OK
      Hard disk drive is normal
      NG
      Hard disk drive is malfunctioning
      Text in Illustration 
      *a
      Result

      HINT:
      1. After selecting "HDD Check", it may take a while until the result is displayed.
      2. If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the HDD may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.
      3. If "NG" is displayed even when the cabin temperature is appropriate, replace the HDD with a new one.


CHECK PANEL & STEERING SWITCH

HINT:
  1. The multi-media module receiver assembly panel switches and steering switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225778
    Select "Panel&Steering Switch" from the "Function Check/Setting I" screen.

  4. Panel & Steering Switch Check Mode

    1. E225786E01
      Operate each switch and check that the switch conditions are correctly displayed.
      Screen Description 
      Display
      Content
      *a: Switch condition
      "Pushed" is displayed when any switch is pushed
      *b: Number of switches pushed
      1. Number of switches pushed at once is displayed
      2. If more than 3 switches are pushed at once, "More than 3" is displayed
      *c: Rotary switch direction
      Direction of rotary switch is displayed

      NOTICE:
      When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225779
    Select "Touch Switch" from the "Function Check/Setting I" screen.

  4. E176521
    Touch Switch Check

    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MIC & VOICE RECOGNITION

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225780
    Select "Mic&Voice Recognition" from the "Function Check/Setting I" screen.

  4. E187218E13
    Microphone & Voice Recognition Check
    Screen Description 
    Display
    Content
    *a: Microphone input level meter
    Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
    *b: Recording switch
    Starts recording.
    *c: Stop switch
    Stops recording and playing.
    *d: Play switch
    Plays the recorded voice.
    *e: Recording indicator
    Comes on while recording.

    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      HINT:
      The microphone is active at all times when this screen is displayed.

    2. Push the recording switch and perform voice recording.

      HINT:
      1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
      2. While recording or playing, the switches other than the stop switch cannot be pushed.
      3. When no recording is present, the play switch cannot be pushed.
      4. Recording will stop after 5 seconds or when the stop switch is pushed.

    3. Check that the recording indicator remains on while recording and that the recording can be played normally.


CHECK COLOR BAR

HINT:
  1. The display color on the screen is checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225781
    Select "Color Bar" from the "Function Check/Setting I" screen.

  4. Color Bar Check Mode

    1. E226305
      Select a color bar from the "Color Bar Check Mode" screen.

    2. Check the display color.

      HINT:
      1. The entire screen turns to the color or stripe selected.
      2. Touching the display will return to the "Color Bar Check Mode" screen.


CHECK GPS & VEHICLE SENSORS

HINT:
  1. GPS information, vehicle signals and sensor signals are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225782
    Select "GPS&Vehicle Sensors" from the "Function Check/Setting I" screen.

  4. E246906
    Select "Sensors Check" from the "GPS Information" screen.

  5. E226261E01
    Vehicle Sensors
    Screen Description 
    Display
    Content
    *a: Vehicle signal
    Vehicle speed signal condition is displayed.
    *b: Sensor signal
    Gyro sensor output condition is displayed.

    HINT:
    This screen is updated once per second.


    1. Check all the signals and sensors when vehicle signal information is displayed.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the multi-media module receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225783
    Select "Vehicle Signal" from the "Function Check/Setting I" screen.

  4. Vehicle Signal Check Mode

    1. E225776
      When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
      Screen Description 
      Display
      Content
      Battery
      Battery voltage is displayed.
      IG
      Engine switch ON/OFF state is displayed.
      PKB
      Parking brake ON/OFF state is displayed.
      REV
      Reverse signal ON/OFF state is displayed.
      SPEED
      Vehicle speed is displayed in km/h.
      TAIL
      Tail signal (Light control switch) ON/OFF state is displayed.
      ADIM/TCAN
      Brightness state DIM (with) / BRIGHT (without) is displayed.

      HINT:
      1. Only items sending vehicle signals will be displayed.
      2. This screen displays vehicle signals input to the multi-media module receiver assembly.
      3. This screen is updated once per second when vehicle input signals change.


CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

HINT:
  1. The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E225784
    Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

  4. E239452E01
    Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)
    Screen Description 
    Display
    Content
    *a: Receive voice level adjustment
    Setting for the voice level received from "Bluetooth" compatible phones.
    *b: Send voice level adjustment
    Setting for the voice level sent from "Bluetooth" compatible phones.

    NOTICE:
    Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.


    1. If the voice level is low, press the up button, and if the voice level is loud, press the down button.

      HINT:
      1. Settings will be applied when the up or down button is selected.
      2. The received voice level adjustment ranges from -5 to +1.
      3. The sent voice level adjustment ranges from -5 to +4.
      4. The initial level is "0".

  5. E239453E01
    Hands-Free Voice Quality Setting (Voice Quality Type adjustment)
    Screen Description 
    *a
    Numeric keypad
    *b
    Setting button
    *c
    Reset button

    1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

    2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A
      (Noise)
      The change in background noise the other party hears becomes unpleasant.
      1000
      The change in background noise the other party hears is reduced.
      Background noise when not talking becomes large.
      B
      (Noise)
      The volume of the noise the other party hears temporarily becomes large.
      2000
      The temporary noise is reduced.
      The volume of voice may drop temporarily.
      C
      (Echo)
      The other party hears weak echoes.
      0100
      The amount of echo is reduced (low level).
      Sound quality of the other party deteriorates (low level).
      D
      (Echo)
      The other party hears strong echoes.
      0200
      The amount of echo is reduced (high level).
      Sound quality of the other party deteriorates (high level).
      E
      (Quality)
      The other party hears harsh noises.
      0010
      Sound the other party hears becomes soft.
      Sound the other party hears becomes muffled.
      F
      (Quality)
      You hear harsh noises.
      0020
      Sound you hear becomes soft.
      Sound you hear becomes muffled.
      Settings (When multiple phenomenon occurred) 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A+C
      The change in background noise the other party hears becomes unpleasant and the other party hears weak echoes.
      1100
      1. The change in background noise the other party hears is reduced.
      2. The amount of echo is reduced (low level).
      1. Background noise when not talking becomes large.
      2. Sound quality of the other party deteriorates (low level).
      A+D
      The change in background noise the other party hears becomes unpleasant and the other party hears strong echoes.
      1200
      1. The change in background noise the other party hears is reduced.
      2. The amount of echo is reduced (high level).
      1. Background noise when not talking becomes large.
      2. Sound quality of the other party deteriorates (high level).
      B+C
      The volume of the noise the other party hears temporarily becomes large and the other party hears weak echoes.
      2100
      1. The temporary noise is reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      B+D
      The volume of the noise the other party hears temporarily becomes large and the other party hears strong echoes.
      2200
      1. The temporary noise is reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).
      C+E
      The other party hears weak echoes and harsh noises.
      0110
      1. The amount of echo is reduced (low level).
      2. Sound the other party hears becomes soft.
      1. Sound quality of the other party deteriorates (low level).
      2. Sound the other party hears becomes muffled.
      C+F
      The other party hears weak echoes and you hear harsh noises.
      0120
      1. The amount of echo is reduced (low level).
      2. Sound you hear becomes soft.
      1. Sound quality of the other party deteriorates (low level).
      2. Sound you hear becomes muffled.

      HINT:
      1. The default value is "0000".
      2. Settings will be applied when the setting button is selected.
      3. If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
      4. If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.


CHECK DAB RECEPTION (w/ DAB Function)

HINT:
  1. The reception condition of DAB (Digital Audio Broadcast) can be checked.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E225777
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E235730
    Select "Next Page" from the "Function Check/Setting I" screen.

  4. E235721
    Select "DAB Reception Check" from the "Function Check/Setting II" screen.

  5. E245217E02
    Select "DAB Reception Check" from the "Function Check/Setting II" screen.
    *a: Channel Change Switch Description 
    Display
    Content
    Up or down button
    Enables the channel to be changed to the one to be checked.
    *b: Check Switch Description 
    Display
    Condition
    Content
    Check
    Before/after check
    Starts checking
    STOP
    During check
    Stops checking
    *c: Antenna Connection Check Result Description 
    Display
    Content
    OK
    Connected properly
    NG
    Not connected properly
    -
    Not equipped with DAB antenna.
    *d: DAB Tuner Reception Level Check Result Description 
    Display
    Content
    Black
    Good reception
    Red
    Poor reception
    -
    Not equipped with DAB antenna.

    1. Select the "Check" button to start the DAB reception check.

    2. Check that the result is displayed when the DAB reception check is performed.


CHECK UNIT VERSION INFORMATION

HINT:
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E229432
    Select "Service Information" from the "Service Menu" screen.

  3. E228230
    Select "Version Information" from the "Service Information" screen.

  4. E248722
    Press the "Push" switch.

  5. E228232E01
    Unit Version Information
    Screen Description 
    Display
    Content
    *a: Device name
    Target device
    *b: Manufacturer name
    Manufacturer of the ECU (target device)
    *c: Component name
    Component name of the ECU (target device)
    *d: Version
    Version of the ECU (target device)

    HINT:
    Depending on the manufacturer, some component names and versions will be displayed differently.


CHECK SOFTWARE ERROR HISTORY

HINT:
This function is used to check the cause when the multi-media module receiver assembly screen is blacked out.

  1. Check software error history.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

    5. When an item is stored for Software Error History, record it before repairing the multi-media module receiver assembly.

      Software Error History Screen Description 
      Error Description
      Trigger
      Detail
      Software Reset
      Navi Microcomputer
      Hexadecimal Number
      Audio Microcomputer
      CAN Microcomputer
      No Video Signal
      Front Monitor
      Rear Monitor
      MOST Cold Restart
      Always

      HINT:
      1. Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the intelligent tester occurs, a "-" is displayed for the display items.

  2. Clear software error history.

    1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).

      1. Cleared using the intelligent tester.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.


CHECK OPTICAL DISC ERROR HISTORY

HINT:
This function is used to check the cause when an optical disc error occurs.

  1. Check optical disc error history.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

    5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

      Optical Disc Error History Screen Description 
      Display
      Content
      Error Type
      Displays the type of error.
      Device
      Displays the malfunctioning device.
      Date
      Displays the date and time that the malfunction occurred.
      "Error Type" Screen Description 
      Error Type
      Detection Condition
      Action
      Read Error
      When a disc read error occurs.
      Proceed to next suspected area shown in Problem Symptoms Table (Click here)
      Disc damaged/up side down/dirty
      When it is determined that any of the following is the cause of the disc read error:
      1. The disc cannot be read.
      2. The disc cannot be read because of dirt or scratches.
      3. The disc cannot be read because it is inserted up side down.
      Cannot determine disc type
      An unsuitable disc is inserted.
      DPS error
      When an error occurs while decoding MP3/WMA files.
      Some files are corrupt
      1. When MP3/WMA files cannot be played back because they are unsupported.
      2. Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.
      Some files cannot be found
      1. When a disc without music data is played back.
      2. When there are no playable MP3/WMA files.
      Copy protection violation
      When a file with copyright protection that cannot be played back is played back.
      "Device" Screen Description 
      Device
      Component
      DVD-P
      Multi-media module receiver assembly
      CD-P
      Not available
      R-Seat DVD-P
      Not available

      HINT:
      1. Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the intelligent tester occurs, a "-" or blank is displayed for the display items.

  2. Clear optical disc error history.

    1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).

      1. Cleared using the intelligent tester.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.

← IDENTIFICATION OF NOISE SOURCE (Sep 2011 – Dec 2011)PROBLEM SYMPTOMS TABLE (Sep 2011 – Dec 2011) →