2011-2013 Land Cruiser · Service Manual General

TORQUE SPECIFICATIONS

Specifications · Vehicles built from Jan 2012

CAMSHAFT 
Part Tightened
N*m
kgf*cm
ft.*lbf
Camshaft housing sub-assembly LH x Cylinder head LH
for bolt A
10
102
7
except bolt A
30
306
22
Camshaft bearing cap LH x Camshaft housing sub-assembly LH
16
163
12
Camshaft housing sub-assembly RH x Cylinder head RH
for bolt A
10
102
7
except bolt A
30
306
22
Camshaft bearing cap RH x Camshaft housing sub-assembly RH
16
163
12
No. 2 chain tensioner assembly x No. 1 camshaft bearing cap RH
10
102
7
No. 1 chain vibration damper RH x Cylinder block and Cylinder head RH
21
214
15
No. 1 chain tensioner assembly RH x Cylinder head RH
10
102
7
No. 3 chain tensioner assembly x No. 2 camshaft bearing cap RH
10
102
7
No. 1 chain tensioner assembly LH x Cylinder head LH
10
102
7
No. 1 chain vibration damper LH x Cylinder block and Cylinder head LH
21
214
15
Camshaft timing gear assembly LH x No. 3 camshaft sub-assembly
100
1020
74
Camshaft timing exhaust gear assembly LH x No. 4 camshaft sub-assembly
100
1020
74
Camshaft timing gear assembly RH x No. 1 camshaft sub-assembly
100
1020
74
Camshaft timing exhaust gear assembly RH x No. 2 camshaft sub-assembly
100
1020
74
CYLINDER HEAD GASKET 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder head sub-assembly LH x Cylinder block (Cylinder head set bolt)
1st
36
367
27
2nd
Turn 90°
Turn 90°
Turn 90°
3rd
Turn 90°
Turn 90°
Turn 90°
Cylinder head sub-assembly LH x Cylinder block
21
214
15
Cylinder head sub-assembly RH x Cylinder block (Cylinder head set bolt)
1st
36
367
27
2nd
Turn 90°
Turn 90°
Turn 90°
3rd
Turn 90°
Turn 90°
Turn 90°
Cylinder head sub-assembly RH x Cylinder block
21
214
15
ENGINE ASSEMBLY 
Part Tightened
N*m
kgf*cm
ft.*lbf
Engine hanger x Cylinder head
43
438
32
No. 2 front engine mounting bracket LH x Frame
32
326
24
Front engine mounting insulator RH x Front No. 1 engine mounting bracket RH
72
734
53
Front engine mounting insulator LH x Front No. 1 engine mounting bracket LH
72
734
53
Front engine mounting insulator LH x Front No. 1 engine mounting bracket LH
for nut
72
734
53
for bolt
79
806
58
Front engine mounting insulator RH x Front No. 1 engine mounting bracket RH
for nut
72
734
53
for bolt
79
806
58
Rear drive plate spacer x Drive plate and ring gear sub-assembly x Crankshaft angle sensor rotor x Crankshaft
1st
30
301
22
2nd
Turn 90°
Turn 90°
Turn 90°
No. 1 water by-pass pipe x Cylinder head cover sub-assembly LH
18
184
13
Positive battery terminal x Wire harness
5.4
55
48 in.*lbf
Ground wire x Body panel
8.4
85
74 in.*lbf
Wire harness x Engine room junction block
10
102
7
Ground wire x Cylinder head cover sub-assembly RH
8.0
82
71 in.*lbf
Battery clamp sub-assembly x Body
for bolt
12
122
9
for nut
5.0
51
44 in.*lbf
Hood sub-assembly x Hood hinge
13
133
10
Hood hinge x Body
18
184
13
Oil pan protector assembly x Body
63
642
46
No. 2 engine under cover x Frame
29
296
21
No. 1 engine under cover sub-assembly x No. 2 engine under cover sub-assembly and Frame
29
296
21
ENGINE UNIT 
Part Tightened
N*m
kgf*cm
ft.*lbf
Timing chain cover sub-assembly x Stud bolt
20
199
14
No. 1 oil pan sub-assembly x Stud bolt
for stud bolt A
5.0
51
44 in.*lbf
for stud bolt B
9.0
92
80 in.*lbf
Oil drain pipe sub-assembly x Cylinder block
10
102
7
Engine rear oil seal retainer x Cylinder block
10
102
7
Oil pan strainer sub-assembly x No. 1 oil pan sub-assembly
12
122
9
No. 1 oil pan baffle plate x No. 1 oil pan sub-assembly
12
122
9
No. 1 oil pan sub-assembly x Cylinder block
for bolt A
10
102
7
for bolt B
35
357
26
for nut
35
357
26
No. 2 oil pan sub-assembly x No. 1 oil pan sub-assembly
10
102
7
No. 1 heat exchanger cover x Cylinder block
for bolt C
10
102
7
for bolt A, bolt B and nut
21
214
15
Cylinder head cover spacer x Cylinder head cover sub-assembly LH and RH
10
102
7
Cylinder block water drain cock sub-assembly x Cylinder block
30
306
22
Water drain cock plug x Cylinder block water drain cock sub-assembly
13
130
9
Camshaft timing oil control valve assembly x Cylinder head sub-assembly LH and RH
10
102
7
Oil filler cap housing x Cylinder head cover sub-assembly LH
10
102
7
Noise filter x Cylinder head cover sub-assembly LH and RH
10
102
7
Ignition coil assembly x Cylinder head cover sub-assembly LH and RH
10
102
7
Engine wire x No. 1 heat exchanger cover
8.0
82
71 in.*lbf
Front No. 1 engine mounting bracket LH x Cylinder block
35
357
26
Front No. 1 engine mounting bracket RH x Cylinder block
35
357
26
No. 1 EGR pipe bracket x No. 1 heat exchanger cover and Cylinder block
21
214
15
No. 1 water outlet pipe x No. 1 EGR pipe bracket
10
102
7
No. 3 air tube x Cylinder head cover sub-assembly RH
10
102
7
No. 4 air tube x Cylinder head cover sub-assembly LH
10
102
7
CYLINDER HEAD 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder head sub-assembly LH and RH x Stud bolt
9.0
92
80 in.*lbf
No. 2 straight screw plug x Cylinder head sub-assembly LH and RH
85
867
63
No. 1 straight screw plug x Cylinder head sub-assembly LH and RH
44
449
32
CYLINDER BLOCK 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder block x Stud bolt
for stud bolt A
20
199
14
for stud bolt B
9.0
92
80 in.*lbf
No. 1 oil nozzle sub-assembly x Cylinder block
10
102
7
Crankshaft bearing cap x Cylinder block
for inner position
1st
61
622
45
2nd
Turn 90°
Turn 90°
Turn 90°
for outer position
1st
27
275
20
2nd
Turn 90°
Turn 90°
Turn 90°
Cylinder block x Crankshaft bearing cap
45
459
33
Connecting rod bearing x Connecting rod
1st
40
408
30
2nd
Turn 90°
Turn 90°
Turn 90°
← SERVICE DATA (from Jan 2012)SERVICE DATA (from Sep 2011) →