2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. REMOVE SPARE TIRE (w/ Tire Carrier)

2. REMOVE SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

  1. B292610
    Detach the 2 claws and remove the spare wheel carrier hinge bracket.


3. REMOVE SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

  1. B292611
    Remove the 2 nuts.

  1. B292612
    Detach the clip and remove the spare wheel cover.


4. REMOVE SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)
  1. Remove the 3 bolts and spare tire.

  1. B292613
    Remove the 9 bolts and spare wheel carrier.


5. REMOVE ASSIST GRIP LH (for LH Side)

  1. B291735E01
    Using a screwdriver, detach the 2 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B291736
    Remove the 2 bolts and assist grip.


6. REMOVE DOOR INSIDE HANDLE BEZEL LH (for LH Side)

  1. B295796
    Detach the claw and open the cover.

  1. B291737
    Remove the screw.

  1. B291738E01
    Using a screwdriver, detach the 2 claws.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Detach the guide and remove the door inside handle bezel in the direction indicated by the arrow in the illustration.


7. REMOVE BACK DOOR TRIM PANEL ASSEMBLY LH (for LH Side)

  1. B291739
    Detach the 10 clips and remove the back door trim panel.


8. REMOVE ASSIST GRIP RH (for RH Side)

  1. B291761E01
    Using a screwdriver, detach the 2 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B291762
    Remove the 2 bolts and assist grip.


9. REMOVE BACK DOOR TRIM COVER RH (for RH Side)

  1. B291760
    Detach the 5 clips and 2 claws.

  1. B291796
    Detach the clamp and 2 claws and remove the back door trim cover.


10. REMOVE BACK DOOR TRIM PANEL ASSEMBLY RH (for RH Side)

  1. B291763
    Detach the 13 clips and remove the back door trim panel.


11. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)
  1. Open the wiper arm head cap.

  1. B283521
    Remove the nut and remove the rear wiper arm and blade assembly.


12. REMOVE BACK DOOR CENTER WEATHERSTRIP (for RH Side)

  1. B291773
    Detach the 5 clips and remove the back door center weatherstrip.


13. REMOVE BACK DOOR GLASS LH

  1. B293866E01
    Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    NOTICE:
    When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connectors.

  1. B294129E01
    Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks do not need to be placed if the glass is not going to be reused.

  1. B293868E01
    From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.

    NOTICE:
    Make sure not to damage the wire harness.

    Text in Illustration 
    *1
    Clip
    *2
    Piano Wire

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. Cut through the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back door glass.

  1. Using suction cups, remove the back door glass.


14. REMOVE BACK DOOR GLASS RH

  1. B293867E01
    Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    NOTICE:
    When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

  1. Disconnect the connectors.

  1. B294130E01
    Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks do not need to be placed if the glass is not going to be reused.

  1. B293869E01
    From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.

    NOTICE:
    Make sure not to damage the wire harness.

    Text in Illustration 
    *1
    Clip
    *2
    Piano Wire

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. Cut through the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back door glass.

  1. Using suction cups, remove the back door glass.


15. CLEAN VEHICLE BODY

  1. B106081E18
    Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      Text in Illustration 
      *1
      Adhesive
      *2
      Vehicle Body

← COMPONENTS (from Sep 2011)INSTALLATION (from Sep 2011) →