INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1. INSTALL POWER OUTLET SOCKET COVER NO.2 |
Engage the 2 claws and install the power outlet socket cover.
| 2. INSTALL POWER OUTLET SOCKET ASSEMBLY |
Engage the claw and install the power outlet socket assembly.
Engage the 4 claws and install the power outlet socket bezel.
| 3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
![]() ![]() |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }


w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip.


w/ Tonneau Cover:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the screw and clip.


w/ Rear No. 2 Seat, except Face to Face Seat Type:

Install the rear No. 2 seat belt anchor with the bolt.- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
Install the rear No. 1 seat belt anchor with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 3 claws to install the cover.

| 4. INSTALL REAR SEAT COVER CAP (except Face to Face Seat Type) |
![]() ![]() |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 5. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
![]() ![]() |
- HINT:
- Use the same procedure to install the tonneau cover holder cap on the other side.
Attach the 2 claws to install the tonneau cover holder cap.
| 6. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE |
![]() ![]() |
Attach the 6 clips to install the support plate.
| 7. INSTALL REAR DOOR SCUFF PLATE LH |
![]() ![]() |
Attach the 3 claws and 4 clips to install the scuff plate.
Install the screw.
| 8. INSTALL REAR STEP COVER |
![]() ![]() |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 9. INSTALL REAR NO. 2 SEAT ASSEMBLY (except Face to Face Seat Type) |
![]() ![]() |
Temporarily install the seat assembly with the 4 bolts.
- NOTICE:
- Be careful not to damage the vehicle body.
Tighten the bolts in the order shown in the illustration.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 10. INSTALL REAR NO. 2 SEAT HINGE COVER LH (except Face to Face Seat Type) |
Attach the clip and 2 claws to install the cover.
| 11. INSTALL REAR SEAT CUSHION HINGE COVER LH (except Face to Face Seat Type) |
Attach the 3 claws to install the cover.
Return the seat to the upright position.
| 12. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY LH (w/ Rear Center Seat Headrest) |
| 13. INSTALL REAR NO. 2 SEAT ASSEMBLY (for Face to Face Seat Type) |
![]() ![]() |
Temporarily install the rear No. 2 seat with the 4 bolts.
Tighten the bolts in the order shown in the illustration.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 14. INSTALL REAR SIDE SEAT LEG PROTECTOR LH (for Face to Face Seat Type) |
![]() ![]() |
Attach the 2 claws to install the protector.
| 15. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.









