Home › Vehicle Exterior › BODY PANEL › BACK DOOR OPENING TROUGH
BM38G0E _01 Vehicle Exterior _101965 BODY PANEL _0472902 BACK DOOR OPENING TROUGH F

BODY PANEL  BACK DOOR OPENING TROUGH  ASSEMBLY REPLACEMENT  


K161936

With the quarter panel cut and join replacement sections (large areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points

K161585


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, weld the quarter panel extension front, side panel rear end patch, back door opening reinforcement lower and back door side stopper retainer with the standard number of welding points.

K161586C01
2.667,1 2.833,1 2.833,1 3.021,1.281 false 2.667,1.667 2.833,1.667 2.833,1.667 3.188,1.896 false 2.833,2.417 3,2.417 3,2.417 3.365,2.51 false 4.083,1.333 3.917,1.333 3.917,1.333 3.552,1.708 false 2.479,0.927 2.792,1.083 0.313,0.156 10 false *1 2.479,1.594 2.792,1.75 0.313,0.156 10 false *2 2.646,2.333 2.958,2.49 0.313,0.156 10 false *3 4.135,1.271 4.448,1.427 0.313,0.156 10 false *4 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A w/ Blind Spot Monitor System - -
*1 QUARTER PANEL EXTENSION FRONT *2 SIDE PANEL REAR END PATCH
*3 BACK DOOR OPENING REINFORCEMENT LOWER *4 BACK DOOR SIDE STOPPER RETAINER



d.

Before temporarily installing the new parts, weld the quarter panel extension front, back door opening reinforcement lower and back door side stopper retainer with the standard number of welding points.

K161587C01
2.667,1 2.833,1 2.833,1 3.021,1.281 false 2.833,2.417 3,2.417 3,2.417 3.365,2.51 false 4.083,1.333 3.917,1.333 3.917,1.333 3.552,1.708 false 2.479,0.927 2.792,1.083 0.313,0.156 10 false *1 2.646,2.333 2.958,2.49 0.313,0.156 10 false *2 4.135,1.271 4.448,1.427 0.313,0.156 10 false *3 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A w/o Blind Spot Monitor System - -
*1 QUARTER PANEL EXTENSION FRONT *2 BACK DOOR OPENING REINFORCEMENT LOWER
*3 BACK DOOR SIDE STOPPER RETAINER - -


K161588


e.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.